Search Results

An essential feature of the Audi Quattro permanent four-wheel drive system is in the inter-axle differential located on the hollow output shaft in the gearbox: the drive is taken from this differential forward to the front differential through the inside of the hollow shaft, and rearward to a propellor shaft driving the rear differential. The major advantages in everyday driving include improved traction and a reduced tendency toward throttle induced changes of attitude. The greater traction allows not only better progress in difficult road conditions; it also gives better acceleration in difficult traffic situations, such as when joining a busy main road. The more easily predictable handling response to throttle changes means that Quattro vehicles have better tracking stability. Altogether, the active safety and "roadability" are considerably improved.

CHEVROLET has made its new air-suspension system easily interchangeable in production line assembly with standard full-coil suspension by adopting a 4-link-type rear suspension with short and long arms. A feature of the system is the mounting of the leveling valves within the air-spring assemblies. These valves correct riding height continually at a moderate rate, regardless of whether the springs are leveling or operating in ride motion. The system provides constant frequency ride—ride comfort remains the same whether the car is occupied by the driver alone or is fully loaded.

This paper discusses the methodology setup for grill opening area prediction at the early development phase of the product development lifecycle, using a commercially available 1D simulation tool- AMESIM. Representative under hood has been modeled using Grill, Condenser, Radiator, intercooler, fan, and engine components. Vehicle velocity is used as an input to derive the airflow passing through the grill and other under-hood components based on ram air coefficient, pressure drop through different components (Grill, Heat exchanger, Fan & Engine). This airflow is used to predict the top tank temperature of the radiator. Derived airflow is correlated with airflow obtained from CFD simulation. A balance has been achieved between cooling drag & fan power consumption at different grill opening areas for target top tank temperature. Top tank temperature has been predicted at two different extreme engine heat rejection operating points.

For the thermal management of an automobile, the induced airflow becomes necessary to enable the sufficient heat transfer with ambient. In this way, the components work within the designed temperature limit. It is the engine-cooling fan that enables the induced airflow. There are two types of engine-cooling fan, one that is driven by engine itself and the other one is electrically driven. Due to ease in handling, reduced power consumption, improved emission condition, electrically operated fan is becoming increasingly popular compared to engine driven fan. The prime mover for electric engine cooling fan is DC motor. Malfunction of DC motor due to overheating will lead to engine over heat, Poor HVAC performance, overheating of other critical components in engine bay. Based upon the real world driving condition, 1D transient thermal model of engine cooling fan motor is developed. This transient model is able to predict the temperature of rotor and casing with and without holes.

The environment is one of the most important issues currently facing the world and the automobile industry is required to respond with eco-cars. To meet this requirement, the hybrid vehicle is one of the most optimal solutions. The hybrid system automatically stops engine idling (idling stop), or stops the engine during deceleration to recover energy. The engine stop however creates a problem concerning the vehicle's climate control system. Because the conventional climate control system incorporates a compressor driven by engine belt, there is almost no cooling performance while the engine is stopped. Until now, when a driver needed more cooling comfort the engine has been switched back on as a compromise measure. To realize cabin comfort that is consistent with fuel saving, a 2-way driven compressor has been developed that can be driven both by engine belt while the engine is running and by electric motor when the engine is stopped.

The demands for comfort and a cleaner environment have been increasing for the past years for motorcycle as well as car manufacturers. With the need to decrease the time-to-market, there is a clear drive to apply CAE-based methods in order to evaluate new designs and to propose design changes that solve any identified problems. More specifically, the demands on the comfort of the rider are not only related to ride & handling and vibration levels(1), but also to the noise levels generated by the motorcycle. This paper presents the virtual modeling of one-cylinder engine of a motorcycle that identifies the mechanism behind the generation of an annoying noise. Furthermore, different possible design changes were evaluated in order to solve the problem. A combined experimental and numerical approach was followed to achieve this. Experiments were used to identify important parameters that determine the engine behavior and thus are critical for the modeling of such an engine.

This paper examines the powertrain and braking efficiency of a wide spectrum of light duty vehicles to illustrate the range of efficiencies that exist and to isolate the contribution of hybrid and non-hybrid powertrains in reducing fuel consumption. The paper also examines the change in vehicle energy demands, e.g. aerodynamics and rolling resistance from 2005 models to 2010 models to highlight the role that vehicle energy consumption reduction plays in determining total fuel consumption. EPA fuel economy certification data is analyzed using the metrics of vehicle limited fuel consumption and powertrain and braking efficiency. From the data, conclusions are drawn to create a list of the ten most efficient powertrains, based on the powertrain and braking efficiency metric, and the ten vehicles with the lowest vehicle limited fuel consumption. These metrics provide an informative basis for current and future technology evaluations.

Contact our Energy & Propulsion Conference & Exhibition team for more information.

Contact our Energy & Propulsion Conference & Exhibition team for more information.

Showcase your products and expertise while promoting your business at the Energy & Propulsion Conference & Exhibition.

Showcase your products and expertise while promoting your business at the Energy & Propulsion Conference & Exhibition.

Contact our Energy & Propulsion Conference & Exhibition team for more information.

Request information from our sales team on how you can exhibit or sponsor at the SAE Powertrains, Fuels & Lubricants Conference & Exhibition.

Request information from our sales team on how you can exhibit or sponsor at the SAE Powertrains, Fuels & Lubricants Conference & Exhibition.

Due to the general requirements in the automotive industry to reduce the power consumption, fuel consumption rate and CO2 emission a new HID (High Intensity Discharge) bulb with only 25W is under development for front lighting systems. A first headlamp integrated in a hybrid vehicle is now launched as a first application in the market. The current regulation in ECE allows to get rid of the mandatory headlamp cleaning system and the automatic leveling requirement once the 25W HID bulb is applied. The reason for this is the objective luminous flux of the 25W HID bulb, which emits less than 2000 lm, a boundary defined in the regulation, where a headlamp cleaning and an automatic leveling is requested. That simplifies especially the integration in smaller vehicles and electric and hybrid vehicles. The paper describes the special design of the headlamp, the projector unit, the light performance, packaging advantages and future outlook of further applications in the near future.

This paper presents a novel battery degradation model based on empirical data from the Racing Green Endurance project. Using the rainflow-counting algorithm, battery charge and discharge data from an electric vehicle has been studied in order to establish more reliable and more accurate predictions for capacity and power fade of automotive traction batteries than those currently available. It is shown that for the particular lithium-iron phosphate (LiFePO₄) batteries, capacity fade is 5.8% after 87 cycles. After 3,000 cycles it is estimated to be 32%. Both capacity and power fade strongly depend on cumulative energy throughput, maximum C-rate as well as temperature.

The upcoming latest 3-wet Technology is the most ideal design for a Green field project as well as for a brown field facility which provides the best of both worlds. The foremost take away for a brown field project emanates from this technology which demands a smaller foot prints & hence could accommodates a capacity higher than what was perceived during the green field project planning thus saving millions of dollar of investment & giving that extra capacity which today the BRIC countries are thriving for. Apart from making the ideal investment choice, 3 Wet Technology provides impetus to business case in terms of reduction of VOC emission, Energy consumption, Material and labor cost and gaining on Green Environment front as well as leading to smart and Efficient-Paint-Process. The paper depicts the journey of roll out of 3-Wet process in Ford India and creating the bench mark in terms of product quality and process standards and manufacturing practices.

In order to improve the fit and comfort of helmets, we developed digital head models that represent the anthropometric and morphometric variability found in the U.S. Navy. We analyzed the size and shape variation using two related approaches. First, we used Procrustes superimposition, which minimizes the distances between all landmarks of all subjects. This allowed us to visualize the variation in landmark distribution of the face and to test for statistical differences. Second, we extracted curvatures along the surface of the head. This allowed us to characterize the variation in the shape of the head. To create a series of sized digital models, we used principal component analysis (PCA) to organize the variation in both the traditional measurements as well as the locations of the 3D landmarks. Using an adaptation of multivariate accommodation modeling we identified representative individuals who characterize 95% of the variation in size and shape.

The vehicle Heating, Ventilation and Air conditioning (HVAC) system is designed to meet both the safety and thermal comfort requirements of the passengers inside the cabin. The thermal comfort requirement, however, is highly subjective and is usually met objectively by carrying out time dependent mapping of parameters like the velocity and temperature at various in-cabin locations. These target parameters are simulated for the vehicle interior for a case of hot soaking and its subsequent cool-down to test the efficacy of the AC system. Typically, AC performance is judged by air temperature at passenger locations, thermal comfort estimation along with time to reach comfortable condition for human. Simulating long transient vehicle cabin for thermal comfort evaluation is computationally expensive and involves complex cabin material modelling.

Today's agri-businessman is challenged to improve his efficiency to meet higher operating costs and to counter the effects of inflation. New concepts in John Deere's line of 4-wheel-drive tractors are targeted toward this goal and provide increased productivity through power increases, improved fuel economy, comfortable convenient operator environment and controls, increased hydraulic power, improved serviceability and repairability and monitoring of more critical vehicle functions.