Search Results

In a recent study, quantitative measurements were presented of in-cylinder spatial distributions of mixture equivalence ratio in a single-cylinder light-duty optical diesel engine, operated with a non-reactive mixture at conditions similar to an early injection low-temperature combustion mode. In the experiments a planar laser-induced fluorescence (PLIF) methodology was used to obtain local mixture equivalence ratio values based on a diesel fuel surrogate (75% n-heptane, 25% iso-octane), with a small fraction of toluene as fluorescing tracer (0.5% by mass). Significant changes in the mixture's structure and composition at the walls were observed due to increased charge motion at high swirl and injection pressure levels. This suggested a non-negligible impact on wall heat transfer and, ultimately, on efficiency and engine-out emissions.

We have developed a methodology for predicting combustion and emissions in a Homogeneous Charge Compression Ignition (HCCI) Engine. The methodology judiciously uses a fluid mechanics code followed by a chemical kinetics code to achieve great reduction in the computational requirements; to a level that can be handled with current computers. In previous papers, our sequential, multi-zone methodology has been applied to HCCI combustion of short-chain hydrocarbons (natural gas and propane). Applying the same procedure to long-chain hydrocarbons (iso-octane) results in unacceptably long computational time. In this paper, we show how the computational time can be made acceptable by developing a segregated solver. This reduces the run time of a ten-zone problem by an order of magnitude and thus makes it much more practical to make combustion studies of long-chain hydrocarbons.

An ongoing goal of the Powertrain Control Research Laboratory (PCRL) at the University of Wisconsin-Madison has been to expand and improve the ability of the single cylinder internal combustion research engine to represent its multi-cylinder engine counterpart. To date, the PCRL single cylinder engine test system is able to replicate both the rotational dynamics (SAE #2004-01-0305) and intake manifold dynamics (SAE #2006-01-1074) of a multi cylinder engine using a single cylinder research engine. Another area of interest is the replication of multi-cylinder engine cold start emissions data with a single-cylinder engine test system. For this replication to occur, the single-cylinder engine must experience heat transfer to the engine coolant as if it were part of a multi-cylinder engine, in addition to the other multi-cylinder engine transient effects.

Diesel piston bowl geometry can affect turbulent mixing and therefore it impacts heat-release rates, thermal efficiency, and soot emissions. The focus of this work is on the effects of bowl geometry and injection timing on turbulent flow structure. This computational study compares engine behavior with two pistons representing competing approaches to combustion chamber design: a conventional, re-entrant piston bowl and a stepped-lip piston bowl. Three-dimensional computational fluid dynamics (CFD) simulations are performed for a part-load, conventional diesel combustion operating point with a pilot-main injection strategy under non-combusting conditions. Two injection timings are simulated based on experimental findings: an injection timing for which the stepped-lip piston enables significant efficiency and emissions benefits, and an injection timing with diminished benefits compared to the conventional, re-entrant piston.

The University of Wisconsin - Madison Hybrid Vehicle Team has designed, fabricated, tested and optimized a four-wheel drive, charge sustaining, split-parallel hybrid-electric crossover vehicle for entry into the 2006 Challenge X competition. This multi-year project is based on a 2005 Chevrolet Equinox platform. Trade-offs in fuel economy, greenhouse gas impact (GHGI), acceleration, component packaging and consumer acceptability were weighed to establish Wisconsin's Vehicle Technical Specifications (VTS). Wisconsin's Equinox, nicknamed the Moovada, utilizes a General Motors (GM) 110 kW 1.9 L CIDI engine coupled to GM's 6-speed F40 transmission. The rear axle is powered by a 65 kW Ballard induction motor/gearbox powered from a 44-module (317 volts nominal) Johnson Controls Inc., nickel-metal hydride hybrid battery pack. It includes a newly developed proprietary battery management algorithm which broadcasts the battery's state of charge onto the CAN network.

Off-highway mining and construction equipment typically converts all the power output of the engine to hydraulic power, with this power then used to perform the earth-moving operations, and also to propel the vehicle. This equipment presents significant opportunities for a new type of powerplant designed to deliver hydraulic power directly. An alternative to the conventional engine driven pump is a free-piston engine-pump (FPEP). The FPEP incorporates the functions of both an internal combustion engine and a hydraulic pump into a single, less-complex unit. The design presented in this paper utilizes two double-ended, reciprocating, opposed pistons, with combustion at one end of each piston and pumping at the opposite end. The opposed piston layout provides balance and also facilitates uniflow scavenging through intake and exhaust ports in the combustion section of the engine. An important feature of this FPEP design is the rebound accumulator circuit.

Using a low-speed high-torque (LSHT) pump/motor to provide the speed range and torque for a hydrostatic automobile offers a number of advantages over using a high-speed low-torque pump/motor, combined with a gear reducer. However, there appear to be no LSHT units commercially available that have true variable displacement capability. Because of this void, a variable displacement pump/motor has been designed and built that could provide a direct drive for each wheel of a hydrostatic automobile. The unit uses some components such as the cylinder block, piston and modified rotating case from a commercially available radial piston pump/motor. Initial preliminary testing of the pump/motor indicates that it has good efficiency and performance characteristics, and, with further development should be very attractive for automotive use. This paper focuses on the design and kinematics of the device.

A direct calibration has been performed on laser-induced fluorescence measurements of the oil film in a single cylinder air-cooled research engine by simultaneously measuring the minimum oil film thickness by the capacitance technique. At the minimum oil film thickness the capacitance technique provides an accurate measure of the ring-wall distance, and this value is used as a reference for the photomultiplier voltage, giving a calibration coefficient. This calibration coefficient directly accounts for the effect of temperature on the fluorescent properties of the constituents of the oil which are photoactive. The inability to accurately know the temperature of the oil has limited the utility of off-engine calibration techniques. Data are presented for the engine under motoring conditions at speeds from 800 - 2400 rpm and under varying throttle positions.

Two different types of mesh used for diesel combustion with the KIVA-4 code are compared. One is a well established conventional KIVA-3 type polar mesh. The other is a non-polar mesh with uniform size throughout the piston bowl so as to reduce the number of cells and to improve the quality of the cell shapes around the cylinder axis which can contain many fuel droplets that affect prediction accuracy and the computational time. This mesh is specialized for the KIVA-4 code which employs an unstructured mesh. To prevent dramatic changes in spray penetration caused by the difference in cell size between the two types of mesh, a recently developed spray model which reduces mesh dependency of the droplet behavior has been implemented. For the ignition and combustion models, the Shell model and characteristic time combustion (CTC) model are employed.

This research explored methods to reduce regulated emissions in a small-bore, direct-injection diesel engine. Swirl was used to influence mixing of the spray plumes, and alternative fuels were used to study the effects of oxygenated and water microemulsion diesel fuels on emissions. Air/fuel mixing enhancement was achieved in the running engine by blocking off a percentage of one of the two intake ports. The swirl was characterized at steady-state conditions with a flowbench and swirl meter. Swirl ratios of 1.85, 2.70, and 3.29 were studied in the engine tests at full load with engine speeds of 1303, 1757, and 1906 rev/min. Increased swirl was shown to have negative effects on emissions due to plume-to-plume interactions. Blends of No. 2 diesel and biodiesel were used to investigate the presence of oxygen in the fuel and its effects on regulated emissions. Pure No. 2 diesel fuel, a 15% and a 30% biodiesel blend (by weight) were used.

Studies on the effects of methyl soyate (biodiesel) blends with #2 diesel fuel in conjunction with various high pressure injection schemes were conducted on a single cylinder version of the Caterpillar 3400 series heavy duty diesel engine. Engine operating conditions at both high and low loads were investigated. Experiments were performed over a range of injection timings allowing particulate versus NOx trade-off curves to be generated. Phillips 66 certified #2 diesel fuel was used as the baseline; mixtures of 20% and 40% by volume of methyl soyate with the baseline fuel were used as the biodiesel blends. A blend of 20% by volume octadecene (a hydrocarbon fuel that is representative of the biodiesel hydrocarbon's composition but without the oxygen) in #2 diesel fuel was also investigated to help determine the mechanisms of emissions reduction.

Opposed-piston 2-stroke (OP-2S) engines have the potential to achieve higher thermal efficiency than a typical diesel engine. However, the uniflow scavenging process is difficult to control over a wide range of speeds and loads. Scavenging performance is highly sensitive to pressure dynamics, port timings, and port design. This study proposes an analysis of the effects of port vane angle on the scavenging performance of an opposed-piston 2-stroke engine via simulation. A CFD model of a three-cylinder opposed-piston 2-stroke was developed and validated against experimental data collected by Achates Power Inc. One of the three cylinders was then isolated in a new model and simulated using cycle-averaged and cylinder-averaged initial/boundary conditions. This isolated cylinder model was used to efficiently sweep port angles from 12 degrees to 29 degrees at different pressure ratios.

In this paper results are given from single-cylinder, steady-state engine tests using the Texaco Diesel Additive (TDA) as an in-fuel emission reducing agent. The data include NOx, total unburned hydrocarbons, indicated specific fuel consumption, and heat release analysis for one engine speed (1500 RPM) with two different loads (Φ ≈ 0.3, IMEP = 0.654 MPa and Φ ≈ 0.5, IMEP = 1.006 MPa) using the baseline fuel and fuels with one percent and five percent additive by weight. The emissions were measured in the exhaust stream of a modified TACOM-LABECO single cylinder engine. This engine is a 114 mm x 114 mm (4.5″ x 4.5″) open chamber low swirl design with a 110.5 MPa (16,000 psi) peak pressure Bosch injector. The injector has 8 holes, each of 0.2 mm diameter. The intake air was slightly boosted (approximately 171 kPa (25 psia)) and slightly heated (333 K (140 °F)). In previous research on this engine the emissions, including soot, were well documented.

Fuel film temperature and thickness were measured on the piston crown of a DISI engine under both motored and fired conditions using the fiber-based laser-induced fluorescence method wherein a single fiber delivers the excitation light and collects the fluorescence. The fibers were installed in the piston crown of a Bowditch-type optical engine and exited via the mirror passage. The fuel used for the fuel film temperature measurement was a 2×10-6 M solution of BTBP in isooctane. The ratio of the fluorescence intensity at 515 to that at 532 nm was found to be directly, but not linearly, related to temperature when excited at 488 nm. Effects related to the solvent, solution aging and bleaching were investigated. The measured fuel film temperature was found to closely follow the piston crown metal temperature, which was measured with a thermocouple.

Many recent studies have shown that the Reactivity Controlled Compression Ignition (RCCI) combustion strategy can achieve high efficiency with low emissions. However, it has also been revealed that RCCI combustion is difficult at high loads due to its premixed nature. To operate at moderate to high loads with gasoline/diesel dual fuel, high amounts of EGR or an ultra low compression ratio have shown to be required. Considering that both of these approaches inherently lower thermodynamic efficiency, in this study natural gas was utilized as a replacement for gasoline as the low-reactivity fuel. Due to the lower reactivity (i.e., higher octane number) of natural gas compared to gasoline, it was hypothesized to be a better fuel for RCCI combustion, in which a large reactivity gradient between the two fuels is beneficial in controlling the maximum pressure rise rate.

The contribution to the engine-out hydrocarbon (HC) emissions from fuel that escapes the main combustion event in piston ring crevices was estimated for an air-cooled, V-twin utility engine. The engine was run with a homogeneous pre-vaporized mixture system that avoids the presence of liquid films in the cylinder, and their resulting contribution to the HC emissions. A simplified ring pack gas flow model was used to estimate the ring pack contribution to HC emissions; the model was tested against the experimentally measured blowby. At high load conditions the model shows that the ring pack returns to the cylinder a mass of HC that exceeds that observed in the exhaust, and thus, is the dominant contributor to HC emissions. At light loads, however, the model predicts less HC mass returned from the ring pack than is observed in the exhaust. Time-resolved HC measurements were performed and used to assess the effect of combustion quality on HC emissions.

Velocity measurements have been made in a motored engine intended for direct injection spark ignited (DISI) operation. Previous experiments showed the effect of intake gas velocities on direct injection spray plumes in this engine, without directly quantifying the gas velocities involved. This work documents the intake velocities in the vicinity of the spray plume, although the spray was not present in these experiments. The measurements were made using an LDV system. Two velocity components were measured, though not simultaneously, through two orthogonal windows in the cylinder of an optical engine equipped with a head designed for DISI engine use. This engine had 4-valves and a pent-roof; the injector (when installed) was positioned slightly off-center in the head, with the spark plug located near by.

Intake port and cylinder flow have been modeled for a dual intake valve diesel engine. A block structured grid was used to represent the complex geometry of the intake port, valves, and cylinder. The calculations were made using a pre-release version of the KIVA-3 code developed at Los Alamos National Laboratories. Both steady flow-bench and unsteady intake calculations were made. In the flow bench configuration, the valves were stationary in a fully open position and pressure boundary conditions were implemented at the domain inlet and outlet. Detailed structure of the in-cylinder flow field set up by the intake flow was studied. Three dimensional particle trace streamlines reveal a complex flow structure that is not readily described by global parameters such as swirl or tumble. Streamlines constrained to lie in planes normal to the cylinder axis show dual vortical structures, which originated at the valves, merging into a single structure downstream.

Fuel-borne catalysts (FBC) have demonstrated efficacy as an important strategy for integrated diesel emission control. The research summarized herein provides new methodologies for the characterization of engine-out speciated emissions. These analytical tools provide new insights on the mode of action and chemical forms of metal emissions arising from use of a platinum and cerium based commercial FBC, both with and without a catalyzed diesel particulate filter. Characterization efforts addressed metal solubility (water, methanol and dichloromethane) and particle size and charge of the target species in the water and solvent extracts. Platinum and cerium species were quantified using state-of-the-art high resolution plasma mass spectrometry. Liquid-chromatography-triple quad mass spectrometry techniques were developed to quantify potential parent Pt-FBC in the PM extracts. Speciation was examined for emissions from cold and warm engine cycles collected from an engine dynamometer.

This work experimentally investigates the impact of premixed fuel composition (methane/ethane, methane/propane, and methane/hydrogen mixtures having equivalent chemical energy) and pilot reactivity (cetane number) on diesel-pilot injection (DPI) combustion performance and emissions, with an emphasis on the pilot ignition delay (ID). To support the experimental pilot ignition delay trends, an analysis technique known as Mixing Line Concept (MLC) was adopted, where the cold diesel surrogate and hot premixed charge are envisioned to mix in a 0-D constant volume reactor to account for DPI mixture stratification. The results show that the dominant effect on pilot ignition is the pilot fuel cetane number, and that the premixed fuel composition plays a minor role. There is some indication of a physical effect on ignition for cases containing premixed hydrogen.