Search Results

Particulate number (PN) standards in the current ‘Euro 6’ European emissions standards pose a challenge for engine designers and calibrators during the warm-up phases of cold direct injection spark ignition (DISI) engines. To achieve catalyst light-off in the shortest time, engine strategies are often employed which inherently use more fuel to attain higher exhaust temperatures. This can lead to the generation of locally fuel-rich regions within the combustion chamber and the emission of particulates. This investigation analyses the combustion structures during the transient start-up phase of an optical DISI engine. High-speed, colour 9 kHz imaging was used to investigate five important operating points of an engine start-up strategy whilst simultaneously recording in-cylinder pressure.

Particulate Matter (PM) emissions reduction is an imminent challenge for Direct Injection Spark Ignition (DISI) engine designers due to the introduction of Particulate Number (PN) standards in the proposed Euro 6 emissions legislation aimed at delivering the next phase of air quality improvements. An understanding of how the formation of combustion-derived nanoparticulates in engines is affected by the engine operating temperature is important for air quality improvement and will influence future engine design and control strategies. This investigation has examined the effect on combustion and PM formation when reducing the engine operating temperature to -7°C. A DISI single-cylinder optical research engine was modified to simulate a range of operating temperatures down to the proposed -7°C.

Time resolved digital particle image velocimetry (TRDPIV) data is presented for the in-cylinder flow field of a motored four stroke multi-valve direct injection spark ignition (DISI) optical internal combustion (IC) engine. It is widely accepted that IC engine performance, in terms of both engine emissions and efficiency, is fundamentally affected by the in-cylinder air motion. Therefore improved knowledge of the fundamental fluid flow processes present during the intake and compression phase of the engine cycle is required. More specifically, increased understanding of the flow field cyclic variation will facilitate accurate control of the mixing and ignition development. This paper highlights the application of a new TRDPIV system to provide both spatial and temporal in-cylinder flow field development over multiple engine cycles for improved understanding of cyclic variation.

This research introduces a new, novel approach to reverse flow particulate filter regeneration enabled by rapidly pulsed electric discharges. The discharges physically dislodge particulate matter (PM) from the filter substrate and allow a very low reverse air flow to transport it to a soot handling system. The system is operable independent of filter temperature, does not expose the filter to high thermal stresses or temperatures, has no apparent upper limit for filter PM-mass level (regeneration of a filter up to 17 g/L has been demonstrated), and does not require any catalyst. The system is inherently scalable allowing application to monolithic filters of any size or shape and can be tailored to suit specific application requirements such as limits on maximum regeneration time or power consumption. For example a light duty application would require as little as 200-500W electrical power to regenerate a filter in less than ten minutes (i.e. passenger car GPF or DPF).

Time resolved intake runner flow field data is presented for a motored single cylinder four stroke, direct injection spark ignition (DISI) optical internal combustion (IC) engine with an optically accessible intake runner. Previous studies have shown the fundamental influence in-cylinder air motion has on engine performance, exhibiting a controlling factor on the mixing process and early flame kernel development. An improved understanding of the in-cylinder flow fields during the intake and compression process leading up to ignition is required. However, knowledge of the intake runner flow field during the intake phase of the engine cycle is required to establish the effect of intake runner flow variation on in-cylinder flow field development. This paper presents the use of a new time resolved digital particle image velocimetry system within the intake runner to study runner flows and their variation over many engine cycles.

Diesel engine emissions of NOX and particulate matter (PM) can be reduced simultaneously through the use of high levels of exhaust gas recirculation (EGR) to achieve low temperature combustion (LTC). These reductions are highly dependent on the oxygen concentration in the combustion chamber. This paper investigates varying the intake pressure to adjust the oxygen concentration and the corresponding impacts on emissions for EGR rates up to 65%. An engine operating condition corresponding to 600 kPa gross-indicated mean effective pressure (gimep) at 2500 rpm is investigated using a 0.51-liter single-cylinder high-speed direct-injection (HSDI) diesel engine. This facility is equipped with independent control of the intake pressure and temperature, the EGR rate and the exhaust back pressure.

Low temperature combustion (LTC) in diesel engines offers attractive benefits through simultaneous reduction of nitrogen oxides and soot. However, it is known that the in-cylinder conditions typical of LTC operation tend to produce high emissions of unburned hydrocarbons (UHC) and carbon monoxide (CO), reducing combustion efficiency. The present study develops from the hypothesis that this characteristic poor combustion efficiency is due to in-cylinder mixture preparation strategies that are non-optimally matched to the requirements of the LTC combustion mode. In this work, the effects of three key fuel path parameters - injection fuel quantity ratio, dwell and injection timing - on CO and HC emissions were examined using a Central Composite Design (CCD) Design of Experiments (DOE) method.

Low temperature combustion (LTC) of diesel fuel offers a path to low engine emissions of nitrogen oxides (NOx) and particulate matter (PM), especially at low loads. Borescopic optical imaging offers insight into key aspects of the combustion process without significantly disrupting the engine geometry. To assess LTC combustion, two-colour pyrometry can be used to quantify local temperatures and soot concentrations (KL factor). High sensitivity photo-multiplier tubes (PMTs) can resolve natural luminosity down to low temperatures with adequate signal-to-noise ratios. In this work the authors present the calibration and implementation of a borescope-based system for evaluating low luminosity LTC using spatially resolved visible flame imaging and high-sensitivity PMT data to quantify the luminous-area average temperature and soot concentration for temperatures from 1350-2600 K.