Search Results

Abstract This article presents an investigation of energy transfer, flame propagation, and emissions formation mechanisms in a four-cylinder, downsized and boosted, spark ignition engine fuelled by either directly injected compressed natural gas (DI CNG) or gasoline (GDI). Three different charge preparation strategies are examined for both fuels: stoichiometric engine operation without external dilution, stoichiometric operation with external exhaust gas recirculation (EGR), and lean burn. In this work, experiments and engine modelling are first used to analyze the energy transfer throughout the engine system. This analysis shows that an early start of fuel injection (SOI) improves fuel efficiency through lower unburned fuel energy at low loads with stoichiometric DI CNG operation.

Abstract The article compares the accuracy of different exhaust gas recirculation (EGR) correction factor models under engine conditions. The effect of EGR on the laminar burning velocity of a EURO VI E10 specification gasoline (10% Ethanol content by volume) has been back calculated from engine pressure trace data, using the Leeds University Spark Ignition Engine Data Analysis (LUSIEDA) reverse thermodynamic code. The engine pressure data ranges from 5% to 25% EGR (by mass) with the running conditions, such as spark advance and pressure at intake valve closure, changed to maintain a constant engine load of 0.79 MPa gross mean effective pressure (GMEP). Based on the experimental data, a correlation is suggested on how the laminar burning velocity reduces with increasing EGR mass fraction.

Abstract Stratified lean combustion has proven to be a promising approach for further increasing the thermal efficiency of gasoline direct injection engines in low load conditions. In this work, a new injection strategy for stratified operation mode is introduced. A side and a central-mounted solenoid multi-hole injector are simultaneously operated in a single-cylinder engine. Thermodynamic investigations show that this concept leads to improved stability, faster combustion, reduced particle number emissions, and lower fuel consumption levels compared to using only one injector. Experiments at an optical engine and three-dimensional computational fluid dynamics (CFD) simulations explain the improvements by a more compact mixture and reduced piston wetting with two injectors. Finally, the application of external EGR in combination with the above concept allows NOx emissions to be effectively kept at a low level while maintaining a stable operation.

Abstract Realizing the potential of the gasoline direct injection (GDI) concept lies in effectively stratifying the charge at different engine operating conditions. This is generally obtained by properly directing the air and fuel through carefully oriented intake port(s) and fuel spray and appropriately changing injection parameters. However, robust methods of charge stratification are essential to extend the lean operating range, particularly in small GDI engines. In this work, a novel piston shape was developed for a 200 cm3, single-cylinder, four-stroke gasoline engine to attain charge stratification. Stratification of charge is achieved even when the fuel was injected early in the intake stroke by a specially shaped wedge on the piston crown that produced twin vortices during compression and physically separated the charge into two sides in the combustion chamber.

Abstract Emission Control has always been a major concern in each and every field. An increase in emissions leads to climate change, global warming, and even various diseases. The transportation system is responsible for around 30% of emission production, of which 70% of the total atmospheric burden comes from automobiles. Recently developed emission-free electric vehicles have positively affected the levels of impurity in the environment, yet the remaining Internal Combustion Engine (ICE) vehicles on the road have been left with unchecked emissions. Traditional Catalytic Converters are widely used to reduce the emissions of vehicles. It works on the principle of converting hazardous gases emitted from the engine to less harmful carbon dioxide (CO2), nitrogen (N2), and water (H2O). It is integrated with the exhaust of the engine. High efficiency and better emission control catalytic converters are still major milestones to achieve for automotive industries.

Abstract Gasoline particulate filters (GPFs) are important aftertreatment components that enable gasoline direct injection (GDI) engines to meet European Union (EU) 6 and China 6 particulate number emissions regulations for nonvolatile particles greater than 23 nm in diameter. GPFs are rapidly becoming an integral part of the modern GDI aftertreatment system. The Active Exhaust Tuning (EXTUN) Valve is a butterfly valve placed in the tailpipe of an exhaust system that can be electronically positioned to control exhaust noise levels (decibels) under various vehicle operating conditions. This device is positioned downstream of the GPF, and variations in the tuning valve position can impact exhaust backpressures, making it difficult to monitor soot/ash accumulation or detect damage/removal of the GPF substrate. The purpose of this work is to present a unique example of subsystem control and diagnostic architecture for an exhaust system combining GPF and EXTUN.

Abstract While the hot debate keeps going about whether the internal combustion engine (ICE) will die or not, the ICE community never stopped improving the technologies that improve the fuel economy and reduce harmful emissions. Focusing on the emissions and the control system, this article reviewed the latest improvement and advances of related technologies. By firstly introducing the noteworthy emissions from ICE, this work then summarized the evolution of the related emission regulations on both light-duty and high-duty vehicles in a few major market regions. The key technologies that applied or are still under development for both carbon dioxide (CO2), nitrogen oxides (NOx), and particulate matter (PM)/particle number (PN) emissions control were reviewed in detail. Lastly, the foreseeable regulations limits and the potential challenges were discussed briefly.

Abstract Cycle-by-cycle combustion prediction in real time during engine operation can serve as a vital input for operating at optimal performance conditions and for emission control. In this work, a real-time capable physics-based combustion model has been proposed for the prediction of the heat release rate in a direct injection diesel engine. The model extends the approaches proposed earlier in the literature by considering spray dynamics such as spray penetration and Sauter mean diameter in order to calculate the mass of evaporated fuel from the spray. Wall impingement of the liquid spray is predicted by considering the liquid length based on the prevailing in-cylinder conditions. These effects are considered even after the hydraulic end of injection till the last droplet of fuel impinges on the combustion chamber wall. The fuel evaporated from the wall film and its contribution to the kinetic energy of the charge are also considered.

Abstract The variation of inflation pressure has an important effect on the longitudinal slip characteristics of tires that can affect the braking performance of the vehicle, so the influence of inflation pressure should be taken into account in high-precision tire models. However, the effects of inflation pressure and vertical load on tire force and moment characteristics are usually coupled. When the inflation pressure is changing while keeping the load constant, the tire contact patch and carcass stiffness will change at the same time, so the contribution of tread and carcass to tire traction properties cannot be decoupled so that the tire design cannot be well guided. On the contrary, if the vertical loading method is changed, the vertical deflection control is used instead of load control.

Abstract This study predicts the dynamic characteristics for tires in the development stages of a vehicle with a focus on the generated forces. In particular, this investigation proposes an approximation analysis for the deflection and contact characteristics of a pneumatic tire. This consists of an integrated model for a three-dimensional membrane ring and brush models. This model is more complex than conventional models, which resulted in increased computational costs. Because the tire dynamic characteristics affects the contact pressure, the deformation of the tread rubber caused an interaction of forces. Therefore, the tread ring deformation was defined as a summation of the mode basis functions, which expressed vibrational behavior. This approximation linearizes the energy function, which helped calculate the potential energy of the tire structure using a theoretical equation without discretization.

Abstract This study analyzes the distribution of exhaust mass pollutants emission obtained in 1,157 tests in the European driving cycle of used light-duty vehicles (LDVs). At the time of production, the tested vehicles complied with the Federal environmental requirements of the United States (USA) and were imported to Europe from North America. They included 1,109 passenger cars (PCs) and 48 light-duty trucks (LDTs), equipped with gasoline engines. In general, for measured emissions of carbon monoxide (CO), nonmethane hydrocarbons (NMHC), nitrogen oxides (NOx), and particulate matter (PM): 25% of test results for PCs do not exceed the T2B5 limits of the US Federal Standard; 43% of test results for PCs do not exceed the thresholds, designated for on-board diagnostic system (OBD) proper functioning; 45% of test results for PCs do not exceed the European Union (EU)’s former standard “Euro-5” norms.

Abstract Under contract to the EPA, Eastern Research Group analyzed light-duty vehicle OBD monitor readiness and diagnostic trouble codes (DTCs) using inspection and maintenance (I/M) data from four states. Results from roadside pullover emissions and OBD tests were also compared with same-vehicle I/M OBD results from one of the states. Analysis focused on the evaporative emissions control (evap) system, the catalytic converter (catalyst), the exhaust gas recirculation (EGR) system and the oxygen sensor and oxygen sensor heater (O2 system). Evap and catalyst monitors had similar overall readiness rates (90% to 95%), while the EGR and O2 systems had higher readiness rates (95% to 98%). Approximately 0.7% to 2.5% of inspection cycles with a “ready” evap monitor had at least one stored evap DTC, but DTC rates were under 1% for the catalyst and EGR systems, and under 1.1% for the O2 system, in the states with enforced OBD programs.

Abstract In order to improve performance and minimize pollutant emissions in gasoline turbocharged direct-injection (GTDi) engines, different injection strategies and technologies are being investigated. The inclusion of exhaust gas recirculation (EGR) and the variation of the start of injection (SOI) are some of these strategies that can influence the air-to-fuel (AF) mixture formation and consequently in the combustion process and pollutant emissions. This paper presents a complete study of the engine performance, pollutant emissions and aftertreatment efficiency that produces the SOI variation with a fixed EGR rate in a 4-cylinder, turbocharged, gasoline direct-injection engine with 2.0 L displacement. The equipment used in this study are TSI-EEPS for particle measurement and HORIBA MEXA 1230-PM for soot measurement being HORIBA MEXA 7100-DEGR with a heated line selector the system employed for regulated gaseous emission measurement and aftertreatment evaluation.

Abstract The aim of this work is to present the results achieved in the evaluation of combustion metrics using low-cost sensors for the indirect measurement of cylinder pressure. The developed transducers are piezoelectric rings placed under the spark plugs. Tests were carried out on three different engines running in various speed and load conditions. The article shows the characteristics of the signals generated by the piezo-ring sensors, compared to those coming from laboratory-grade pressure transducers: focus is to assess the achievable accuracy in the determination of frequently used combustion metrics, such as those related to knock intensity (Maximum Amplitude of Pressure Oscillations, MAPO), combustion phasing (MFB10, MFB50, …), and peak pressure.

Abstract The use of data-driven algorithms for the integration or substitution of current production sensors is becoming a consolidated trend in research and development in the automotive field. Due to the large number of variables and scenarios to consider; however, it is of paramount importance to define a consistent methodology accounting for uncertainty evaluations and preprocessing steps, that are often overlooked in naïve implementations. Among the potential applications, the use of virtual sensors for the analysis of solid emissions in transient cycles is particularly appealing for industrial applications, considering the new legislations scenario and the fact that, to our best knowledge, no robust models have been previously developed.

Abstract Emissions development work for gasoline aftertreatment systems is often conducted in a laboratory on a chassis dynamometer. In this situation, extractive sample lines are frequently connected to the aftertreatment system before and after various components, such as a three-way catalyst, selective catalytic reduction substrate, and the like. This is done to measure the conversion efficiency of the aftertreatment system components as a function of time. The time series exhaust component concentration data, also referred to as continuous data, are combined with a measure of exhaust volumetric flowrate and used to calculate mass-based emissions. As gasoline powertrains become cleaner and produce lower levels of criteria emissions, the proximity (i.e., colocated or not colocated) of the volumetric flowrate and concentration measurements may affect the accuracy of the overall mass emission calculation.

Abstract This study presents an assessment focused on benchmarking the energy distribution and engine efficiency of a pre-2014, United States Environmental Protection Agency (USEPA) 2010 emissions-compliant, heavy-duty (HD) diesel, long-haul truck engine as a reference of baseline technology. Further, the study used the baseline energy distribution as the baseline to factor in the efficiency gains of various future engine technologies to evaluate the impact of future greenhouse gas (GHG) standards on HD vehicle fuel consumption. Furthermore, the study predicted the maximum achievable fuel consumption benefit from a future engine technology that will employ breakthrough technologies that are not in the near-term production pathway of engine manufacturers. The baseline energy distribution was experimentally assessed by conducting a detailed engine dynamometer testing of an HD diesel engine over a wide range of engine operations.

Abstract Closed crankcase ventilation (CCV) systems are required in most automotive markets in order to meet emissions regulations. Such systems usually require a separator to recover oil and return it to the sump. Many end users fit improved separators in order to reduce intake/aftercooler contamination with soot/oil. This study measured clean and wet pressure drop and filter capture efficiency in 12 different crankcase oil mist separators which are commonly used for either original equipment (OE) or aftermarket fitment to passenger vehicles and four-wheel drives (≤200 kW). The filters tested spanned three different size/rating classes as well as included both branded and unbranded (imitation) models. In addition to filters, separators (often termed “catch cans”) and an OE cyclone separator were also examined. Testing was performed under controlled laboratory conditions using methods equivalent to previous work and current mist filter test standards.

Abstract This article focuses on a comparative research of the emissions discharged from four vehicles equipped with SI engines, which comply with different emission control systems (Euro 6, Euro 5, and Euro 3). The vehicles used for this work were installed with two different fuel injection technologies (direct injection and port fuel injection) and were operated with three different types of fuels (RON 95, M15, and E10). The tests were performed at the Joint Research Center (JRC) in Ispra using a state-of-the-art emissions test facility according to the European emissions legislation. The test bench included a chassis dynamometer and two different driving cycles were used: NEDC and US06.

Abstract Upcoming engine generations are characterized by both a general trend of increased specific-power and higher efficiency. This leads to increased thermal loads, compromising reliability, and simultaneously to a limited amount of heat under ordinary engine use. Heat is a valuable resource in providing passenger comfort and emission control. For these reasons the subject of engine thermal management is receiving increasing attention. This work presents a comprehensive study of the complete engine thermal behavior at relevant running conditions: rated-power, peak-torque and ordinary use. The work is further extended to the engine warm-up period. The result is a high-resolution complete engine thermal model, capable of simultaneously reporting the local temperature of any engine part, and the global engine heat balance at any engine load.