Search Results

The in-cylinder direct injection of fuels can be a further step towards cleaner and more efficient internal combustion engines. However, the injector design and its characterization, both experimental and from numerical simulation require accurate diagnostics and efficient models. This work aims to simulate the complex behavior of the gaseous and liquid jets through an outwardly opening injector characterized by optical diagnostics using a one-dimensional model without using three dimensional models. The behavior of the jet from an outwardly opening injector changes according to the type of fuel. In the case of the gas, the experimental investigations put in evidence three main jet regions: 1) near-field region where the jet shows a complex gas-dynamic structure; 2) transition region characterized by intense mixing; 3) far-field region characterized by a fully developed subsonic turbulent jet.

Motor thermal management of electric vehicles (EVs) is becoming more significant due to its close relations to vehicle aerodynamic performance and power consumption, while computer aided engineering (CAE) plays an important role in its development. A 1D-3D coupled model is established to characterize transient thermal performance of the motor in an electric vehicle on a high performance computer (HPC) platform. The 1D motor thermal management model is integrated with the 1D powertrain model, and a 3D thermal model is established for the motor, while online data exchange is realized between the 1D and 3D models. The 1D model gives boundaries such as inlet coolant temperature, mass flowrate and motor heat generation to the 3D model, while the 3D model gives back boundaries such as heat transfer to coolant simultaneously. Transient simulations are performed for the 140kph(20°C) driving cycle, and the model is calibrated with experimental data.

Thermal management in electric vehicles (EVs) has attracted more attention due to its increasing significance, and computer aided engineering (CAE) plays an important role in its development. A 1D-3D online coupling approach is proposed to completely characterize transient thermal performance of an electric vehicle on a high performance computer (HPC) platform. The 1D thermal management model, consisting of air conditioning, motor cooling and battery cooling systems, is integrated with the 1D control strategy model and powertrain model consisting of motor, battery, driver and vehicle models. The 3D model is established for the air flow around the full vehicle and through its underhood. The 3D model gives boundaries such as heat exchanger air flowrates and heat flows on some component surfaces to the 1D model, while 1D gives back boundaries such as heat exchanger heat loads, component surface temperatures and fan speed simultaneously.

In order to investigate the soot formation process in a diesel spray flame, simultaneous imaging of soot precursor and soot particles in a transient spray flame achieved in a rapid compression machine was conducted by laser-induced fluorescence (LIF) and by laser-induced incandescence (LII) techniques. The 3rd harmonic (355nm) and the fundamental (1064nm) laser pulses from an Nd:YAG laser, between which a delay of 44ns was imposed by 13.3m of optical path difference, were used to excite LIF from soot precursor and LII from soot particles in the spray flame. The LIF and the LII were separately imaged by two image-intensified CCD cameras with identical detection wavelength of 400nm and bandwidth of 80nm. The LIF from soot precursor was mainly located in the central region of the spray flame between 40 and 55mm (270 to 370 times nozzle orifice diameter d0) from the nozzle orifice. The LII from soot particles was observed to surround the soot precursor LIF region and to extend downstream.

This paper documents the processes and methods used by the Ford GT team to meet aerodynamic targets. Methods included Computational Fluid Dynamics (CFD) analysis, wind tunnel experiments (both full-size and scale model), and on-road experiments and measurements. The goal of the team was to enhance both the high-speed stability and track performance of the GT. As a result of the development process, significant front and rear downforce was achieved while meeting the overall drag target.

A historical review of the patents and literature pertaining to 3-valve stratified charge engines is presented in this paper. This very old invention appears to be a practical approach for the “clean engine” being sought for vehicular use since it has the intrinsic capability of simultaneously giving good fuel economy and producing minimal objectionable exhaust emissions. The prime requisites of this engine are a rich prechamber charge and a very lean main chamber charge regardless of prechamber volume, nozzle diameter, valving and spark plug location. Fuel-air equivalence ratios of the charges in the two combustion chambers are significantly important in order to achieve the proper optimization. These ratios should be about 15% rich for the prechamber and 15 to 30% lean for the main chamber at the moment of ignition.

A 3-D analysis of the flow through a multihole, V.C.O. (Valve Covered Orifice) nozzle for D.I. Diesel Engine has been carried out. The analysis was performed by means of a finite element code. The nozzle comprises five injection holes. Aims of the analysis were: the investigation of the pressure drops along the conical clearance between the needle and the nozzle; the evaluation of the energy losses in the injection holes; the disclosure of the velocity profile at the injection hole outlets. the differences of flowrate for each hole with geometrical asymmetries. This kind of analisys is the first step of a more complete spray analysis; in fact, the spray from an injection hole is influenced by the injection pressure and the velocity profile. In particular, the needle lift and the needle tip deviation have been parametrized. The analysis betters both the theoretical knowledge of this kind of nozzle and the hydraulic phenomena occurring inside.

The design of reliable DPF systems has proved a complex and demanding task that is increasingly being assisted by modeling. 1-D but also 2-D (axisymmetric) modeling has already been applied in design optimization case studies, with varying degrees of success. The introduction of advanced technology SiC and cordierite filters with modular structure and the need to accurately model transient temperature and stress fields in low space velocity scenarios, made necessary the shift to 3-D modeling. In this paper, 3-D modeling is carried out in an effective and reliable way, by interfacing a well-documented and validated 1-D model with the ABAQUS commercial FEM software. The new modeling methodology proves a powerful tool in the hands of the filter and diesel exhaust system design engineer.

A three-dimensional model for premixed- charge naturally-aspirated rotary engine combustion is used to identify combustion chamber geometries that could lead to increased indicated efficiency for a lean (equivalence ratio =0.75) natural gas/air mixture. Computations were made at two rpms (1800 and 3600) and two loads (approximately 345 Kpa and 620 Kpa indicated mean effective pressure). Six configurations were studied. The configuration that gave the highest indicated efficiency has a leading pocket with a leading deep recess, two spark plugs located circumferentially on the symmetry plane (one after the minor axis and the other before), a compression ratio of 9.5, and an anti-quench feature on the trailing flank.

A three-dimensional combustion model for a direct-injection stratified-charge rotary engine is used to identify modifications to the engine that should lead to better indicated efficiency. The engine has a single spark plug positioned alongside a single-hole pilot injector in a cavity located after the minor axis and a five-hole main injector that is located before the minor axis. It is predicted that a second ignition source located upstream of the main injector will lead to an increase in indicated efficiency of 6-8% if it ignites the mixture consistently. The computations were made at high and low engine speeds and loads, covering a significant part of the practical operating range of the engine. It is also predicted that the gain in efficiency of the engine with two ignition sources would be 7-10%, instead of 6-8%, if a two-hole pilot injector is also used instead of the one-hole pilot.

A three-dimensional model for a direct injection stratified-charge rotary engine has been employed to study two modifications to the pocket geometry of the engine. In one modification, a pocket is located towards the leading edge of the rotor and is shown to produce recirculation within the pocket and faster burning. In the second modification, a two pocket rotor with two injectors and two spark plugs is studied. It appears that this should result in better utilization of the chamber air. It also appears that both modifications rhould result in higher efficiency of the direct-injected stratifiedcharge rotary engine. However extensive computations are required before a final conclusion is reached and before specific recommendations can be made.

A three-dimensional combustion model of a direct-injection stratified-charge rotary engine is used to identify modifications that might lead to better indicated efficiency. The engine, which has a five-hole main injector and a pilot injector, is predicted to achieve better indicated efficiency if a two-hole ‘rabbit-ear’ pilot injector is used instead of its present single-hole pilot injector. This rabbit-ear arrangement is predicted to increase the surface area of the early flame (on account of better distribution of the fuel), and thereby result in an increased overall burning rate. Computations were made at high and low engine speeds and loads, encompassing the practical operating range. It is concluded that the modified pilot injector will increase indicated efficiency by about 5% within the computed operating range.

The dynamics of vehicle front end crash are studied using the ADAMS dynamic simulation code. The analysis is carried out in three dimensions and can capture the behavior associated with an asymmetrical structure or impact mode. Subroutines which allow the modeling of structural crush and plastic hinge formation, contact forces and friction forces are discussed. The method is relatively inexpensive, but does require a good understanding of the problem on the part of the analyst. A discussion of the techniques that are used to model the structural system is given. The results of the analysis are compared with experimental data and the correlation is very encouraging.

An investigation of the possibility to extend the 3-dimensional modeling capabilities from conventional diesel to the HCCI combustion mode simulation was carried out. Experimental data was taken from a single cylinder engine operating with early injections for the HCCI and a split-injection (early pilot+main) for the high speed Diesel engine operation. To properly phase the HCCI mode in the experiments, high amounts of cooled EGR and a decreased compression ratio were used. In numerical simulation performed using KIVA3-V code, modified to incorporate the Detailed Chemistry Approach the same conditions were reproduced. Special attention is paid on the analysis of the events leading up to the auto-ignition, which was reasonably well predicted.

Manufacturers of heavy-duty diesel engines are facing increasingly stringent, emission standards. These standards have motivated new research efforts towards improving the performance of diesel engines. The objective of the present program is to develop a comprehensive analytical model of the diesel combustion process that can be used to explore the influence of design changes. This will enable industry to predict the effect of these changes on engine performance and emissions. A major benefit of the successful implementation of such models is that engine development time and costs would be reduced through their use. The computer model is based on the three-dimensional KIVA-II code, with state-of-the-art submodels for spray atomization, drop breakup / coalescence, multi-component fuel vaporization, spray/wall interaction, ignition and combustion, wall heat transfer, unburned HC and NOx formation, and soot and radiation.

Ever increasing specific power of diesel engines has put huge demand on effective thermal management of the pistons for the desired reliability and durability. The piston temperature control is commonly achieved by injecting cooling oil into piston galleries, but the design of the cooling system as well as the boundary conditions used in FEA simulations have so far relied mostly on empirical methods. A numerical procedure using 3D computational fluid dynamics (CFD) has therefore been developed to simulate the cooling process and to estimate the cooling efficiency of gallery. The model is able to predict the detailed oil flow and heat transfer in gallery, of different designs and engine applications, under dynamic conditions. The resulted spatially resolved heat transfer coefficient from the CFD model, with better accuracy, enables improved prediction of piston temperature in finite element analysis (FEA).

The urea Selective Catalytic Reduction (SCR) exhaust system has been proved to be the reliable aftertreatment device with the capability of reducing tail pipe NOx emission by 75% to 90%, HC by 50% and Particulate Matter (PM) by 30%. Constrained by increasingly stringent packaging envelope, flow mixing in front of substrate is becoming one of the major concerns to achieve ideal performance of higher NOx conversion and lower ammonia (NH3) slip. Three dimensional CFD simulations are performed in current study to investigate flow mixing phenomenon in a SCR system. First, for a traditional tube injector with single or multiple nozzles, the effects of mass flow rates of injected NH3 and exhaust gas on flow mixing and pressure loss are investigated. Then, a concept of ring shape injector with multiple nozzles are initiated and built for 3-D CFD simulations. The comparisons of flow mixing index and injection pressure are made between two type injectors.

The main objective of the current paper was to investigate the fluid flow and pressure loss characteristics of DPF substrates with asymmetric channels utilizing 3-D Computational Fluid Dynamics (CFD) methods. The ratio of inlet to outlet channel width is 1.2. First, CFD results of velocity and static pressure distributions inside the inlet and outlet channels are discussed for the baseline case with both forward and reversed exhaust flow. Results were also compared with the regular DPF of same cell structure and wall material properties. It was found that asymmetrical channel design has higher pressure loss. The lowest pressure loss was found for the asymmetrical channel design with smaller inlet channels. Then, the effects of DPF length and filter wall permeability on pressure loss, flow and pressure distributions were investigated.

3-D shell components are used intensively in the automotive industry. Many structural topology optimization techniques were developed to reduced the total weight of shell structures while retaining its structural performance. One common approach is to utilize the concept of the design domain, such as the homogenization method and the density function approach. In this paper, a new micro-structure based design domain method is introduced to solve 3-D shell topology optimization problems. Based on physical micro-structure model, simple closed-form expressions for effective Young's modulus and effective shear modulus are rigorously derived. Using these simple relations, topology optimization problems can be formulated and solved with sequential convex approximation algorithms. Two design examples obtained from the new method are presented.

A three-dimensional model is used to compute the flow,sprays and combustion in a stratified-charge rotary engine. Wall temperatures estimated from available measurements are used as boundary conditions for the energy equation. The computations provide local and instantaneous heat fluxes on the rotor and the rotor housing. The instantaneous heat fluxes are integrated in time over one cycle of the rotor to obtain estimates of local cycle averaged heat flux through the rotor and the rotor housing. These are then used as boundary conditions in a thermal analysis of the rotor and rotor housing with known coolant-side flow rates and heat transfer coefficients. The thermal analysis is done using a finite-element three-dimensional code which provides updated estimates of the rotor and rotor housing wall temperatures. These wall temperatures agree within ±20°C of the measured wall temperatures.