Search Results

A direct injection system in which fuel was injected through the cylinder wall was developed and detailed investigation was made for the purpose of reducing short-circuit of fuel in 2-stroke engines. As a result of dynamo tests using 430cc single cylinder engine, it was found that the injector was best attached at a location as close to TDC as possible on the rear transfer port side, and that the entire amount of fuel should be injected towards the piston top surface. Emissions were worsened if fuel was injected towards the exhaust port or spark plug. Although the higher injection pressure resulted in large emissions reduction effects, it did not have a significant effect on fuel consumption. When a butterfly exhaust valve, known to be effective against irregular combustion in the light load range, was applied, it was found to lead to further reductions in HC emission and fuel consumption while also improving combustion stability.

Reduction in the cycle-to-cycle variation (CCV) of combustion in internal combustion engines is required to reduce fuel consumption, exhaust emissions, and improve drivability. CCV increases at low load operations and lean/dilute burn conditions. Specifically, the factors that cause CCV of combustion are the cyclic variations of in-cylinder flow, in-cylinder distributions of fuel concentration, temperature and residual gas, and ignition energy. However, it is difficult to measure and analyze these factors in a production engine. This study used an optically accessible single-cylinder engine in which combustion and optical measurements were performed for 45 consecutive cycles. CCVs of the combustion and in-cylinder phenomena were investigated for the same cycle. Using this optically accessible engine, the volume inside the combustion chamber, including the pent-roof region can be observed through a quartz cylinder.

Cycle-to-cycle variation (CCV) of combustion in low load operation is a factor that may cause various problems in engine operation. Variable valve timing and variable ignition timing are commonly used as a means to reduce this variation. However, due to mountability and cost constraints, these methods are not feasible for use in motorcycle engines. Therefore, development of an engine with minimal CCV without utilizing complicated mechanisms or electronic control is required. CCV of combustion may be caused by fluctuations in in-cylinder flow, air-fuel mixture, temperature, residual gas and ignition energy. In this study, the relationship between CCV of combustion, in-cylinder flow fluctuation and air-fuel mixture fluctuation was the primary focus. In order to evaluate in-cylinder flow fluctuation, Time Resolved Particle Image Velocimetry (TR-PIV) technique was utilized.

Regarding S.I. gasoline engine, it is one of the most important matters to eliminate cyclic variation of combustion. Especially with high compression ratio and high boosted engine, the difficulties increase more. This paper describes the analysis of combustion process precisely by using many ion-current probes and CFD with the unique approaches. The number of used ion-current probes is 80 and they are mounted on whole combustion chamber wall especially including moving intake and exhaust valve faces. Thus cyclic variations of flame propagation can be measured precisely under high compression ratio and high boosted conditions in a multi-cylinder engine. In addition, CFD combustion simulation is conducted through full four strokes of continuous nine cycles. Moreover air motion and pressure vibration in intake and exhaust manifolds in whole cycles are considered. These unique approaches have made CFD result correspond to the measurement result of cyclic variations of actual combustion.

In order to obtain more reduction of two-stroke motorcycle engine noise than usual, it becomes necessary to make improvements within the combustion process itself. This study was carried out for two objectives. One is the investigation of the relationship between combustion and noise, and the other one is the development of noise reduction techniques. As the result, it was discovered that there was a significant correlation between engine noise and (dP/dθ)max, called the maximum rate of cylinder pressure rise. Therefore, the reduction of the (dP/dθ) max was recognized to be effective for engine noise reduction. The optimized alteration of combustion chamber shape is the most effective noise reduction technique, because it is able to reduce (dP/dθ) max without any sacrifice of engine power. In fact, the level of noise reduction can be predicted by one of the parameters obtained from the combustion chamber shape.

Recently the response of the engine speed at starting has more importance than ever for quick start satisfying rider’s needs, as well as exhaust emissions. We have developed a simulation for studying engine and starter specifications, engine control algorithm and other engine control parameters. This system can be utilized to realize appropriate starting time by considering air-fuel ratio under various conditions. This paper addresses what are taken account of in our method. Examples applying this to a conventional motorcycle engine are shown.

An original multi-body dynamics simulation program for reciprocating engine system with elastically deformable piston skirt was developed in order to understand and examine the secondary motion of piston. This program uses specialized equations of motion using only the rotational degree of freedom of each components taking the valiation of rotating speed of crank into account. In order to validate the practical use of this program, the calculations were compared with the measurements on the piston motion of a two-stroke engine for motorcycles and a four-stroke engine for automobiles, and good agreements were obtained between them.

Any improvements of the fuel economy with engines are always required for all petroleum fuel vehicles. The goal of such improvements must lead to reduce fuel consumption of the engines. However it may cause some deterioration with riding feeling that is one of the most important characteristics of the motorcycles. Yamaha has developed the strong hybrid motorcycle "HV-X"(hereafter the motorcycle). The motorcycle consists of a 4-stroke 250 cm₃ a cylinder engine and two 300V AC motors with a planetary gear set. The motorcycle reduces fuel consumption without severe influence onto the drive performance by utilizing the electric power.

In this study, lean combustion concept was investigated to realize better Fuel Economy (FE) on a single cylinder motorcycle engine. A low-pressure direct injection (DI) system was applied to realize lean stratified combustion concept with good combustion stability. In addition, Exhaust Gas Recirculation (EGR) system applicable to small motorcycle engines was used to attain FE improvement and NOx reduction. EGR gas temperature and EGR return position were focused on and effects on FE and NOx were investigated. Computational Fluid Dynamics (CFD) was used to reveal EGR distribution and air motion in both the intake port and the cylinder. As a result, the influence of the stratified charge, EGR temperature and EGR return position on FE and NOx were explained quantitatively. These techniques were effective in reducing NOx and improving FE for a single cylinder motorcycle engine.

The in-cylinder flow, mixture distribution, combustion and exhaust emissions in a research, five-valve purpose-built gasoline engine are discussed on the basis of measurements obtained using laser Doppler velocimetry (LDV), fast spark-plug hydrocarbon sampling, flame imaging and NOx/HC emissions using fast chemiluminescent and flame ionisation detectors/analysers. These measurements have been complemented by steady flow testing of various cylinder head configurations, involving single- and three-valve operation, in terms of flow capacity and in-cylinder tumble strength.

The improvement of fuel consumption is the most important issue for engine manufactures from the viewpoint of energy and environment conservation. A piston-cylinder system plays an important role for the reduction of an engine friction. For the improvement of the frictional behavior of the piston-cylinder system, it is beneficial to observe and analyze the frictional waveforms during an engine operation. To meet the above-mentioned demand, frictional waveforms were measured with using the renewed floating liner device. In the newly developed floating liner device, an actual cylinder block itself was used as a test specimen. The measured single cylinder was an aluminum monolithic type made of hypereutectic Al-17%Si alloy using a high pressure die casting process. The combined piston was a light weight forged piston and a DLC coated piston ring was used. For the measurement, 110cc air cooled single cylinder engine was used.

In this study, an improvement of fuel consumption by changing the exhaust timing of a two-stroke engine has been made. The study results revealed that a remarkable improvement of fuel economy is possible by controlling the exhaust timing according to the engine speed. The reason for the better fuel economy was clarified through an analysis of exhaust gases, theoretical cycle calculations, and an analysis of combustion pressure. As an example of actual application, the results of tests made on an engine equipped with Yamaha power Valve System (YPVS), which is a variable exhaust timing mechanism using a tabor-shaped valve, will also be discussed.

This paper proposes a novel engine starter system composed of a small-power electric motor and a simple mechanical valve train. The system makes it possible to design more efficient starters than conventional systems, and it is especially effective to restart engines equipped with idling stop systems. Recently, several idling stop systems, having intelligent start-up functions and highly-efficient generate capabilities have been proposed for motorcycles. One of challenges of the idling stop systems is the downsizing of electric motors for starting-up. However, there are many limitations to downsize the electric motors in the conventional idling stop systems, since the systems utilize the forward-rotational torque of the electric motors to compress the air-fuel mixture gas in the cylinders. Our studies exceeded the limitations of downsizing the electric motors by mainly using the engine combustion energy instead of the electric energy to go over the first compression top dead center.

A construction of the technology concerning fuel consumption improvement is an important problem not only for the four-wheeled vehicle but also for the motorcycle in recent years when petroleum resources are depleted rapidly. Yamaha originally developed a new fuel injection system (YMJET-FI) and applied the system to a single cylinder, water-cooled and small-displacement engine. In this paper, we would introduce the results of improving the fuel economy with keeping high performance. Improvements were noted in three matters, namely, in the lower load range, 1.Strengthening of in-cylinder flow, 2.Atomization of fuel spray, and 3.Reduction of wall film quantity.

This paper reports visualization of behavior of spray, wall film, and initial flame propagation in an SI engine with port fuel injection system for motorcycle in order to directly investigate their influences on combustion and relations among them. Borescopes were used to visualize the flame propagation in the combustion chamber and wall film in the intake port. Various injection systems and injection parameters were tested: injection direction, timing, and size of droplets to investigate the effect of mixture formation. It is concluded that combustion stability under low load condition is greatly influenced by mixture inhomogeneity in the combustion chamber whose evidence is the luminous emission. It is caused by direct induction of considerable amount of liquid fuel with large size of droplets into combustion chamber or too inhomogeneous mixture in the intake port.

With emergence of fuel cells which have much better thermal efficiency than internal combustion engines (later abbreviated as ICE), ICE has to improve its thermal efficiency to the level of 50%. One of the ways to improve the thermal efficiency of ICE is to utilize ultra-lean combustion and several technical papers have been published. But it seems the thermal efficiency has not been improved as the theory predicts. The test data of these technical papers were re-examined and it was concluded that the thermal dissociation of burned gas and NOx formation is the key factor of a discrepancy between the theory and the actual test data. In order to prevent an occurrence of thermal dissociation, emulsified fuels (mixture of carbonaceous fuels with water) was proposed.

A laser Doppler velocimeter is used to measure in real time the velocities of pipe flows in a crankcase-scavenged small two-cycle engine with piston and reed valves. Consequently the optical windows in each pipe must be exchanged instantly by using rotary window systems. The flows in both the inlet and exhaust pipes show different patterns in the motored and firing conditions, but the flows in the scavenging pipe are in a similar pattern regardless of the operating conditions.

In the past, the performance of motorcycle engines has improved quite rapidly through intensive competition in racing and in the marketplace. Motorcycle engines have contributed to the technological progress of internal combustion engines (hereafter abbreviated as ICE). Today's environmental concerns require motorcycle engines to improve fuel economy and exhaust emission pollutants. After examination of potential measures to improve the thermal efficiency of small engines, it was concluded that if engineers of motorcycle engines fail to take on new ideas such as those being developed in cold fusion, it is foreseen that motorcycle engines will be replaced with new power plants as was seen on locomotives in the past.

THE MULTI-VALVE FOUR STROKE CYCLE engine design trend is Coward increased engine power and higher fuel efficiency. While a four-valve system is the most common direction, problems occur when the valve area is widened by increasing the cylinder bore for a higher engine output. The layout of four larger valves causes the combustion chamber shape to flatten and the combustion time period to increase. In pursuit of the optimum multi-valve engine we have studied four, five, six and seven-valve per cylinder design. Performance targets and design constraints led us toward the successful five-valve engine technology. This technology develops high engine torque and efficient combustion over a wide range of engine speeds.

The purpose of this paper is to investigate the effect of the piston shape and weight on the friction losses. The motoring test was conducted on pistons with various shapes, rigidities, and weights at 3000-16000 rpm. The test results suggested that the piston friction loss would be abruptly increased mainly because of the increase in the skirt friction caused by the change of the piston attitude. Then, the piston behavioral simulation was conducted using a two-dimensional rigid model in consideration of the skirt rigidity, which proved the above suggestion. This paper consists of the paper presented at 1990 JSAE Autumn Convention and the results of the investigation we conducted based on the calculation of piston behavioral simulation.