Search Results

Carbon canisters have been adapted for automobile use since the early 1970s to control evaporative emissions. Stringent emission regulations and the requirement for an enhanced evaporative emissions test procedure, make this an important issue. The air and evaporative fuel from the carbon canister therefore need important consideration with respect to air to fuel ratio (AFR) control and idle by-pass air control. Although a few complex models of the activated carbon canister have been developed, a control-oriented, simplistic carbon canister model needs to be developed. This paper explores the control-oriented modeling of a canister purge air system along with the on-line estimation of evaporative fuel loading of the activated carbon. An attempt was made at providing an analytical expression for the evaporative fuel and air entering the intake manifold.

A fuel vapor system model (FVSMOD) has been developed to simulate vehicle evaporative emission control system behavior. The fuel system components incorporated into the model include the fuel tank and pump, filler cap, liquid supply and return lines, fuel rail, vent valves, vent line, carbon canister and purge line. The system is modeled as a vented system of liquid fuel and vapor in equilibrium, subject to a thermal environment characterized by underhood and underbody temperatures and heat transfer parameters assumed known or determined by calibration with experimental liquid temperature data. The vapor/liquid equilibrium is calculated by simple empirical equations which take into account the weathering of the fuel, while the canister is modeled as a 1-dimensional unsteady absorptive and diffusive bed. Both fuel and canister submodels have been described in previous publications. This paper presents the system equations along with validation against experimental data.

A proof-of-concept study has been undertaken to demonstrate the use and potential benefits of actively controlled coolant jets in an IC engine cooling gallery simulator. Results have shown that substantial reductions in coolant volumes are possible and that the control of the liquid/metal surface temperature can be achieved within +/- 0.2°C in response to transient heat flux conditions.

Due to the stringent emission regulations, On-Board Diagnostics II (OBD II) and the requirement of enhanced evaporative emissions test procedure, an aggressive canister purge control strategy is required for automotive vehicles. The enhanced evaporative emissions test procedure has forced car manufacturer to purge the carbon canister in the vehicle idle condition so that production vehicles meet the SHED and hot soak test requirements. This not only worsens the idle speed quality but also tends to increase exhaust emission levels. Using analytical models of evaporative air and fuel, feed-forward control strategy for both idle by-pass air and air to fuel ratio can be improved. This paper demonstrates an application of evaporative system modeling to the idle air and air to fuel ratio control.

The Curtain Airbag (CAB) is used currently to provide head and neck protection for the front-seat and rear-seat vehicle occupants during side-impact collisions and vehicle rollovers. The coated fabric materials are used in CABs for occupant protection in side impact and rollover events. In this paper the design and development study of CABs is described by using simulation and physical tests. The mechanical properties for the airbag material are determined by uniaxial test in the fill and warp directions. Shear strength is also evaluated by using the uniaxial test, but the specimen is cut along 45° angle. These test values are used in the finite element (FE) simulations. In this paper, a methodology of the design study is discussed. A Free Motion Headform (FMH) impacting a pole with a pillow shaped airbag is used in the design study. The influences of CAB design parameters such as pressure, chamber width, impact speed and hit location are evaluated.

The recycling of post industrial ABS and PMMA was investigated. A material compound consisting of 100% post industrial (PI) recycled ABS and multicolored acrylic (PMMA) scrap from a manufacturing plants was blended and extruded. Test samples were injection molded and the test results were correlated to virgin material. Additionally, the material was used in injection molding of rear lamp housings in black and gray colors. The test results and economics are promising.

The development and preliminary testing of an algorithm that detects impending rollover is described. The algorithm is intended for use in conjunction with active chassis systems to prevent some types of rollovers. Several methods of estimating roll angle and roll rate from physical principles using available sensors are presented. Advantages and drawbacks of each method and their ranges of reliable operations are discussed. An approach using a closed-loop adaptive observer for estimating roll angle and roll rate of vehicle body with respect to the road is proposed. Performance and robustness of the estimator are evaluated through numerical simulations and vehicle testing, using various scenarios, including maneuver induced and road induced body roll. The estimates are shown to be consistently superior to those obtained from other methods. A roll index is proposed, which uses the estimated roll angle and other signals to indicate rollover danger.

In order to allow continued production of the AM General Optimizer 6500 during MY 2007 through 2010 this IDI engine (Indirect Injection - swirl chamber) requires sophisticated aftertreatment controls while maintaining its fuel economy and durability. The main purpose of the development program was to retain the relatively inexpensive and simple base engine with distributor pump and waste-gated turbocharger, while adding hardware and software components that allow achievement of the phase-in emission standards for 2007 through 2010. The aftertreatment system consists of Diesel Oxidation Catalyst (DOC), NOx Adsorber Catalyst (or DeNOx Trap - DNT) and Diesel Particle Filter (DPF). In addition to the base hardware, an intake air throttle valve and an in-exhaust fuel injector were installed. The presented work will document the development process for a 2004 certified 6.5 l IDI heavy-duty diesel engine to comply with the 2007 heavy-duty emission standards.

The focus of this study is to determine the effect of using B-20 (a blend of 20% soybean methyl ester biodiesel and 80% ultra low sulfur diesel fuel) on the combustion process, performance and exhaust emissions in a High Speed Direct Injection (HSDI) diesel engine equipped with a common rail injection system. The engine was operated under simulated turbocharged conditions with 3-bar indicated mean effective pressure and 1500 rpm engine speed. The experiments covered a wide range of injection pressures and EGR rates. The rate of heat release trace has been analyzed in details to determine the effect of the properties of biodiesel on auto ignition and combustion processes and their impact on engine out emissions. The results and the conclusions are supported by a statistical analysis of data that provides a quantitative significance of the effects of the two fuels on engine out emissions.

The relationship between engine oil formulations and catalyst performance was investigated by comparatively testing five engine oils. In addition to one baseline production oil with a calcium plus magnesium detergent system, the remaining four oils were specifically formulated with different additive combinations including: one worst case with no detergent and production level zinc dialkyldithiophosphate (ZDTP), one with calcium-only detergent and two best cases with zero phosphorus. Emissions performance, phosphorus loss from the engine oil, phosphorus-capture on the catalyst and engine wear were evaluated after accumulating 100,000 miles of taxi service in twenty vehicles. The intent of this comparative study was to identify relative trends.

An experiment was performed with a 1.3L catalytic converter design containing a front and rear catalyst each having a volume of 0.65 liters. This investigation varied the front catalyst parameters to study the effects of 1) substrate diameter, 2) substrate cell density, 3) Pd loading and 4) Rh loading on the FTP emissions on three different vehicles. Engine displacement varied from 2.4L to 4.7L. Eight different converters were built defined by a Taguchi L-8 array. Cold flow converter restriction results show the tradeoff in converter restriction between substrate cell density and substrate diameter. Vehicle FTP emissions show how the three vehicles are sensitive to the four parameters investigated. Platinum Group Metals (PGM) prices and Federal Test Procedure (FTP) emissions were used to define the emission value between the substrate properties of diameter and cell density to palladium (Pd) and rhodium (Rh) concentrations.

Embedded software is a software system that permanently resides in a device whose operations it controls. Typically, embedded systems are housed on flash memory or ROM chip and may be found in systems like cellular phones, household and office appliances having digital interfaces, medical equipment, automotive components, avionics etc. The fundamental problem facing the design of embedded systems is heterogeneity. Multiple styles of algorithms (e.g. signal processing, communications, and controls) are implemented using a variety of technologies (e.g., digital signal processors, microcontrollers, field-programmable gate arrays, application-specific integrated circuits, and real-time operating systems).Other challenges in automotive development are increasing requirements and therefore increasing size and complexity of the code, development and management of offshore / muti-site software development to reduce costs.

Embedded software is a software system that permanently resides in a device whose operations it controls. Typically, embedded systems are housed on flash memory or ROM chip and may be found in systems like cellular phones, household and office appliances having digital interfaces, medical equipment, automotive components, avionics etc. The fundamental problem facing the design of embedded systems is heterogeneity. Multiple styles of algorithms (e.g. signal processing, communications, and controls) are implemented using a variety of technologies (e.g., digital signal processors, microcontrollers, field-programmable gate arrays, application-specific integrated circuits, and real-time operating systems).Other challenges in automotive development are increasing requirements and therefore increasing size and complexity of the code, development and management of offshore / muti-site software development to reduce costs.

The auto industry has recently seen a trend in the packaging of metallic and thermoplastic components in “integrated” systems for cockpit modules. The following is a summary of engineering validation of an overmolded cross car beam (CCB) with HVAC system. The design concentrates on meeting the structural demands placed on a CCB constructed using a unique insert-molding process while meeting system demands of packaging and air handling.

A new family of automotive three-way conversion (TWC) catalyst technologies has been developed using a Precision Metal Addition (PMA) process. Precious metal (PGM) fixation onto the support occurs during the PMA step when the PGM is added to the slurry immediately prior to application to the monolith substrate. PMA slurries can be prepared with high precision and the slurry manufacturing process is greatly simplified. Further, it has been found that with the use of new generation washcoat (WC) materials, the same WC composition can be used for all three PGMs - Pt, Pd & Rh. Negative interactions between Pd and Rh in the same WC layer do not occur, providing advantages over older technologies. Thus, new WC compositions coupled with the PMA process offers precious metal flexibility. This FlexMetal family of catalyst technologies includes single layer Pd-only, Pd/Rh and Pt/Rh and dual layer bi-metal Pd/Rh and Pt/Rh and tri-metal Pt/Pd/Rh.

The 1997 F-Series and Expedition Instrument Panel programs were initially launched with steering column and glove compartment knee bolsters constructed of compression molded, glass filled polypropylene. First run capability of the material at production speeds was only 65 percent due primarily to dimensional stability (warp), paint adhesion, and excessive rework issues. A Ford APO (now Visteon) / Dow Automotive† team was formed to seek a replacement material / design for the glass filled polypropylene material which would solve the problems. The new material system had to meet or exceed current FMVSS 208 crash performance standards, provide improved quality and reduce variable and scrap costs all with a minimum tooling investment. Using Dow PULSE™ PC/ABS resin, the team designed / implemented a new knee bolster system in 12 months.

Goldilocks is a proposed serial communication protocol designed to find the “sweet spot” in trading off overhead, complexity, throughput, cost, and real time performance. Simple off line analysis of schedulability is a feature.. While backward compatible with CAN at the applications level, Goldilocks promises to be performance and feature competitive with FlexRay with less complexity and cost.

The success of stratified combustion is strongly determined by the injection and ignition system used. A large temporal and spatial variation of the main parameters - mixture composition and charge motion - in the vicinity of the spark location are driving the demands for significantly improved ignition systems. Besides the requirements for conventional homogeneous combustion systems higher ignition energy and breakdown voltage capability is needed. The spark location or spark plug gap itself has to be open and well accessible for the mixture to allow a successful flame kernel formation and growth into the stratified mixture regime, while being insensitive to potential interaction with liquid fuel droplets or even fuel film. For this purpose several different ignition concepts are currently being developed. The present article will give an ignition system overview for stratified combustion within Delphi Powertrain Systems.

The implementation and development efforts of lean NOx trap catalysts for heavy-duty applications decreased a number of years ago. Most heavy-duty engine manufacturers realized that the system complexity as well as the durability of such a system does not allow large volume production without significant risk. The current consensus of the heavy-duty community is that for 2010 the SCR system will be the prime path to meet the 0.2 g/bHPhr NOx emission standard, although this is subject to adequate infrastructure investment and progress. As a low volume manufacturer, in order to comply with the 2007 heavy-duty phase-in emission standards, General Engine Products (a subsidiary of AM General LLC) integrated a NOx adsorber system on the Optimizer 6500 engine. This engine features split combustion chamber design, rotary fuel injection pump and operates with EGR.

The need for entertainment and information has been a desire ever since people began driving cars. Over the last decade, the entertainment systems for vehicle applications have transformed from a basic audio system to an infotainment and information center similar to what is available in the home or office. The vehicle passenger compartment has already integrated the major innovations available in the home entertainment market, such as Video, Gaming, DVD, MP3, USB, Navigation and Internet connectivity. This rapid growth has been driven by both customer demand and increased affordability. This revolution has driven major changes in vehicle design to accommodate the new concepts and features. Vehicles are now an extension of our homes and offices in terms of convenience, information and entertainment, with content delivered in a safe and pleasant manner for the driver and passengers.