Search Results

ELEVATE (European Low Emission V4 Automotive Two-stroke Engine) was a research project part funded by the European Commission to design and develop a compact and efficient gasoline two-stroke automotive engine. Five partners were involved in the project, IFP (Institut Français Du Pétrole) who were the project leaders, Lotus, Opcon (Autorotor and SEM), Politecnico di Milano and Queen's University Belfast. The general project targets were to achieve Euro 3 emissions compliance without DeNOx catalisation, and a power output of 120 kW at 5000 rev/min with maximum torque of 250 Nm at 2000 rev/min. Specific targets were a 15% reduction in fuel consumption compared to its four-stroke counterpart and a size and weight advantage over the four-stroke diesel with significant reduction in particulate and NOx emissions. This paper describes the design philosophy of the engine as well as the application of the various partner technologies used.

The relative contribution of two wheelers to local atmosphere pollution is increasing more and more due to ultra low emissions regulation applied to other vehicle as cars. In 1999, the first European emissions regulations for 50cc mopeds and scooters appeared (Euro I) and will also become more and more severe by the time. Euro II (2002) level will correspond to the next step. IFP has developed a simplified Direct Injection technology, named SCIP™, derived from the well known IAPAC® technology without the need of additional camshaft. This technology has been integrated with the MC500 Engine Management System developed by SAGEM for the growing 2-wheelers application. The final simple and cheap product is therefore well adapted to small displacement 2-stroke engines as 50cc engine for 2-wheelers application. This paper presents the development of a 50 cc scooter engine using SCIP™ technology and the calibration of the MC500 System to achieve Euro II regulation.

The paper deals with experimental activity concerning ATAC, which, in two-stroke gasoline engines, helps solving the crucial problem of combustion instability at light loads. ATAC consists of employing the energy of residual gas to prime an efficient combustion. The research is aimed to give further insight into ATAC mechanism both by visualisation of the combustion process and by examination of the influence which relevant parameters like air-fuel ratio, engine speed, compression ratio, scavenging passage design have on ATAC operation. Several results have been acquired and collected hitherto. A part of them are shown and discussed in this paper.

The IAPAC Direct fuel Injection (DI) system, developed by IFP, has already well proven its capability to reduce pollutants emissions and fuel consumption of 2-stroke engines. This crankcase Compressed Air Assisted Fuel Injection Process allowing the introduction of the fuel separately from the scavenging air, minimizes the fuel short-circuiting. In earlier works, results of the implementation of the IAPAC system on cylinder displacement from 125 cc to 400 cc have been presented in various papers. These first prototypes were all using a camshaft to drive the IAPAC DI poppet valve, which was considered as a limitation for applying this system to small displacement 2-stroke engines. The new SCIP™ system is no more using a camshaft neither driveshaft, or any electric power supply to drive the DI air assisted injection valve.

The IAPAC Direct fuel Injection (DI) system, developed by IFP, has already well proven its capability to reduce pollutants emissions and fuel consumption of 2-stroke engines. This crankcase Compressed Air Assisted Fuel Injection Process allowing the introduction of the fuel separately from the scavenging air, minimizes the fuel short-circuiting. In earlier works, results of the implementation of the IAPAC system on cylinder displacement from 125 cc to 400 cc have been presented in various papers. These first prototypes were all using a camshaft to drive the IAPAC DI poppet valve, which was considered as a limitation for applying this system to small displacement 2-stroke engines. The new SCIP™ system is no more using a camshaft neither driveshaft, or any electric power supply to drive the DI air assisted injection valve.

The purpose of the ELEVATE (European Low Emission V4 Automotive Two-stroke Engine) industrial research project is to develop a small, compact, light weight, high torque and highly efficient clean gasoline 2-stroke engine of 120 kW which could industrially replace the relatively big existing automotive spark ignition or diesel 4-stroke engine used in the top of the mid size or in the large size vehicles, including the minivan vehicles used for multi people and family transportation. This new gasoline direct injection engine concept is based on the combined implementation on a 4-stroke bottom end of several 2-stroke engine innovative technologies such as the IAPAC compressed air assisted direct fuel injection, the CAI (Controlled Auto-Ignition) combustion process, the D2SC (Dual Delivery Screw SuperCharger) for both low pressure engine scavenging and higher pressure IAPAC air assisted DI and the ETV (Exhaust charge Trapping Valve).