Search Results

This paper summarizes the techniques and guidelines which were used to reduce the driver perceived noise level of a 145-210 HP series of agricultural tractors. Graphs of case study test results and comments on subjective noise quality are provided to guide the acoustic novice through the complexities of the vehicle sound environment in a methodical problem solving format.

Contact the appropriate representative of the 2023 Noise and Vibration Conference and Exhibition.

Health related problems in over populated areas are a major concern and as such, there are specific legislations for noise generated by transport vehicles. In diesel powered commercial vehicles, the source for noise are mainly related to rolling, transmission, aerodynamics and engine. Considering internal combustion engine, three factors can be highlighted as major noise source: combustion, mechanical and tailpipe. The tailpipe noise is considered as the noise radiated from the open terminations of intake and exhaust systems, caused by both pressure pulses propagating to the open ends of the duct systems, and by vortex shedding as the burst leaves the tailpipe (flow generated noise). In order to reduce noise generated by vehicles, it is important to investigate the gas interactions and what can be improved in exhaust line design during the product development phase.

Diesel injection equipment is required to be more accurate and higher in pressure to meet the increasingly strict emission, fuel consumption regulations and higher engine performance. It also needs to achieve a number of requirements such as robustness against diversified market fuels, easy installation to engine, etc.

The new 5480 Reach Truck, designed at Dynamic Industries, introduces a movable frame between the main frame and the telescopic boom. The use of this movable frame allows the usually fixed boom pivot to be elevated for greater lifting heights with smaller boom sections. By combining the motions of the boom and the movable frame, horizontal motion at the boom tip is possible without moving the truck. With the movable frame, the total machine height and length can be reduced for a given lifting goal. Another advantage of the movable frame is the ability to reach further below grade than is now possible in the industry. The 5480 Reach Truck has a maximum lift of 54 feet (16.5 meters) and can reach 24 feet (7.3 meters) below-grade.

The LTL-900 Transi-Lift crane features front and rear crawler-mounted load platforms connected with a hoist-supporting five foot diameter pipe section. The pin-together main boom is available in lengths up to 400 feet and completely disassembles for ease of transport to and from the jobsite. The crane requires three operators and can hoist, boom, swing and travel simultaneously with maximum loads. Upending, moving and setting large refinery vessels is facilitated by the mobility of the crawler-supported crane on unprepared surfaces. Up to 1000 tons of 36 ton concrete beams or equivalent are required as counterweight to develop the ANSI B30.5 approved capacities.

A unique shuttle bus is being constructed by Minicars, Inc., and Walter Vetter Karosserie-werk for Denver’s Transitway/Mall. The bus is designed for frequent stop, low speed service in a downtown pedestrian environment. It features a very low floor and multiple wide doors for rapid passenger boarding and deboarding. Two versions will be supplied for comparative evalation, a low noise diesel configuration and a battery-electric configuration. Either version can subsequently be converted to the alternative propulsion system.

The paper addresses some aspects of an ongoing research on a commercial compact excavator. The interest is focused on the analysis and modelling of the whole hydraulic circuit that, beside a load sensing variable displacement pump, features a stack of nine proportional directional control valves modules of which seven are of the load sensing type. Loads being sensed are the boom swing, boom, stick and bucket, right and left track motors and work tools; instead, the blade and the turret swing users do not contribute to the load sensing signal. Of specific interest are the peculiarities that were observed in the stack. In fact, to develop an accurate AMESim modelling, the stack was dismantled and all modules analysed and represented in a CAD environment as 3D parts. The load sensing flow generation unit was replaced on the vehicle by another one whose analysis and modelling have been developed using available design and experimental data.

Hundreds of millions of micromachined, piezoresistive Manifold Absolute Pressure (MAP) sensors have been produced to reduce pollution and improve fuel efficiency in engine control systems. Other vehicle applications for micromachined pressure sensors include monitoring turbo pressure, barometric pressure, fuel tank leakage, fuel rail pressure and tire pressure. Exhaust gas recirculation and even door compression for side impact detection are employing micromachined silicon pressure sensors. Piezoresistive pressure sensors have dominated the automotive market to date. Practical micromachined capacitive pressure sensors have recently been developed and could replace the piezoresistive sensor in many applications. This paper will examine the advantages of both pressure sensing technologies, and discuss applications that an inexpensive capacitive pressure sensor will open up.

Water-cooled charge air cooling is being considered as part of various technology solutions in response to 2007 US, 2010 US, EU4 and EU5 emissions standards. As manufacturers determine appropriate engine and vehicle solutions to meet the upcoming emissions standards, charge air cooling requirements are increasing due to higher turbocharger outlet temperatures and pressures, higher EGR rates, and requests for intake manifold temperature control to manage combustion and exhaust temperatures. Valeo and EMP have collaborated on the development and testing of a water cooled charge air cooler (WCCAC), controlled by a 12 volt brushless motor coolant pump. The system design addresses material temperature limitations of air-air aluminum CAC's and has the potential to simplify the packaging of the air induction system.

Emissions and in-cylinder pressure traces are used to compare the relative importance of soot formation and soot oxidation in a heavy-duty diesel engine. The equivalence ratio at the lift-off length is estimated with an empirical correlation and an idealized model of diesel spray. No correlation is found between the equivalence ratio at lift-off and the soot emissions. This confirms that trends in soot emissions cannot be directly understood by the soot formation process. The coupling between soot emission levels and late heat release after end of injection is also studied. A regression model describing soot emissions as function of global engine parameters influencing soot oxidation is proposed. Overall, the results of this analysis indicate that soot emissions can be understood in terms of the efficiency of the oxidation process.

The paper describes a simple, modified, direct method for the design of high pressure ratio centrifugal compressor impellers, using a prescribed relative velocity distribution. Based on certain simplifying assumptions, the equations of equilibrium are written in terms of the relative velocity components in the radial, axial and tangential directions. These were then solved in a step by step manner along the mean streamline to give the channel shape. An example impeller is shown, which was designed using this method, its geometric proportions appear to be acceptable.

A distributed sensor is created to sense the rate of change in deflection of beam-like structures such as crane booms. This sensor will be useful in electrohydraulic compensation of boom deflections. The sensor is made of an array of strain-sensitive segments such as strain gages or piezoelectric film. In this example, segments of piezoelectric film convert strains on the surface of a vibrating beam into electrical outputs. These outputs are connected to low impedance signal conditioners. The output of the signal conditioners are then interpolated with a weighting vector that incorporates Lagrange polynomials, specified boundary conditions, and the desired location(s) of measurement. A simple linear combiner circuit combines the electrical outputs into the deflection velocity at the desired points.

This paper outlines the techniques used to install both a full scale and a half scale tractor-trailer model in the 9×9 meter National Research Council of Canada wind tunnel in Ottawa, Canada. The objectives were to measure the cooling drag of an active cooling system and to investigate the aerodynamic testing limits of long, yawed models inside a solid wall wind tunnel. The tunnel interference problem is discussed as it pertains to the upstream boundary, test section floor, downstream boundary, ceiling and side walls and tractor-trailer surface pressure measurements. A potential solution to the problem, however, is the subject of a follow-up paper.

This article introduce a kind of displacement sensor and the matching circuits with it. The sensor can be used to measure the displacement of cartridge insert valve in the medium of pressure with amplitude ranged from 0 Mpa to 32 Mpa.

The need for pressure feed back in hydraulic servo systems has long been recognized. Until recently however such transduction has not been practical from the perspectives of both price and performance. This paper describes the simplification of a proven design to reach a cost effective solution to this problem. A test program verifying performance under actual working conditions is described.

The transition from ICE to electric power trains in new vehicles along with the application of advanced active and passive noise reduction solutions has intensified the perception of noise sources not directly linked to the propulsion system. This includes road noise as amplified by the tire cavity resonance. This resonance mainly depends on tire geometry, air temperature inside the tire and vehicle speed and is increasingly audible for larger wheels and heavier vehicles, as they are typical for current electrical SUV designs. Active technologies can be applied to significantly reduce narrow band tire cavity noise with low costs and minimal weight increase. Like ANC systems for ICE powertrains, they make use of the audio system in the vehicle. In this paper, a novel low-cost system for road induced tire cavity noise control (RTNC) is presented that reduces the tire cavity resonance noise inside a car cabin.

Proton Exchange Fuel Cells (PEMFCs) are considered one of the most prominent technologies to decarbonize the transportation sector, with emphasis on long-haul/long-range trucks, off-highway, maritime and railway. The flow field of reactants is dictated by the layout of machined channels in the bipolar plates, and several established designs (e.g., parallel channels, single/multi-pass serpentine) coexist both in research and industry. In this context, the flow behavior at cathode embodies multiple complexities, namely an accurate control of the inlet/outlet humidity for optimal membrane hydration, pressure losses, water removal at high current density, and the limitation of laminar regime. However, a robust methodology is missing to compare and quantify such aspects among the candidate designs, resulting in a variety of configurations in use with no justification of the specific choice.

With India achieving the BSVI milestone, the diesel particulate filter (DPF) has become an imperative component of a modern diesel engine. A DPF system is a device designed to trap soot from exhaust gas of the diesel engine and demands periodic regeneration events to oxidize the accumulated soot particles. The regeneration event is triggered either based on the soot mass limit of the filter or the delta pressure across it. For a Heavy Duty Diesel Engine (HDDE), pressure difference across the DPF is not usually reliable as the size of the DPF is large enough compared to the DPF used ina passenger vehicle diesel engine. Also, the pressure difference across DPF is a function of exhaust mass flow and thus it makes it difficult to make an accurate call for active regeneration. This demands for a very accurate soot estimation model and it plays a vital role in a successful regeneration event.

A multi-sensing device with a piezoresistive pressure sensor for hydraulic system control was developed, applied to a hydraulic belt conveyor and tested. One single pressure sensor was installed inside a hydraulic motor. By analyzing the output signals, the following engineering variables were measured and could be analyzed: running speed, torque, absolute displacement, horsepower, pressure, mass flow rate of conveyed materials and even malfunction diagnosis. High speed resolution, torque and mass flow rate measurements are focused on in this paper. Based on data sampling rates and windows, high resolution speed data from a hydraulic motor sensor was measured. Relationships between mass flow rates on the conveyor belt and torques due to loading under various situations are presented.