Search Results

In this paper, HCCI combustion characteristics of three typical high octane number fuels, gasoline, ethanol and methanol, are compared in a Ricardo single cylinder port injection engine with compression ratio of 10.5. In order to trap enough high temperature residual gas to heat intake mixture charge for stable HCCI combustion, camshafts of the experimental engine are replaced by a set of special camshafts with low valve lift and short cam duration. The three fuels are injected into the intake port respectively in different mixture volume percentages, which are E0 (100% gasoline), E50 (50% gasoline, 50% ethanol), E100 (100% ethanol), M50 (50% gasoline, 50% methanol) and M100 (100% methanol). This work concentrates on the combustion and emission characteristics and the available HCCI operation range of these fuels. What's more, the detailed comparison of in-cylinder temperature, ignition timing and other parameters has been carried out.

The effects of cooled EGR on combustion and emission characteristics in HCCI operation region was investigated on a single-cylinder diesel engine, which is fitted with port injection of DME and methanol. The results indicate that EGR rate can enlarge controlled HCCI operating region, but it has little effect on the maximum load of HCCI engine fuelled with DME/methanol dual-fuels. With the increase of EGR rate, the main combustion ignition timing (MCIT) delays, the main combustion duration (MCD) prolongs, and the peak cylinder pressure and the peak rate of heat release decreases. Compared with EGR, DME percentage has an opposite effect on HCCI combustion characteristics. The increase of indicated thermal efficiency is a combined effect of EGR rate and DME percentage. Both HC and CO emissions ascend with EGR rate increasing, and decrease with DME percentage increasing. In normal combustion, NOX emissions are near zero.

Effects of fuel physical and chemical properties on combustion and emissions were investigated on both metal and optical diesel engines. The new generation oxygenated biofuels, n-butanol and DMF (2,5-dimethylfuran) were blended into diesel fuel with 20% volume fraction and termed as Butanol20 and DMF20 respectively. The exhaust gas recirculation (EGR) rates were varied from zero to ∼60% covering both conventional and low temperature combustion. Meanwhile, the reference fuels such as n-heptane, cetane, and iso-cetane were also used to isolate the effects of different fuel properties on combustion and emissions. In addition, to clarify the effects of oxygenated structures on combustion and emissions, a fundamental partially premixed burner was also used. Results based on metal and optical diesel engines show that fuel cetane number is the dominated factor to affect the auto-ignition timing and subsequent combustion process.

The effects of Exhaust Gas Recirculation (EGR) and octane number of PRF fuel on combustion and emission characteristics in HCCI operation were investigated. The results show that EGR could delay the ignition timing, slow down the combustion reaction rate, reduce the pressure and average temperature in cylinder and extend the operation region into large load mode. With the increase of the fuel/air equivalence ratio or the fuel octane number (ON), the effect of EGR on combustion efficiency improves. With the increase of EGR rate, the combustion efficiency decreases. The optimum indicated thermal efficiency of different octane number fuels appears in the region of high EGR rate and large fuel/air equivalence ratio, which is next to the boundary of knocking. In the region of high EGR rate, HC emissions rise up sharply as the EGR rate increases. With the increase of octane number, this tendency becomes more obvious.

Diesel-fueled HCCI combustion was achieved by multi-pulse injection before top dead center (TDC). However, the multi-pulse injections strategies have not been sufficiently studied previously due to the large number of parameters to be considered. In the present work, a series of multi-pulse injection modes with four or five pulses in each mode are designed, and their effects on diesel HCCI Combustion are experimentally studied. The results showed that the HCCI diesel combustion was extremely sensitive to injection mode. There were many modes to achieve very low NOx and smoke emissions, but the injection parameters of these modes must be optimized for higher thermal efficiency. A micro-genetic algorithm coupled with a modified 3D engine simulation code is utilized to optimize the injection parameters including the injection pressure, start-of-first-injection timing (SOI), fuel mass in each pulse injection and dwell time between consecutive pulse injections.

A concept of high density-low temperature combustion (HD-LTC) is put forward in this paper, showing potential of its high thermal efficiency and very low engine-out emissions by engine experimental and CFD modeling study. A single cylinder test engine has been built-up equipped with mechanisms of variable boost pressure and intake valve closing timing (IVCT). By delaying IVCT and raising boost pressure to certain values according to engine loads, the in-cylinder charge density is regulated much higher than in conventional engines. It is found that the high charge density can play the role of rising of heat capacity as exhaust gas recirculation (EGR) does. Thereby low temperature combustion is realized with less EGR (about 18~19% oxygen concentration) to achieve very low NOx and soot emissions, which is extremely important at high and full loads.

The effect of a new exhaust catalyst system consisting of the traditional three way catalyst converter (TWC) and adsorber-reduction catalyst converter along the emission systems has been investigated in this research under different schemes of catalyst converter arrangement and different ranges of engine speed and engine load. The effect on BSFC (Brake Specific Fuel Consumption) of a lean burn gasoline engine has also been studied at the same time. The upstream placement of TWC ahead of the NOx Adsorber Catalyst has been selected, which is corresponding to the highest NOx converting efficiency. The effect of engine speed on the exhaust emission and BSFC is related to absolute time and the ratio of lean burn time to rich burn time. Engine load is the major factor in affecting exhaust emission characteristics and BSFC of lean burn gasoline engine.

Homogeneous Charge Compression Ignition (HCCI) has the potential of reducing fuel consumption as well as NOx emissions. However, it is still confronted with problems in real-time control system and control strategy for the application of HCCI, which are studied in detail in this paper. A CAN-bus-based distributed HCCI control system was designed to implement a layered close loop control for HCCI gasoline engine equipped with 4VVAS. Meanwhile, a layered management strategy was developed to achieve high real-time control as well as to simplify the couplings between the inputs and the outputs. The entire control system was stratified into three layers, which are responsible for load (IMEP) management; combustion phase (CA50) control and mechanical system control respectively, each with its own specified close loop control strategy. The system is outstanding for its explicit configuration, easy actualization and robust performance.

With the application of valve timing strategy to inlet and exhaust valves, Homogeneous Charge Compression Ignition (HCCI) combustion was achieved by varying the amount of trapped residuals through negative valve overlap on a Ricardo Hydra four-stroke port fuel injection engine fueled with ethanol. The effect of ethanol on HCCI combustion and emission characteristics at different air-fuel ratios, speeds and valve timings was investigated. The results indicate that HCCI ethanol combustion can be achieved through changing inlet and exhaust valve timings. HCCI ethanol combustion range can be expanded to high speeds and lean burn mixture. Meanwhile, the factors influencing ignition timing and combustion duration are valve timing, lambda and speeds. Moreover, NOx emissions are extremely low under HCCI combustion. The emissions-speed and emissions-lambda relationships are obtained and analyzed.