Search Results

Till recently supercharging was the most accepted technique for boost solution in gasoline engines. Recent advents in turbochargers introduced turbocharging technology into gasoline engines. Turbocharging of gasoline engines has helped in powertrains with higher power density and less overall weight. Along with the advantages in performance, new challenges arise, both in terms of thermal management as well as overall acoustic performance of powertrains. The study focuses mainly on NVH aspects of turbocharging of gasoline engines. Compressor surge is a most common phenomenon in turbochargers. As the operating point on the compressor map moves closer to the surge line, the compressor starts to generate noise. The amplitude and frequency of the noise depends on the proximity of the operating point to the surge line. The severity of noise can be reduced by selecting a turbocharger with enough compressor surge margin.

The present work is focussed on the real-world challenges of a dual mass flywheel (DMF) equipped vehicle in the Indian market. DMFs are widely used to isolate the drivetrain from the high torsional vibrations induced by the engine. While DMFs can significantly improve noise, vibration and harshness (NVH) characteristics of a vehicle, there are multiple challenges experienced in real-world operating conditions when compared with the single mass flywheel (SMF). The present work explains the challenges of using a DMF in a high power-density diesel powertrain for a multi-purpose vehicle (MPV) application in the Indian market. Measurements on the flat-road operating conditions revealed that the DMF vehicle is very sensitive for launch behaviour and requires a higher clutch modulation. Vibration measurements at the driver’s seat confirm that the SMF vehicle could be launched more comfortably at the engine idle speed of 850 RPM.

Dual mass flywheel (DMF) is an excellent solution to improve the noise, vibration, and harshness (NVH) characteristic of any vehicle by isolating the driveline from the engine torsional vibrations. For the same reason, DMF’s are widely used in high power-density diesel and gasoline engines. However, the real-world usage conditions pose a lot of challenges to the robustness of the DMF. In the present work, by capturing the Real-World Usage Profile (RWUP) conditions, a new methodology is developed to evaluate the robustness of a DMF fitted in a Sports utility vehicle (SUV). Ventilation holes are provided on clutch housing to improve convective heat transfer. Improvement in convective heat transfer will increase the life and will reduce clutch burning concerns. Cities like Mumbai, Chennai, Bangalore, roads will have clogged waters during rainy season. When the vehicle was driven in such roads, water enters inside the clutch housing through ventilation holes.

Dual mass flywheel (DMF) is an excellent solution to improve the noise, vibration and harshness (NVH) characteristic of any vehicle by isolating the driveline from the engine torsional vibrations. For the same reason, DMFs are widely used in high power-density diesel and gasoline engines. However, the real-world usage conditions pose a lot of challenges to the structural robustness of the DMF. In the present work, a new methodology is developed to evaluate the robustness of a DMF fitted in a compact sports utility vehicle (SUV) with rear-wheel drive architecture. The abuse conditions (mis-gear, sudden braking, etc) in the real-world usage could lead to a sudden engine stall leading to an abnormally high angular deceleration of the driveline components. The higher rate of deceleration coupled with the higher rotational moment of inertia of the systems might end up in introducing a significantly high impact torque on the DMF.

Hydrogen is considered as one of the potential alternate fuel and when compared to other alternate fuels like CNG, LPG, Ethanol etc., it has unique properties due to absence of carbon. In the current work, Hydrogen engine of 2.5 L, four cylinder, spark ignited Turbocharged-Intercooled engine is developed for Mini Bus application. Multi-point fuel injection system is used for injecting the hydrogen in the intake manifold. Initially, boost simulation is performed to select the optimum compression ratio and turbocharger. The literature review has shown that in-order to get the minimum NOx emissions Hydrogen engines must be operated between equivalence ratios ranging from 0.5 to 0.6. In the present study, full throttle performance is conducted mainly with the above equivalence ratio range with minimum advance for Maximum Brake Torque (MBT) ignition timing. At each operating point, the performance, emissions and combustion parameters are recorded and analyzed in detail.

Diesel engines have occupied a significant position in passenger car applications in the present automotive sector. Turbochargers find a very prominent role in diesel engines of all applications in order to achieve desired power and better fuel economy. Gaining higher torque at lower engine speeds with low smoke levels is a very tough task with fixed geometry turbochargers due to availability of lower air mass resulting in higher smoke emissions. Variable geometry turbochargers are capable of providing better torque at lower speeds and reduced smoke emissions on Common Rail Diesel engines. The Variable Geometry Turbocharger types used in this study are straight profile nozzle vanes (sample A) and curved profile nozzle vanes (sample B). The curved profile vanes as seen in sample B results in reduced variation of circumferential pressure distortions.

From International Energy Statistics (IES) survey, China, US and India are top three countries in emitting CO2 emissions. Further, worldwide national governments are focused to control CO2 emissions at source by stringent regulatory limits. OEMs and Research laboratories are working on several technology options such as advanced fuel injection system, optimizing in cylinder combustion system, thermal management and reduced engine friction to meet this legal requirements. In this paper, research work focused on improving combustion system through selection optimum bowl geometry and increasing volumetric efficiency through valve timings, profile and intake system using both 1D and 3D-CFD numerical approach. The main objective of this approach to utilize fossil fuel to its maximum potential in a single cylinder Naturally Aspirated (NA) water cooled engine with CRDI.

In Current scenario all Vehicle Manufacturer are looking towards cost effectiveness in their product development without compromising product quality and performance. With this reference, development of low cost FEAD (Front End Accessory Drive) system with stretch fit belt & idlers for multiple accessories has emerged as one of the alternative smart engineering solution against the FEAD with auto tensioner. The beauty of this low cost FEAD system is not only the cost saving but also the long lasting performance without affecting component life. In the current work, development of a low cost FEAD for 3 cylinder 1.5 litre diesel engine has been presented. It was one of the challenges to introduce stretch fit belt for 3 cylinder engine considering the high torsional vibration. The performance of this FEAD system was evaluated in terms of accessories pulley slip and belt flapping. The component durability was assessed both at engine as well as at vehicle level.

High speed diesel engines are difficult to start in cold conditions (at subzero temperature) because the cylinder head and cylinder block absorbs heat of compression and thus preventing ignition due to the high surface to volume ratio. Also the coolant and the engine oil become viscous at subzero temperature and make the condition unfavorable for starting. Combustion optimization along with the help of a heating aid can make these engines to start quickly without any engine misbehavior. Cold startability is the ability of an engine to start within a specified time and continue to run without any malfunctioning. Combustion instability will lead to the misfiring of the engine unless it is calibrated properly. The European countries are subjected to a minimum temperature of -20°C to -25°C. So the intention of this work is to optimize the cold startability of Mahindra's Multi-Purpose Vehicle (MPV) up to -25°C which is to be sold in European countries.

The prime objective of this study is to check the friction reduction by reducing the tangential load of the piston ring. To examine this experimental study has been carried out under motored engine condition from 500 to 4000 engine speed at the step of 500 rpm at different oil temperatures ranging from 40 °C to 120 °C. 15 W40 oil was used for this study. Standard Strip down approach was followed in accessing the Friction. The whole friction measurement was split in crank train and piston group friction and was measured with base and modified piston ring pack. The modified piston ring pack was having 24% less ring tension as compared to base ring pack. The study was carried out using block, crankshaft & Piston of 100 hp, 1.5 litre, 3 cylinder engine with 92 mm stroke and 83 mm bore. In each test ring pack was tested as a part of complete piston assembly.

Connecting rod of a high performance reciprocating internal combustion engine is one of the critical components exhibiting complex motion. This is subjected to both compressive load due to combustion force as well as tensile load due to inertia of the moving components. These loadings are cyclic in nature and the component is highly prone to fatigue failure if not deigned or manufactured carefully. Therefore connecting rods are designed and manufactured with high degree of precision for infinite loading cycle. But failures in connecting rod is often reported which is associated to either fatigue, bending, bearing failure or assembly faults. This study deals with one of such failure of connecting rod reported during fatigue testing. Failures occurred at around 1 million fatigue loading cycle as against target life of 5 million cycles. The present study represents the investigations done for engine connecting rod and with a view to identify the root cause of failure.

With the increasing need to have faster product development and yet achieve the optimum design, thrust on accurate FEA of components and system is felt. The connecting rod is an important component of the crank train and it has a significant mass contribution in multi-cylinder engine. Principal focus is directed to connecting rods having load ratio greater than or equal to 2. As the connecting rod operates in elastic range (i.e. high cycle fatigue life region) stress life approach is adopted for fatigue life evaluation. The three fold purpose of this paper is to establish an accurate FE modelling technique and analysis procedure that simulates the test conditions, aids in accurate fatigue life prediction and most importantly provides a simple procedure for virtual validation of connecting rod. To achieve this objective static strain measurement and fatigue test of connecting rod is carried out on a test bench.

Ever since mainstreaming of automobiles, engineers are focusing on making the vehicles better by means of making them more efficient, powerful and less polluting. In this study, venues of improving low end torque via improvement in volumetric efficiency as well as proper selection of turbochargers is done. An in-depth analysis of gas dynamics with respect to valve timing is studied along with the AVL Boost 1D simulation. It was found that volumetric efficiency starts to improve when there is a reduction in exhaust - exhaust valve overlap. There is an improvement found in the fresh air ratio (lambda) as the residual gas content is reduced. After the selection of valve timing, turbocharger optimization is done with comparison between two turbine sizes. Along with turbocharger comparison, technology comparison is also done namely between normal electronic VGT (Variable Geometry Turbo) (bigger turbine) and electronic VGT coupled with waste gate (smaller turbine).

This paper discusses design and optimization process for the integration of exhaust manifold with turbocharger for a 3 cylinder diesel engine, simulation activities (CAE and CFD), and validation of manifold while upgrading to meet current BS6 emissions. Exhaust after-treatment system needs to be upgraded from a simple DOC (Diesel Oxidation Catalyst) to a complex DOC+sDPF (Selective catalytic reduction coated on Diesel Particulate Filter) to meet the BS6 emission norms for this engine. To avoid thermal losses and achieve a faster light-off temperature in the catalyst, the exhaust after-treatment (EATS) system needs to be placed close to the engine - exactly at the outlet of the turbocharger. This has given to challenges in packaging the EATS. The turbocharger in case of BS4 is placed near the 2nd cylinder of the engine, but this position will not allow placing the BS6 EATS.

Lubrication systems play a major role not only in the durability of modern IC engines but also in performance and emissions. The design of the lubrication system influences the brake thermal efficiency of the engine. Also, efficient lubrication reduces the engine's CO2 emissions significantly. Thus, it is critical for an IC engine to have a well-designed lubrication system that performs efficiently at all engine operating conditions. The conventional lubrication system has a fixed-displacement oil pump that can cater to a particular speed range. However, a fully variable displacement oil pump can cater to a wide range of speeds, thereby enhancing the engine fuel efficiency as the oil flow rates can be controlled precisely based on the engine speed and load conditions. This paper primarily discusses the optimization of a lubrication system with a Variable Displacement Oil Pump (VDOP) and a map-controlled Piston Cooling Jet (PCJ) for a passenger car diesel engine.

Vehicles with manual transmission are still the most preferred choice in emerging markets like India due to their benefits in cost, simplicity and fuel economy. However, the ever-increasing vehicle population and traffic congestion demand a smooth clutch operation and a comfortable launch behaviour of any manual transmission vehicle. In the present work, the launch performance of a sports-utility vehicle (SUV) equipped with dual mass flywheel (DMF) and self-adjusting technology (SAT) clutch could be improved significantly by optimizing the clutch system. The vehicle was observed to be having a mild judder during clutch release (with 0% accelerator pedal input) in a normal 1st gear launch in flat road conditions. An extensive experimental measurement at the vehicle level could reveal the launch judder is mainly due to the 1st order excitation forces created by the geometrical inaccuracy of the internal parts of the clutch system.

In addition to performance target, recent stringent emission legislation and reduction in oil consumption are the major driving force for engine design and development. In this reference importance of crankcase ventilation has increased immensely and the manufacturers are bound to develop most efficient system with high oil trap efficiency. In crankcase ventilation system, the blow-by gases from the crankcase are routed to the intake manifold through Oil separator system. The oil separator task is to retain the oil part from the blow by gas and send it back to sump. Developing an oil separator for the engine studied here was very challenging considering double stage turbocharger which produces very fine mist of oil and is difficult to separate. The study shows that oil mist coming in blow by is of size 0.3 micron and lesser than it. The major contribution of these fine mists was from turbocharger.

Reducing the mechanical friction of internal combustion engines could play a major role in improving the brake specific fuel consumption (BSFC). Hence, it is important to reduce the friction at every component and sub-system level. In the present work, the oil pump friction of a 1.5 liter 4-cylinder diesel engine is optimized by reducing the oil pump displacement volume by 20%. This could be achieved by adopting an optimized oil supply concept which could reduce the oil leakage through the main bearings and connecting rod bearings. A 1-dimensional oil flow simulation was carried out to predict the oil flow distribution across the engine for different speeds. The results indicate that the oil leakage through the main bearings and connecting rod bearings contribute to ~25% of the total oil flow requirement of the engine. In a conventional oil supply concept, the big-end bearing of each connecting rod is connected to the adjacent main bearing through an internal oil hole.

With recent advancements to create light weight engines and therefore, to design stronger and lighter connecting rods, automobile manufacturers have looked upon vanadium micro-alloyed steels as the material of choice. These materials have been developed keeping in mind the strength and manufacturing requirements of a connecting rod. Since, 36MnVS4 has been the most popular of this category, the same has been discussed in this paper. The transition of manufacturers from the traditional C70S6 grade to the new 36MnVS4 must be dealt with in-depth study and modification of processes to adapt to new properties of the latter. C70S6 is a high carbon grade with superior fracture split whereas 36MnVS4 is a medium carbon grade with superior strength and ductility owing to the presence of vanadium.

Light weighting in modern automotive powertrains call for use of plastics (PP, PA66GF35) for cam covers, intake manifolds and style covers, and noise encapsulation covers. Conventionally, in early stage of design these components are evaluated for static assembly loads & gasket compression loads at component level. However, engine dynamic excitations which are random in nature make it challenging to evaluate these components for required fatigue life. In this paper, robust methodology to evaluate the fatigue life of engine style cover assembly for random vibration excitations is presented. The investigation is carried out in a high power-density 4-cylinder in-line diesel engine. The engine style cover (with Polyurethane foam) is mounted on cam cover and the intake manifold using steel studs and rubber isolators to suppress the radiated noise.