Search Results

This analysis applies to crane types as covered by Power Crane and Shovel Association Standard Number Two, Mobile Hydraulic Crane Standards and ANSI B30.15; refer to 5.1.

This analysis applies to crane types as covered by ASME B30.5.

This analysis applies to crane types as covered by ASME B30.5.

The procedure applies to heavy vehicles weighing more than 11 800 kg (26 000 lb) and particularly to those vehicles having two or more articulation joints that allow rotation in a horizontal plane. The procedure pertains to the lateral directional response of multi-articulated vehicles in avoidance maneuvers performed at highway speeds without braking.

The test procedure applies to roll coupled units such as straight trucks, tractor semitrailers, full trailers, B-trains, etc. The test is aimed at evaluating the level of lateral acceleration required to rollover a vehicle or a roll-coupled unit of a vehicle in a steady turning situation. Transient, vibratory, or dynamic rollover situations are not simulated by this test. Furthermore, the accuracy of the test decreases as the tilt angle increases, although this is a small effect at the levels of tilt angle used in testing heavy trucks. The test accuracy is accepted for vehicles that will rollover at lateral acceleration levels below 0.5 g corresponding to a tilt table angle of less than approximately 27 degrees. Even so, the results for heavy trucks with rollover thresholds greater than 0.5 g could be used for comparing their relative static roll stability.

The test procedure applies to roll coupled units such as straight trucks, tractor semitrailers, full trailers, B-trains, etc. The test is aimed at evaluating the level of lateral acceleration required to rollover a vehicle or a roll-coupled unit of a vehicle in a steady turning situation. Transient, vibratory, or dynamic rollover situations are not simulated by this test. Furthermore, the accuracy of the test decreases as the tilt angle increases, although this is a small effect at the levels of tilt angle used in testing heavy trucks. The test accuracy is accepted for vehicles that will rollover at lateral acceleration levels below 0.5 g corresponding to a tilt table angle of less than approximately 27 degrees. Even so, the results for heavy trucks with rollover thresholds greater than 0.5 g could be used for comparing their relative static roll stability.

This SAE Recommended Practice establishes the Antilock Brake System [ABS] sensor interface and envelope dimensions for standardizing the location of the ABS rings mounted on the inner end of spoke wheels, hubs and hub-rotor assemblies on the following axle designations. a FF b FL c FC d FH e L f R g U h W j N k P

This SAE Recommended Practice establishes the Antilock Brake System [ABS] sensor interface and envelope dimensions for standardizing the location of the ABS rings mounted on the inner end of spoke wheels, hubs and hub-rotor assemblies on the following axle designations. a FF b FL c FC d FH e L f R g U h W j N k P

This SAE Recommended Practice establishes the Antilock Brake System [ABS] sensor interface and envelope dimensions for standardizing the location of the ABS rings mounted on the inner end of the hub on the following axle designations. a FF b FL c L d R e U f W g N h P

This recommended practice covers the criteria for steps, ladders, walkways, platforms, grab rails (handrails), grab irons, guardrails, and entrance openings as they relate to aiding the operator and/or servicemen in performing their functions on the vehicle.

Minimum criteria are provided for steps, stairways, ladders, walkways, platforms, handrails, handholds, guardrails, and entrance openings which permit ingress to and egress from operator, inspection, or service platforms on off-road work machines parked in accordance with the manufacturer's instructions.

Minimum criteria are provided for steps, stairways, ladders, walkways, platforms, handrails, handholds, guardrails, and entrance openings which permit ingress to and egress from operator, inspection, maintenance or service platforms on off-road work machines parked in accordance with the manufacturer's instructions.

Minimum criteria are provided for steps, stairways, ladders, walkways, platforms, handrails, handholds, guardrails, and entrance openings which permit ingress to and egress from operator, inspection, or service platform on off-road work machines parked in accordance with the manufacturer’s instructions.

This recommendation establishes a uniform test procedure for evaluating performance of agricultural equipment operator enclosure pressurization systems.

The purpose of this information report is to establish dynamic indices which are to be used only for calculating the travel speed of the agricultural tractor during worldwide homologation procedures.