Search Results

This paper presents a new system for controlling the braking force between the inner and outer wheels in a turn independently. Vehicle cornering performance has improved noticeably in recent years thanks to advances achieved in tire and suspension technology. Due to this improvement, vehicle handling characteristics during braking have taken on added importance. To achieve stabler handling properties during braking in a turn, a new evaluation method is being used at Nissan to analyze vehicle directional stability. The analytical results show that decreasing the yaw moment before wheel locking occurs is effective in achieving stabler handling. An effective approach to decreasing the yaw moment is to control the braking force between the inner and outer wheels independently. Base on these analytical results and experimental data obtained with actual vehicles, a new system has been developed that provides such independent control over the braking force.

The ways in which vehicles are used in the field are continually becoming more diverse. In order to provide the optimum solution with respect to performance and weight, it is necessary to be able to assure vehicle endurance reliability with a high degree of accuracy in relation to the manner of use in each market. This situation has increased the importance of accurately quantifying the ways in which vehicles are used in the field and of designing vehicles with sufficient endurance reliability to match the usage requirements. This report presents a “market model” by which the manner of usage in the field can be treated quantitatively using combinations of environmental factors that influence the road load, drive load and corrosion load, representing typical loads vehicles must withstand.

A safety support system that uses information received from the road infrastructure is being developed in a project sponsored by the Ministry of Land, Infrastructure and Transport. The purpose of this system is to reduce the number of accidents at intersections and on highways. The system is now being tested in an experimental vehicle. This paper describes what kind of information is helpful to drivers based on the experimental results.

This paper proposes a new voice and data wireless communication method for telematics services. Data-voice (DV) modems have conventionally been used for simultaneous transmission of voice and data. With this method, however, one line is split between the data part and voice part. Lost data are retransmitted, but the voice signal is not resent because voice communication requires a real-time characteristic. The new voice and data wireless communication method proposed here switches voice to a voice line and data to a data line.

Wheels play an important role in determining the aerodynamic drag of passenger vehicles. This is because the contribution of wheels to aerodynamic drag comes from not only the wheels themselves, but also from the interference effect between wheel wakes and the base wake. As far as the authors are aware, there have been no reports about aerodynamic drag sensitivity to wheel shape factors for different vehicle types and different exterior body shapes. The purpose of this study was to clarify CD sensitivity to wheel shape factors for a sedan and an SUV, including different rear fender shapes. Many different wheel configurations were investigated in terms of the CD, base pressure and flow fields in wind tunnel tests. Multiple regression analyses were conducted to clarify CD sensitivity to each wheel shape factor based on the test data. This study revealed high CD sensitivity factors for both the sedan and SUV.

This paper deals with a vehicle detection method for realizing a blind spot warning function, under various environmental conditions. We introduced a method that is capable of discriminating the target object vehicles, under poor lighting conditions and in cases where the lens may be exposed to splashes in wet, snow and dirt roads. The image sensing of the vehicle detection consists of four functional components: obstacle detection, velocity estimation, vertical edge detection, and final classification. Such componets allow robust performances resembling geometry based approaches, with low calculation power as an apperance based approach. This paper describes the functional components, and furthermore methods to enhance the performances under low contrast conditions and also suppress false detections caused by residue on the lens, which becomes essential for installation on vehicles driven in actual road conditions.

In making driver workload assessments, it is important to evaluate the driver's level of brain activity because the operation of a motor vehicle presumably involves higher-order brain functions. Driving on narrow roads in particular probably imposes a load on the driver's brain functions because of the need to be cognizant of the tight space and to pay close attention to the surroundings. Test vehicles were fitted with a functional near-infrared spectroscopy (fNIRS) system for measuring bloodstream concentrations at 32 locations in the frontal lobe of the participating drivers in order to evaluate their levels of mental activity while driving on narrow roads. The results revealed significant increases in cerebral blood flow corresponding to the perceived workload. This suggests that increases in cerebral blood flow can be used as an effective index for estimating mental workloads.

An analysis was made of vibration phenomena in the steering system of a vehicle, when the front wheels have some amount of unbalance. The program included vehicle running tests and bench tests to ascertain some of the factors influencing vibration behavior. A mathematical model of the vibration system was simulated on a digital computer in as much detail as possible. The resultant understanding of the dynamics of the system as a whole led to an extensive theoretical analysis of selected key parameters.

Curbing emissions of carbon dioxide (CO₂), which is believed by many scientists to be a major contributor to global warming, is one of the top priority issues that must be addressed by automobile manufacturers. Automakers have set their own strategies to improve fuel economy and to reduce CO₂ emissions. Some of them include integrated approaches, focusing on not only improvement of vehicle technology, but also human factors (eco-driving support for drivers) and social and transportation factors (traffic management by intelligent transportation systems [ITS]). Among them, electric vehicles (EVs) will be a key contributor to attaining the challenging goal of CO₂ reduction. Mass deployment of EVs is required to achieve a zero-emission society. To accomplish that, new advanced technologies, new business schemes, and new partnerships are required.

After the turn of the century, growing social attention has been paid to environmental concerns, especially the reduction of greenhouse gas emissions and it comes down to a personal daily life concern which will affect the purchasing decision of vehicles in the future. Among all the sources of greenhouse gas emissions, the transportation industry is the primary target of reduction and almost every automotive company pours unprecedented amounts of money to reengineer the vehicle technologies for better fuel efficiency and reduced CO2 emission. Besides those efforts paid for sheer improvements of genuine vehicle technologies, NISSAN testified that “connectivity” with outside servers contributed a lot to reduce fuel consumption, thus the less emission of GHG, with two major factors; 1. detouring the traffic congestions with the support of probe-based real-time traffic information and 2. providing Eco-driving advices for the better driving behavior to prompt the better usage of energy.

An electric vehicle (EV) is promising as clean energy powered vehicle, due to increased interest in fuel economy and environment in recent years. However, it requires to meet unique safety performance such as electric safety. Nissan has developed a new electric vehicle which achieves electric safety in addition to maintaining enough cruising distance and cabin space. This was achieved by I he development of an all-new platform for electric vehicles. The electric safety was enhanced by the protection of high-voltage components based on consideration of component layout and body structure, high-voltage shutdown by impact sensing system and prevention of short circuit by fuse in the battery. As an example of the protection of high-voltage components, the battery which locates under the floor was protected by elaborative packaging and multi-layer protection structure.

At Nissan we have developed a new parallel hybrid system for rear-wheel-drive hybrid vehicles. As the main components of the hybrid system, both the motor and the inverter have been developed and are manufactured in house to attain high power density for providing responsive acceleration, a quiet EV drive mode and improved fuel economy. Because the motor is located between the engine and the transmission, it had to be shortened to be within the length allowed for the powertrain. Therefore, new technologies have been developed such as high-density, square-shaped windings and an optimized magnetic circuit specially designed for concentrated winding motors. The inverter is sized to a 12V battery, which it replaces in the engine compartment. Despite its compact size, the inverter must have rather large current capacity to drive a high-power motor. Heat management is critical to the design of a small but high-power inverter.

Basic vehicle performance, such as Safety, Comfort and Economy, are by dependent on tire performance, and it is the air pressure in the tire which assures this performance. However, tire air has a tendency to leak naturally, making it necessary to check them periodically. Since a deterioration in vehicle performance resulting from a drop on tire air pressure can not be directly felt by the driver, the number of people maintaining their tires sufficiently is relatively few. There have been many tire pressure warning devices developed which advise the driver when the pressure drops below a prescribed level. Differing from conventional devices, the TWD-III features a 7-step digital display (at a pitch of 0.1 kgf/cm2) which shows the pressure of each tire within an optional range, and it also has a flat tire warning function. The employment of echo effect from clystal vibrator resonance precludes the need to attach a power source on the tire.

Electric Vehicles are very quiet at low speeds therefore people (especially the visually impaired) have difficulty recognizing that these vehicles are approaching. To address this concern, Approaching Vehicle Sound for Pedestrians system development has been discussed worldwide. In Japan, USA, Europe and China, government regulation is currently under study. As a solution to meet this concern, Nissan has developed the VSP (Approaching Vehicle Sound for Pedestrians) system for implementation on Nissan's first mass production Electric Vehicle. Nissan VSP emits a futuristic sound to satisfy 3 key stakeholders' concerns; for pedestrians to provide detectability, for drivers and neighborhoods to maintain a quiet environment. The sound emitted during forward motion has a “twin peaks and one dip” frequency signature, with modulation (or rhythmic structure) to accommodate human-beings ear frequency sensitivity, hearing loss due to aging and ambient noise conditions.

The expanded application of automotive electronics in recent years has increased the number of control switches, thus necessitating the optimization of their layout around the driver and improvement in operability. As an effective means in improving operability, switches mounted on the steering wheel have been developed, placing controls closer to drivers for easier access while driving. However, since the switches rotate along with the steering wheel, recognition and operation of those switches left a few things to be desired. Recently we developed a "steering wheel with a non-rotating center switch pad" where the pad section with the switches are kept stationary. In this paper we describe the general outline of this development.

THIS PAPER presents an advanced heads-up display which has been newly developed for use in 88 Nissan Silvia model. The HUD consists of a projector with a newly developed high brightness VFD and light-selective film used as a combiner which is coated on the windshield. This combination provides good display legibility even under bright sunlight. The display shows the vehicle speed in a three-digit reading at distance of more than one meter from the driver's eyes. The windshield-coated combiner conforms to U.S. safety standards concerning light transmittance, abrasion and other performance requirements. Experimental data are also presented which substantiate the HUD's high legibility and confirm its effect in enhancing the driver's attention toward the road ahead

This paper describes a new approach to solving various problems inherent in conventional multiplexed wiring systems. These problems include the fact that the quantity of cut leads, which determines the cost, is not reduced even though the bulk of the wire harness is decreased. Another problem is that the communications system has a very complex configuration. With the approach proposed here it has been found that the number of cut leads can be reduced by housing the communications circuits individually in each piece of electrical equipment. This can be accomplished by grouping together the wiring in which the signals activating electrical load units all flow in the same direction. Custom LSI circuits have been developed to simplify the communications circuits. All of these developments have been combined into practical multiplexed wiring systems for controlling the power Windows, automatic door locks and power seats.

This paper describes a headway distance control system for platoon driving on an automated highway system (AHS). The system implemented on a test vehicle is described first, followed by a description of a vehicle control method based on the use of throttle and brake actuators. This method makes it possible to obtain the target acceleration and deceleration regardless of the vehicle speed range and the rate of acceleration or deceleration. Experimental and simulation results obtained with this method are presented. A control method is then described that uses inter-vehicle communication and laser radar to maintain a constant headway between vehicles. The results of simulations and driving tests conducted with three vehicles are presented to illustrate that the use of inter-vehicle communication is highly effective in improving headway control performance.

This paper presents a lightweight, high-performance Lithium-ion Battery System developed jointly by Nissan Motor Co. and Sony Corp. for electric vehicle (EV) use. Electric vehicles are generally powered by a battery pack consisting of numerous cells connected in a series. Management techniques to elicit the maximum performance of the battery pack are needed, including a function for monitoring individual cells to prevent them from over-discharging. Because of high cell voltage, lithium-ion batteries enable the number of cells in a battery pack to be greatly reduced compared with other types of battery systems. They also allow accurate detection of the battery State of Charge (SOC) based on the battery voltage. These characteristics are conducive to the application of battery pack management technology. These concepts provided the basis for the development of a Lithium-ion Battery System for EV application.

This paper describes a high-power lithium-ion battery system that has been newly developed for application to hybrid electric vehicles (HEVs). The battery system was designed on the premise of an underfloor location so as to avoid sacrificing interior spaciousness while providing the power output and recharge performance required by the hybrid propulsion system. To meet these requirements, efforts were made to increase the specific power and to reduce the heat generation of the battery to previously unattained levels. As a result, exceptionally high specific power of 1,200 W/kg per cell, battery pack power of 25kW at 20% state of charge (SOC), and high charge/discharge efficiency of more than 95% in the urban driving schedule has been achieved. The battery pack is composed of two box-shaped modules designed with a low height in consideration of underfloor mountability.