Search Results

It is well established that reducing the compression ratio (CR) of a diesel engine leads to a significant increase in hydrocarbon (HC) and carbon monoxide (CO) emissions, especially in cold and transient conditions. Hence, it is essential to find new strategies to reduce the HC and CO emissions of a low compression ratio (LCR) diesel engine in transient conditions. In the present work, a detailed evaluation of different warm-up technologies was conducted for their effects on transient emissions characteristics of a single-cylinder naturally aspirated LCR diesel engine. For this purpose, the engine was coupled to an instrumented transient engine dynamometer setup. A transient cycle of 160 seconds with starting, idling, speed ramp-up and load ramp-up was defined, and the engine was run in automatic mode by the dynamometer. The experiments were conducted by overnight soaking the engine at a specified temperature of 25 deg.C.

In a direct-injection (DI) engine, charge motion and mixture preparation are among the most important factors deciding the performance and emissions. This work was focused on studying the effect of injector positioning on fuel-air mixture preparation and fuel impingement on in-cylinder surfaces during the homogeneous mode of operation in a naturally aspirated, small bore, 0.2 l, light-duty, air-cooled, four-stroke, spark-ignition engine modified to operate under the DI mode. A commercially available, six-hole, solenoid-operated injector was used. Two injector locations were identified based on the availability of the space on the cylinder head. One location yielded the spray-guided (SG) configuration, with one of the spray plumes targeted towards the spark plug. In the second location, the spray plumes were targeted towards the piston top in a wall-guided (WG) configuration so as to minimize the impingement of fuel on the liner.

The upcoming Bharat Stage VI (BS VI) emission legislation has put enormous pressure on the future of small diesel engines which are widely used in the Indian market. The present work investigates the emission reduction potential of a common rail direct injection single cylinder diesel engine by adopting a holistic approach of lowering the compression ratio, boosting the intake air and down-speeding the engine. Experimental investigations were conducted across the entire operating map of a mass-production, light-duty diesel engine to examine the benefits of the proposed approach and the results are quantified for the modified Indian drive cycle (MIDC). By reducing the compression ratio from 18:1 to 14:1, the oxides of nitrogen (NOx) and soot emissions are reduced by 40% and 75% respectively. However, a significant penalty in fuel economy, unburned hydrocarbon (HC) and carbon monoxide (CO) emissions are observed with the reduced compression ratio.

To comply with the stringent future emission mandates of light-duty diesel engines, it is essential to deploy a suitable combination of emission control devices like diesel oxidation catalyst (DOC), diesel particulate filter (DPF) and DeNOx converter (LNT or SCR). Arriving at optimum size and layout of these emission control devices for a particular engine through experiments is both time and cost-intensive. Thus, it becomes important to develop suitable well-tuned simulation models that can be helpful to optimize individual emission control devices as well as arrive at an optimal layout for achieving higher conversion efficiency at a minimal cost. Towards this objective, the present work intends to develop a one-dimensional Exhaust After Treatment Devices (EATD) model using a commercial code. The model parameters are fine-tuned based on experimental data. The EATD model is then validated with experiment data that are not used for tuning the model.

Supercharging a single-cylinder diesel engine has proved to be a viable methodology to reduce engine-out emissions and increase full-load torque and power. The increased air availability of the supercharger (SC) system helps to inject more fuel quantity that can improve the engine's full-load brake mean effective pressure (BMEP) without elevating soot emissions. However, the increased inlet temperature of the boosted air and the availability of excess oxygen can pose significant challenges to contain oxides of nitrogen (NOx) emissions. Hence, it is important to investigate the potential NOx reduction options in supercharged diesel engines. In the present work, the potential of low-pressure exhaust gas recirculation (LP EGR) was evaluated in a single-cylinder supercharged diesel engine for its benefits in NOx emission reduction and impact on other criteria emissions and brake specific fuel consumption (BSFC).

In this work methanol was port injected while diesel was injected using a common rail system in a single cylinder non-road CI engine. Experiments were conducted with single (SPI) and double (DPI - pilot and main) injection of the directly injected diesel at 75% load and at a constant speed of 1500 rpm. The effects of methanol to diesel energy share (MDES) and injection scheduling on combustion stability, efficiency and emissions were evaluated. Initially, in the SPI mode, the methanol to diesel Energy Share (MDES) was varied, while the injection timing of diesel was always fixed for best brake thermal efficiency (BTE). Increase in the MDES resulted in a reduction in NOx and smoke emissions because of the high latent heat of vaporization of methanol and the oxygen available. Enhanced premixed combustion led to a raise in brake thermal efficiency (BTE). Coefficient of variation of IMEP, peak pressure and BTE were deteriorated which limited the usable MDES to 43%.

In a dual fuel engine a primary fuel that is generally gaseous is mixed with air, compressed and ignited by a small pilot spray of diesel as in a diesel engine. Dual fuel engines suffer from the problems of poor brake thermal efficiency and high HC emissions, particularly at low outputs. In the present experimental work, the effects of intake charge temperature, pilot fuel quantity, exhaust gas recirculation and throttling of the intake on improving the performance of a LPG-diesel dual fuel engine have been studied. Results indicate that at low outputs an increase in the intake temperature and pilot quantity is advantageous. HC level generally reduces with increase in pilot quantity and intake temperature. Exhaust gas recirculation (EGR) coupled with intake heating raises the brake thermal efficiency and lowers HC emissions. With throttling and EGR there is a significant reduction in the HC levels and an improvement in brake thermal efficiency at low loads.

A single cylinder, direct injection diesel engine was run on water diesel emulsion at a constant speed of 1500 rpm under variable load conditions. Water to diesel ratio of 0.4 on the mass basis was used. Tests indicated a considerable reduction in smoke and NO levels. This was accompanied by an increase in brake thermal efficiency at high outputs. HC & CO levels, ignition delay and rate of pressure rise went up. The heat release rate in the premixed burn period was higher. When the oxygen concentration in the intake air was enhanced in steps up to 25% along with the use of water diesel emulsion, the brake thermal efficiency was improved and there was a further reduction in the smoke level. HC and CO levels also dropped. NO emission went up due to increased temperature and oxygen availability. An oxygen concentration of 24% by volume was optimal as the NO levels were near about base diesel values.

Use of vegetable oils in diesel engines results in increased smoke and reduced brake thermal efficiency. Dual fuel engines can use a wide range of fuels and yet operate with low smoke emissions and high thermal efficiency. In this work, a single cylinder diesel engine was converted to use vegetable oil (Jatropha oil) as the pilot fuel and methanol as the inducted primary fuel. Tests were conducted at 1500 rev/min and full load. Different quantities of methanol and Jatropha oil were used. Results of experiments with diesel as the pilot fuel and methanol as the primary fuel were used for comparison. Brake thermal efficiency increased in the dual fuel mode when both Jatropha oil and diesel were used as pilot fuels. The maximum brake thermal efficiency was 30.6% with Jatropha oil and 32.8% with diesel. Smoke was drastically reduced from 4.4 BSU with pure Jatropha oil operation to 1.6 BSU in the dual fuel mode.

In many Asian countries a significant automobile market share is held by two and three wheelers. Generally, cost and simplicity considerations limit the performance and emission levels of small engines. Methanol is an excellent alternative fuel for SI engines due to its high-octane number, high flame speed, presence of oxygen in its molecule and thus can be used to enhance the performance of small engines. However, use of neat methanol in SI engines poses constraints due to low energy density and poor vaporization characteristics. Also, the effectiveness of methanol as a fuel has still to be thoroughly investigated in small-bore SI engines in order to assess its potential. In this work, a small-bore 200cc three-wheeler automotive engine was modified to operate in the port fuel injection mode with neat methanol as the fuel.

The property of methanol to surface ignite can be exploited to use it in a diesel engine even though its cetane number is very low. Poor lubricity of methanol is still an issue and special additives are needed in order to safeguard the injection system components. In this work a common rail three cylinder, turbocharged diesel engine was run in the glow plug based hot surface ignition mode under different injection strategies with methanol as the main fuel in a blend with n-butanol. n-Butanol was used mainly to enhance the viscosity and lubricity of the blend. The focus was on the effect of different injection strategies. Initially three blends with methanol to n-butanol mass ratios of 60:40, 70:30 and 80:20 were evaluated experimentally with single pulse fuel injection. Subsequently the selected blend of 70:30 was injected as two pulses (with almost equal mass shares) with the gap between them and their timing being varied.

The present work investigates the effects of lowering the compression ratio (LCR) from 18:1 to 14:1 and optimizing the fuel injection parameters across the operating range of a mass production light-duty diesel engine. The results were quantified for a regulatory Indian drive cycle using a one-dimensional simulation tool. The results show that the LCR approach can simultaneously reduce the oxides of nitrogen (NOx) and soot emissions by 28% and 64%, respectively. However, the unburned hydrocarbon (HC) and carbon monoxide (CO) emissions increased significantly by 305% and 119%, respectively, with a 4.5% penalty in brake specific fuel consumption (BSFC). Hence, optimization of fuel injection parameters specific to LCR operation was attempted. It was evident that advancing the main injection timing and reducing the injection pressure at low-load operating points can significantly help to reduce BSFC, HC and CO emissions with a slight increase in the NOx emissions.

Direct injection of fuel has been seen as a potential method to reduce fuel short circuiting in two stroke engines. However, most work has been on low pressure injection. In this work, which employed high pressure direct injection in a small two stroke engine (2S-GDI), a detailed study of injection parameters affecting performance and combustion has been presented based on experiments for evaluating its potential. Influences of injection pressure (IP), injection timing (end of injection - EOI) and location of the spark plug at different operating conditions in a 199.3 cm3 automotive two stroke engine using a real time open engine controller were studied. Experiments were conducted at different throttle positions and equivalence ratios at a speed of 3000 rpm with various sets of injection parameters and spark plug locations. The same engine was also run in the manifold injection (2S-MI) mode under similar conditions for comparison.

Owing to a high power-to-weight ratio, mini internal combustion engine is used in propelling an unmanned air vehicle. In comparison to the performance characteristics, the investigations on the combustion aspects of mini engines are scanty. This investigation concerns study of the combustion process of a mini engine and its variability. For this purpose, the experimental cylinder pressure histories were obtained on a laboratory set-up of a 7.45 cm3 capacity mini engine. The analyses of experimental data at different throttle settings reveal that there existed a varied range of rich and lean misfiring limits around a reference equivalence ratio that corresponds to the respective maximum indicated mean effective pressure. At the limiting equivalence ratios, cylinder pressure measurements showed a high degree of cycle-to-cycle variations. In some cases, a slow combustion or misfiring event preceded a rapid combustion.

Despite the advantages of turbocharging in improved engine performance and reduced exhaust emissions, commercial single-cylinder engines used for automotive applications remain naturally aspirated (NA) and are not generally turbocharged. This is due to the shortcomings with pulsated and intermittent exhaust gas flow into the turbine and the phase lag between the intake and exhaust stroke. In the present study, experimental investigations are initially carried out with a suitable turbocharger closely coupled to a single-cylinder diesel engine. Results indicated that the engine power dropped significantly by 40% for the turbocharged engine compared to the NA version even though the air mass flow rate was increased by at least 1.5 times with turbocharging. A novel approach of decoupling the turbine and the compressor and coupling them separately to the engine is proposed to address these limitations.

Single-cylinder engines in mass production are generally not turbocharged due to the pulsated and intermittent exhaust gas flow into the turbocharger and the phase lag between the intake and exhaust stroke. The present work proposes a novel approach of decoupling the turbine and the compressor and coupling them separately to the engine to address these limitations. An impulse turbine is chosen for this application to extract energy during the pulsated exhaust flow. Commercially available AVL BOOST software was used to estimate the overall engine performance improvement of the proposed novel approach compared to the base naturally aspirated (NA) engine. Two different impulse turbine layouts were analyzed, one without an exhaust plenum and the second layout having an exhaust plenum before the power turbine. The merits and limitations of both layouts are compared in the present study.

Hybrid drive trains have to be cost effective for implementation in small two-wheelers especially scooters which constitute the majority of the market in several Asian countries. Integrating an electric motor with the conventional IC Engine drivetrain while retaining the CVT (Continuously Variable Transmission) is a cost-effective proposition. Such a development will need accounting for the behaviour of the engine, electrical drive and the belt driven CVT. A map-based engine model and a physics-based CVT model were developed in Simulink and validated with experimental data on the WMTC drive-cycle. A steady state map-based emission model and a motor model were also used. Simulations were performed on two parallel hybrid layouts namely P2 wherein the electric motor was placed before the CVT and P3 where the motor was placed in the final drive after the CVT while retaining the base 110 cc scooter powertrain.

This study deals with the development of an internal EGR (Exhaust Gas Recirculation) system for NOx reduction on a six cylinder, turbocharged intercooled, off-road diesel engine based on a modified cam with secondary lift. One dimensional thermodynamic simulation model was developed using a commercially available code. MCC heat release model was refined in the present work by considering wall impingement of the fuel as given by Lakshminarayanan et al. The NOx prediction accuracy was improved to a level of 90% by a generic polynomial fit between air excess ratio and prediction constants. Simulation results of base model were correlating to more than 95% with experimental results for ISO 8178 C1 test cycle. Parametric study of intake and exhaust valve events was conducted with 2IVO (Secondary Intake Valve Opening) and 2EVO (Secondary Exhaust Valve Opening) methods. Combinations of different opening angles and lifts were chosen in both 2IVO and 2EVO methods for the study.

In order to comply with the stringent future emission mandates of automotive diesel engines it is essential to deploy a suitable combination of after treatment devices like diesel oxidation catalyst (DOC), diesel particulate filter (DPF) and DeNox converter (Lean NOx Trap (LNT) or Selective Catalytic reduction (SCR) system). Since arriving at a suitable strategy through experiments will involve deploying a lot of resources, development of well-tuned simulation models that can reduce time and cost is important. In the first phase of this study experiments were conducted on a single cylinder light duty diesel engine fitted with a diesel oxidation catalyst (DOC) at thirteen steady state mode points identified in the NEDC (New European Driving cycle) cycle. Inlet and exit pressures and temperatures, exhaust emission concentrations and catalyst bed temperature were measured. A one dimensional simulation model was developed in the commercial software AVL BOOST.

In this work, a 7.45 cc capacity glow plug based two-stroke engine for mini aircraft applications was evaluated for its performance, emissions and combustion. It uses a fuel containing 65% methanol, 25% castor oil and 10% nitromethane by volume. Since test rigs are not readily available for such small engines, a reaction type test bed with low friction linear and rolling element bearings was developed and used successfully. The propeller of the engine acted as the load and also the flywheel. Pressure time diagrams were recorded using a small piezoelectric pressure transducer. Tests were conducted at two different throttle positions and at various equivalence ratios. The brake thermal efficiency was generally in the range of 4 to 17.5% depending on the equivalence ratio and throttle position. IMEP was between 2 and 4 bar. It was found that only a part of the castor oil that was supplied participated in the combustion process.