Search Results

The centrifugal compressor is one of the most commonly used air compressors for fuel cell air supply systems, and it has the small volume, high pressure ratio and low noise. However, surge in a centrifugal compressor severely limits its stable flow range. In this paper, a mathematical model of the compressor aerodynamic performance based on the energy transfer method was established, some parameters of model were identified by experimental data, and the model was validated through experiments. Then the dynamic model of the compression system was derived based on the compressor model and the Moore-Greitzer model. The stability analysis of the compression system was conducted, and it was strictly proved that when the compression system is unstable, there is the limit cycle in this nonlinear system, namely the surge cycle. Furthermore, the simulation of the compression system was conducted and the instability condition of the compression system was presented.

Beamforming techniques are widely used today in aeroacoustic wind tunnels to identify wind noise sources generated by interaction between incoming flow and the test object. In this study, a planar spiral microphone array with 120 channels was set out-of-flow at 1:1 aeroacoustic wind tunnel of Shanghai Automotive Wind Tunnel Center (SAWTC) to test exterior wind noise sources of a production car. Simultaneously, 2 reference microphones were set in vehicle interior to record potential sound source signal near the left side view mirror triangle and the signal of driver’s ear position synchronously. In addition, a spherical array with 48 channels was set inside the vehicle to identify interior noise sources synchronously as well. With different correlation methods and an advanced algorithm CLEAN-SC, the ranking of contributions of vehicle exterior wind noise sources to interested interior noise locations was accomplished.

The aftertreatment system is indispensable for the removal of the noxious pollutants emitted by diesel engines, whose efficiency depends largely on the exhaust gas temperature. Therefore, this study proposes a thermal management strategy including post injection, intake throttling and late post injection to improve the efficiency of the aftertreatment system for a heavy-duty diesel engine. In the experiments, the effects of main injection, post injection, injection pressure and throttle opening on the exhaust gas temperature at diesel oxidation catalyst (DOC) inlet were studied, with the influence of late post injection on the exhaust gas temperature at DOC outlet also investigated. The results showed that the reasonable control of throttle opening and post injection (such as the adjustment of injection timing and injection quantity) can significantly improve the average temperature at DOC inlet from 237.8°C to 333.6°C in the WHTC, with an increase of 40.3%.

With the introduction of BroadR-Reach and time-sensitive networking (TSN), Ethernet has become an option for in-vehicle networks (IVNs). Although it has been used in the IT field for decades, it is a new technology for automotive, and thus requires extensive testing. Current test solutions usually target specifications rather than the in-vehicle environment, which means that some properties are still uncertain for in-vehicle usage (e.g., fault tolerance for shorted or open wires). However, these characteristics must be cleared before applying Ethernet in IVNs, because of stringent vehicular safety requirements. Because CAN is usually used for these environments, automotive Ethernet is expected to have the same or better level of fault tolerance. Both CAN and BroadR-Reach use a single pair of twisted wires for physical media; thus, the traditional fault-tolerance test method can be applied for automotive Ethernet.

Permanent magnet synchronous motors (PMSM) are widely used in the electric vehicles for their high power density and high energy efficiency. And the motor control system for electric vehicles is one of the most critical safety related systems in electric vehicles, because potential failures of this system can lead to serious harm to humans’ body, so normally a high automotive safety integrity level (ASIL) will be assigned to this system. In this paper, an ASIL-C motor control system based on a multicore microcontroller is presented. At the same time, due to the increasing number of connectivity on the vehicle, secure onboard communication conformed to the AUTOSAR standard is also implemented in the system to prevent external attacks.

Based on a 125cm3 single cylinder SI engine, the designated idle speed was controlled by adjusting of cycle ignition advance angle. By analyzing the effects of different idle speed and throttle open position on three way catalyst (TWC) light-off time and conversion efficiency of HC and CO emissions, combined with the corresponding total HC and CO emissions level, the optimum idle speed and throttle open position at engine's warm-up phase were found by the matching optimum. The present method for engine control strategy is helpful to optimize the warm-up phase emission levels in SI engine with LPG fuel.

With the increasing concern on environmental pollution and CO2 emission all over the world, range-extended electrical vehicle (REEV) has gradually got more attention because it could avoid the mileage anxiety of the battery electrical vehicles (BEV) and get high energy efficiency. Nevertheless, NVH performance of internal combustion engine range extender (ICRE) is a critical problem that affects the driving experiences for REEV. In this paper, a two-cylinder PFI gasoline engine and a permanent magnet synchronous motor (PMSM) are coaxially mounted to run as an ICRE. The ICRE control system was established based on Compact RIO hardware and LabVIEW, who has the functions of the intake throttle PID closed-loop control, autonomous ICRE operation control, and speed PID closed-loop control. In this paper, the gasoline engine was first driven to the idle condition by PMSM in speed-control mode.

Based on the basic structure and operating function of engine throttle, according to the actual structure of throttle, a 3-dimensional air transient flow is simulated to realize throttle rotated from closed position to opened position by using CFD moving mesh technology and user defined program. By applying CFD and CAA coupling method, the influence of the movement of throttle on air flow and flow-induced noise process are studied, the transient opening process is studied and analyzed. The velocity field, pressure field and the principle of flow-induced noise are analyzed under different rotational angle velocity of throttle.

The formation is a crucial step in the production process of lithium-ion batteries (LIBs), during which the solid electrolyte interphase (SEI) is formed on the surface of the anode particles to passivate the electrode. It determines the performance of the battery, including its capacity and lifetime. A meticulously designed formation protocol is essential to regulate and optimize the stability of the SEI, ultimately achieving the optimal performance of the battery. Current research on formation protocols in lithium-ion batteries primarily focuses on temperature, current, and voltage windows. However, there has been limited investigation into the influence of different initial pressures on the formation process, and the evolution of cell pressure during formation remains unclear. In this study, a pressure-assisted formation device for lithium-ion pouch cells is developed, equipped with pressure sensors.

With the increasing worldwide concern on environmental pollution, battery electrical vehicles (BEV) have attracted a lot attention. However, it still couldn’t satisfy the market requirements because of the low battery power density, high cost and long charging time. The range-extended electrical vehicle (REEV) got more attention because it could avoid the mileage anxiety of the BEVs with lower cost and potentially higher efficiency. When internal combustion engine (ICE) works as the power source of range extender (RE) for REEV, its NVH, emissions in starting process need to be optimized. In this paper, a 2-cylinder PFI gasoline engine and a permanent magnet synchronous motor (PMSM) are coaxially connected. Meanwhile, batteries and load systems were equipped. The RE co-control system was developed based on Compact RIO (Compact Reconfigurable IO), Labview and motor control unit (MCU).

Based on the basic structure and operation function of engine throttle, according to the actual structure of a throttle, a 3-dimensional simulation of the transient airflow during the rotation of the throttle from the closed position to the fully open position is realized by using CFD together with the moving mesh technology and the user-defined program. The influence of the throttle movement on the airflow process is studied. The velocity field, pressure field, and flow noise field are analyzed at different angles of throttle rotation. The numerical simulation results show that at the beginning period of the throttle rotation, the vortex appears in the flow field behind the throttle, and the drop of the air pressure between the upstream and downstream position of the throttle is sharp.

Lane Keeping Assistance (LKA) system is a very important part in Advanced Driver Assistance Systems (ADAS). It prevents a vehicle from departing out of the lane by exerting intervention. But an inappropriate performance during LKA intervention makes driver feel uncomfortable. The intervention of LKA can be divided into 3 parts: intervention timing, intervention process and intervention ending. Many researches have studied about the intervention timing and ending, but factors during intervention process also affect driver feelings a lot, such as yaw rate and steering wheel velocity. To increase driver’s acceptance of LKA, objective and subjective tests were designed and conducted to explore important indices which are highly correlated with the driver feelings. Different kinds of LKA controller control intervention process in different ways. Therefore, it’s very important to describe the intervention process uniformly and objectively.