Search Results

Rape oil, as used in fresh cooking oil (FCO), and the methyl ester derived from waste cooking oil (WCOB100) were tested as 100% biofuels (B100) on a heavy duty DI diesel engine under steady state conditions. The exhaust emissions were measured and compared to those for conventional low sulphur (<50ppm) diesel fuel. The engine used was a 6 cylinder, turbocharged, intercooled Perkins Euro2 Phaser Engine, fitted with an oxidation catalyst. The engine out gaseous emissions results for WCOB100 showed a large decrease in CO and HC emissions, but a small increase in NOx emissions compared to diesel. However, for FCO the CO and HC increased relative to WCOB100 and CO was higher than for diesel, indicating deterioration in fuel/air mixing. The particulate matter (PM) emissions for WCOB100 were similar to those for diesel at the 23kw condition, but greatly reduced at 47kw. The FCO produced higher engine out PM at both power conditions due to a higher volatile organic fraction (VOF).

A Euro 3 1.8-liter diesel vehicle with an oxidation catalyst was used to investigate real-world exhaust emissions over a real-world driving cycle that included urban congested traffic and extra-urban driving conditions. Diesel fuel and B100 were compared. The B100 fuel was Fatty Acid Methyl Ester (FAME), derived from waste cooking oil, which was mainly RME. A multifunctional additive package was added at 800 ppm to control fuel injector deposit formation. Gaseous emissions were monitored using an on-board heated Temet FTIR exhaust emission analyzer, which can measure 52 species at a rate of 0.5 Hz. A Horiba on board emissions measuring system was also used (OBS 1300), which measures the exhaust mass flow rate together with air/fuel ratio.

This work investigates the effect of a multifunctional diesel fuel additive package used with RapeSeed Oil (RSO) as a fuel in a DI heavy duty diesel engine. The effects on fuel injectors’ cleanliness were assessed. The aim was to maintain combustion performance and preventing the deterioration of exhaust emissions associated with injector deposit build up. Two scenarios were investigated: the effect of deposit clean-up by a high dose of the additive package; and the effect of deposit prevention using a moderate dose of the additive package. Engine combustion performance and emissions were compared for each case against use of RSO without any additive. The engine used was a 6 cylinder, turbocharged, intercooled Perkins Phaser Engine, fitted with an oxidation catalyst and meeting the Euro II emissions limits. The tests were conducted under steady state conditions of 23kW and 47kW power output at an engine speed of 1500 rpm.

Results of an experimental study of a DI Diesel engine are presented, which show the influence of partial premixing fumigation of the intake air with diesel fuel on the exhaust emissions and the engine performance parameters. Exhaust emissions of NOx, CO, UHC, TPM, SOF and Carbon were measured and quantified. Engine performance parameters include the event of the start of combustion and fuel consumption besides other parameters, which were published elsewhere. The study also showed that during a “normal operation” of a DI diesel engine, no emissions trade-off exists between NOx and TPM. Rather these emissions need separate technological measures for their specific control. Two methods of diesel fumigation were used. The difference between these two methods was the degree of premixing of diesel fuel with the intake air.

An oxidation catalyst was fitted on a DI diesel engine for an experimental study involving an oxidation catalyst and the use of superheated steam for fumigating the intake air. Results are compared with that of the influence of low level of fumigation of the intake air with superheated diesel fuel. Exhaust emissions of NOx, CO, UHC, TPM, SOF and Carbon were measured and quantified on upstream and downstream of a low light off temperature (250 °C) oxidation catalyst. The technique used an electric vaporizer for producing superheated steam and prevaporised superheated diesel fumes at 350 °C, respectively. A low emissions version of Perkins 4-236 engine with squish lip piston was run both with and without fumigation at two speeds 1200 rpm and 2200 rpm. Roughly covering both city and highway running conditions.

Results showed the influence of the oxidation catalyst on exhaust emissions from a DI diesel engine due to the partial premixing, fumigation of the intake air with diesel fuel. Exhaust emissions of NOx, CO, UHC, TPM, SOF and Carbon were measured and quantified on upstream and downstream of a low light off temperature (250 °C) oxidation catalyst. Two methods of diesel fumigation of the intake air with fuel were used. The difference between these two methods was the degree of premixing of diesel fuel with the intake air. The first technique used a high-pressure fine diesel spray onto a glow plug and the second technique used an electric vaporizer for prevaporised superheated diesel fumes at 350 °C. A low emissions version of Perkins 4-236 engine with squish lip piston was run both with and without fumigation at two speeds 1200 rpm and 2200 rpm. Roughly covering both city and highway running conditions.

Aldehydes and other Volatile Organic compounds (VOC) are assessed under cold start and steady state conditions using a Perkins Phaser 6 litre diesel engine. A comparison is made between petroleum diesel fuel (PD), 100% biodiesel (WME) and 100% rapeseed oil (RSO). A Temet FTIR was used to determine aldehydes including formaldehyde, acetaldehyde and acrolein. The diesel engine was cold started at room temperature using a step start up procedure that kept the power output constant at two steady state conditions: 23kW and 47kW. Very little difference was observed between petroleum diesel and biodiesel aldehyde emissions at either steady state conditions or during cold start. There was, however, an increase in aldehydes at steady state for rapeseed oil, particularly at low load, but only for from ∼10ppm to 25 ppm for formaldehyde (i.e. 0.12g/kWh to 0.37g/kWh). During cold start conditions, the emissions were significantly higher for rapeseed oil than for petroleum diesel.

Hydrogenated Vegetable Oil (HVO) diesel fuels have the potential to provide a reduced carbon footprint for diesel engines and reduce exhaust emissions. Therefore, it is a strong candidate for transport and diesel powered machines including electricity generators and other off-road machines. In this research, a waste cooking oil derived HVO diesel was investigated for its combustion and emission performance including ignition delays, size segregated particulate number emissions and gaseous emissions. The results were compared to the standard petroleum diesel. A EURO5 emission compliant three litre, direct injection, intercooled IVECO diesel engine equipped with EGR was used which has a maximum power output of 96kW. The engine was equipped with an integrated DOC and DPF aftertreatment system. Both the upstream and downstream of the aftertreatment emissions were measured. The tests were conducted at different RPM and loads at steady state conditions.

A Gas to liquid (GTL) fuel was investigated for its combustion and emission performance in an IVECO EURO5 DI diesel engine with a DOC (Diesel Oxidation Catalyst) and DPF (Diesel Particle Filter) installed. The composition of the GTL fuel was analyzed by GC-MS (gas chromatography-mass spectrometry) and showed the carbon distribution of 8-20. Selected physical properties such as density and distillation were measured. The GTL fuel was blended with standard fossil diesel fuel by ratios of diesel/GTL: 100/0, 70/30, 50/50, 30/70 and 0/100. The engine was equipped with a pressure transducer and crank angle encoder in one of its cylinders. The properties of ignition delay and maximum in-cylinder pressure were studied as a function of fraction of the GTL fuel. Particle emissions were measured using DMS500 particle size instrument at both upstream (engine out) and downstream of the DPF (DPF out) for particle number concentrations and size distribution from 5 nm to 1000 nm.

The transport sector is one of the major contributors to greenhouse gas emissions. This study investigated three greenhouse gases emitted from road transport using a probe vehicle: CO₂, N₂O and CH₄ emissions as a function temperature. It should be highlighted that methane is a greenhouse gas that similarly to carbon dioxide contributes to global warming and climate change. An oxidation catalyst was used to investigate CO₂, N₂O and CH₄ GHG emissions over a real-world driving cycle that included urban congested traffic and extra-urban driving conditions. The results were determined under hot start conditions, but in congested traffic the catalyst cooled below its light-off temperature and this resulted in considerable N₂O emissions as the oxidation catalyst temperature was in the N₂O formation band. This showed higher N₂O during hot start than for diesel fuel and B100 were compared. The B100 fuel was Fatty Acid Methyl Ester (FAME), derived from waste cooking oil, which was mainly RME.

Reduction of NOx was achieved in an experimental study in a DI Diesel engine. Results are presented, which show the comparison of the influence of partial fumigation of the intake air with superheated diesel fuel vapour and that of steam on the exhaust emissions and the engine performance parameters. Exhaust emissions of NOx, CO, UHC, TPM, SOF and Carbon were measured and quantified. The technique used for fumigating the intake air with fuel and steam consisted of an electric vaporizer for producing perfectly prevaporised superheated diesel fumes and steam at 350°C. A low emissions version of Perkins 4-236 engine with squish lip piston was run with the fumigation of the intake air with superheated fuel vapour and that of steam at two speeds 1200 rpm and 2200 rpm, roughly covering both city and highway running conditions.

A rapeseed methyl ester biodiesel RMEB100 was tested on a heavy duty DI diesel engine under steady state conditions. The combustion performance and exhaust emissions were measured and compared to a standard petroleum derived diesel fuel. The engine used was a 6 cylinder, turbocharged, intercooled Perkins Phaser Engine, with emission compliance of EURO 2, fitted with an oxidation catalyst. The exhaust samples were taken both upstream and downstream of the catalyst. Particulates were collected and analysed for VOF, carbon and ash. A MEXA7100 gas analysis system was used for legislated gas analysis such as CO, CO2, NOx and total hydrocarbons. A FTIR analysis system was deployed for gaseous hydrocarbon speciation, which is capable of speciating up to 65 species. The results showed a significant reduction in total particulate mass, particulate VOF, CO, THC and aldehydes when using RMEB100.