Search Results

Increasing combustion pressure, low viscosity oils, less oil supply and the increasing stress due to downsizing of internal combustion engines (ICE) lead to higher loads within the bearing. As the mechanical and tribological loads on the piston pin bearings have a direct impact on the service life and function of the overall engine system, it is necessary to develop a robust tribological design approach. Regarding the piston pin bearing of a diesel engine, this study aims to describe the effects of different parameters on a DLC-coated piston pin within the bearing. Therefore, an external engine part test rig, which applies various forces to the connecting rod and measures the torque on a driven pin, is used to carry out validation measurements. The special feature of the test bench is the way the piston is beared. For the first experiments, the piston crown is placed against a plate (plate-bearing); later, this plate-bearing is replaced by a hydrostatic bearing.

The influence of different port designs on the generation of a swirl flow is described on the basis of stationary and non-stationary flow analyses. Subsequently, engine test bench analyses with a 3-valve one-cylinder engine were performed to assess the aforementioned port configurations with respect to their influence on the lean-burn behaviour. The most favourable port design was then used to analyse various combustion chamber shapes in order to further improve the engine behaviour during lean-burn operation and to select the most promising combustion chamber variant. Finally, the port and combustion chamber configurations thus identified were applied in vehicle simulation tests with lean-burn and EGR-burn operation to check the emission behaviour for compliance with the future European level 3 emission limits.

The comparison of a light weight crankcase to the production cast iron crankcase of the new Mercedes Benz 2.9-liter direct injection (DI) five-cylinder turbo diesel engine with intercooler is described. The light weight crankcase is cast from the aluminum alloy A 356 while other engine components like oil pan, timing case cover and brackets are manufactured from a magnesium alloy. This paper describes the engine design with the simultaneous calculation, the mechanical development and the acoustic measurements. In this study an engine weight reduction of about 30 kg with comparable noise emission compared to the production engine with cast iron crankcase is realized.

Modern commercial vehicle engines are equipped with turbocharging and intercooling. This results in low emissions and fuel consumption. In the lower speed and load range and under transient conditions, these engines have disadvantages, as the fuel injection rate has to be limited to avoid excessive smoke emission. Also, the engine braking performance of highly charged, small displacement engines is also lower than that of large displacement engines. Mercedes-Benz decided to develop a combination of turbocharger and mechanical supercharger. In the lower speed range higher torque levels are possible and maximum torque is available without any lag especially in the transient mode with low smoke emission and fuel consumption. Vehicle performance during acceleration can be improved by up to 30%. During engine braking operation, the mechanical supercharger is activated throughout the whole engine speed range which results in a distinctive increase in braking power.

During recent years there has been a continuing increase in the demands for higher braking performance of commercial vehicle engines. Mercedes-Benz had introduced the engine brake with continuously open decompression valve (‘Konstantdrossel’) into series production in 1989 as an option (1). A further increase of braking power was to be achieved while retaining the additional decompression valve in the cylinder head. For this, the decompression valve was no longer kept open during the whole working cycle (continuously open decompression valve), but only for a short period from just before compression TDC to about 90...120° crank angle after compression TDC (pulsed decompression valve). The hydraulic actuating system which opens and closes the decompression valves was developed in cooperation with Mannesmann-Rexroth GmbH, Lohr, Germany. The engine braking performance attainable with this system is shown in comparison to other known engine braking systems.

The demand for fuel-efficient, low-displacement engines for future passenger car applications led to investigations with small DI diesel engines in the advanced engineering department at Mercedes-Benz. Single-cylinder tests were carried out to compare a 2-valve concept with 241 cm3 displacement with a 422 cm3 4-valve design, both operated with a common rail injection system. Mean effective pressures at full load were about 10 % lower with the smaller displacement. With such engines a specific power of 40 kW/I and a specific torque of about 140 Nm/I should be possible. In the current stage of optimization, penalties in fuel economy could be reduced down to values below 3 %. The “4-cylinder DI diesel engine with 1 liter displacement” is an interesting alternative to small 3 cylinder concepts with higher displacement per cylinder. An introduction into series production will not only depend on the potential for further improvement in fuel economy of such small cylinder units.

As the late combustion phase in SI engines is of high importance for a further reduction of fuel consumption and especially emissions, the impacts of unburnt mass, located in a small volume with a relatively large surface near the wall and in the top land volume, is of high relevance throughout the range of operation. To investigate and quantify the respective interactions, a state of the art Mercedes-Benz single cylinder research SI-engine was equipped with extensive measurement technology. To detect the axial and radial temperature distribution, several surface thermocouples were applied in two layers around the top land volume. As an additional reference, multiple surface thermocouples in the cylinder head complement the highly dynamic temperature measurements in the boundary zones of the combustion chamber.

Load control by means of early intake valve closing (EIVC) permits brake mean effective pressure (BMEP) to be improved by as much as 14 % at full load and pumping losses in part load to be reduced comparable to the unthrottled engine. Concomitant to this, though, the marginal conditions for good mixture formation and part load combustion optimized for efficiency are greatly impaired. With ideal mixture formation, improvements in specific part load consumption (BSFC) of the order of 8 to 12 % are achievable. The mixture formation which occurs at low part load in the combustion chamber itself is not effective as the charge motion induced by the inflow process with EIVC dies away rapidly and at the same time fuel still condenses. The inhomogeneities to which this gives rise impair ignition conditions and the combustion pattern, which greatly limits the actual useful work of the theoretical charge cycle benefit.