Refine Your Search

Date

Date

Topic

Topic

Motor Vehicle Council Safety Aircraft Fixed-wing aircraft Management and Organizations

Search Results

Viewing 1 to 20 of 50
123Next >Last >>
Sort by title
Standard

Considerations for Suspension Modification
2019-10-09
CURRENT
J2492_201910
The scope of this document is limited specifically to the following types of passenger vehicles: automobiles, light trucks, and sport/utility vehicles. This document addresses modifications as they apply to legal use of the vehicle, and examines suspension modification as it applies to stock (as manufactured) ride height, and changed (raised or lowered) ride height. Note that modifications of ride height are considered, exclusive of wheel and/or tire modifications, which can also have potentially serious side effects, and are outside the scope of this document.
Standard

Considerations for Suspension Modification
1999-06-01
HISTORICAL
J2492_199906
The scope of this document is limited specifically to the following types of passenger vehicles: automobiles, light trucks, and sport/utility vehicles. This document addresses modifications as they apply to legal use of the vehicle, and examines suspension modification as it applies to stock (as manufactured) ride height, and changed (raised or lowered) ride height. Note that modifications of ride height are considered, exclusive of wheel and/or tire modifications, which can also have potentially serious side effects, and are outside the scope of this document.
Standard

DYNAMIC TEST PROCEDURE - TYPE 1 AND TYPE 2 SEAT BELT ASSEMBLIES
1970-01-01
HISTORICAL
J117_197001
This SAE Recommended Practice establishes a dynamic test procedure for evaluating Type 1 lap belt assemblies for pelvic restraints and Type 2 assemblies for combination pelvic and upper torso restraints, as defined in SAE J4c. Uniform test requirements, test procedures, a seat belt assembly loading device, and data recording requirements are specified. The intent of the recommended practice is to provide an acceptance procedure employing a dynamic test method for determining the ability of seat belt assemblies to meet minimal requirements for restraining a seat belt assembly loading device. A simple dynamic test is described which will yield repeatable and comparable results while simulating the loading condition a seat belt assembly is subjected to in a frontal accident. The impact conditions generate belt loads representative of those obtained in a motor vehicle striking a rigid barrier head on at 30 mph as stated in SAE J850.
Standard

MOTOR VEHICLE SEATING SYSTEMS
1968-07-01
HISTORICAL
J879B_196807
This SAE Recommended Practice establishes uniform test procedures and certain minimum performance requirements for motor vehicle seats and seat adjusters. It is limited to tests that can be conducted on uniform test fixtures and equipment available in commercial laboratory test facilities. This practice includes a minimum requirement for horizontal forward loads encountered in vehicle forward impacts, and horizontal loads obtained by impacting the vehicle from the rear. The requirements and test procedures in this recommended practice reflect current technology and industry experience. It is intended to subject this recommended practice to a continuing review and revision as technology advances and experience is expanded.
Standard

Motor Vehicle Seat Belt Anchorages - Design Recommendations
2022-07-08
CURRENT
J383_202207
This SAE Recommended Practice specifies design recommendations for the location of seat belt assembly anchorages which will promote proper transfer of occupant restraint forces on the strongest parts of the human anatomy to the vehicle or seat structure. Test procedures are specified in SAE J384.
Standard

Motor Vehicle Seat Belt Anchorages - Design Recommendations
2014-10-28
HISTORICAL
J383_201410
This SAE Recommended Practice specifies design recommendations for the location of seat belt assembly anchorages which will promote proper transfer of occupant restraint forces on the strongest parts of the human anatomy to the vehicle or seat structure. Test procedures are specified in SAE J384.
Standard

Motor Vehicle Seat Belt Anchorages - Performance Requirements
2014-07-02
CURRENT
J385_201407
This SAE Recommended Practice specifies performance requirements for the strength of seat belt anchorages attached to vehicle structure or to the seat assemblies as installed in the motor vehicle. (This document supersedes the Performance Requirements Section of SAE J787b.) Design recommendations and test procedures are specified in SAE J383 and SAE J384, respectively.
Standard

Motor Vehicle Seat Belt Anchorages - Test Procedure
2022-07-08
CURRENT
J384_202207
This SAE Recommended Practice specifies performance requirements and test procedures for the strength and location of seat belt assembly anchorages. It applies to seat belt anchorages attached to vehicle body structure or to seat assemblies in the vehicle. Design Considerations are specified in SAE J383.
Standard

Motor Vehicle Seat Belt Anchorages - Test Procedure
2014-10-28
HISTORICAL
J384_201410
This SAE Recommended Practice specifies performance requirements and test procedures for the strength and location of seat belt assembly anchorages. It applies to seat belt anchorages attached to vehicle body structure or to seat assemblies in the vehicle. Design Considerations are specified in SAE J383.
Standard

Motor Vehicle Seat Belt Assembly Installation
2009-02-25
CURRENT
J800_200902
This SAE Recommended Practice provides general installation instructions for aftermarket, universal type seat belt assemblies for installation in passenger cars, trucks, buses, and multipurpose passenger vehicles. This SAE document is intended to provide guidance in the installation of seat belt assemblies meeting the requirements of Part 571.209 of Title 49 of the Code of Federal Regulations as established by the National Highway Traffic Safety Administration.
Standard

Motor Vehicle Seating Systems
2019-10-02
CURRENT
J879B_201910
This SAE Recommended Practice establishes uniform test procedures and certain minimum performance requirements for motor vehicle seats and seat adjusters. It is limited to tests that can be conducted on uniform test fixtures and equipment available in commercial laboratory test facilities. This practice includes a minimum requirement for horizontal forward loads encountered in vehicle forward impacts, and horizontal loads obtained by impacting the vehicle from the rear. The requirements and test procedures in this recommended practice reflect current technology and industry experience. It is intended to subject this recommended practice to a continuing review and revision as technology advances and experience is expanded.
Standard

New-Vehicle Collision Repair Information
2019-10-28
CURRENT
J2376_201910
This SAE Recommended Practice defines the various types of information required by the collision repair industry to properly restore light-duty, highway vehicles to their pre-accident condition. Procedures and specifications are defined for damage-related repairs to body, mechanical, electrical, steering, suspension, and safety systems. The distribution method and publication timeliness are also considered.
Standard

New-Vehicle Collision Repair Information
2011-05-16
HISTORICAL
J2376_201105
This SAE Recommended Practice defines the various types of information required by the collision repair industry to properly restore light-duty, highway vehicles to their pre-accident condition. Procedures and specifications are defined for damage-related repairs to body, mechanical, electrical, steering, suspension, and safety systems. The distribution method and publication timeliness are also considered.
Standard

Paint and Trim Code Location
2019-10-24
CURRENT
J2235_201910
This SAE Recommended Practice is designed to provide readily accessible paint and trim code information on all passenger vehicles, lightweight trucks, and vans in a way that minimizes the time and effort required to locate and effectively use that information for body repair, parts ordering, vehicle maintenance, and information systems.
Standard

Paint and Trim Code Location
2006-11-13
HISTORICAL
J2235_200611
This SAE Recommended Practice is designed to provide readily accessible paint and trim code information on all passenger vehicles, lightweight trucks, and vans in a way that minimizes the time and effort required to locate and effectively use that information for body repair, parts ordering, vehicle maintenance, and information systems.
Standard

Recommended Design and Performance Standard for Seats with Integrated Lap and Shoulder Restraints
2012-09-12
CURRENT
J2287_201209
This SAE Recommended Practice defines minimum performance standards, qualification requirements, and minimum documentation requirements for Integrated Lap and Shoulder Restraint (to) equipped Seats (IL&SRTS). The goal is to achieve comfort, durability, and occupant protection under expected and foreseeable normal operation loads. The document attempts to define test and evaluation criteria to demonstrate performance at peak operational loads, while attempting to maintain the seat’s ability to meet loads set forth in FMVSS 207, 210, and ECE 14, 16, and 17. This document also provides guidance for design by enumerating certain design goals to enhance comfort, serviceability, and safety. Guidance for test procedures, measurements, equipment, and interpretation of results may be presented to promote uniform techniques and to achieve acceptable data.
Standard

Recommended Practice for Optimizing Automobile Damageability and Repairability
2016-02-03
HISTORICAL
J1555_201602
This SAE Recommended Practice applies to all portions of the vehicle, but design efforts should focus on components and systems with the highest contribution to the overall average repair cost (see 3.7). The costs to be minimized include not only insurance premiums, but also out-of-pocket costs incurred by the owner. Damageability, repairability, serviceability and diagnostics are inter-related. Some repairability, serviceability and diagnostics operations may be required for collision or comprehensive loss-related causes only. Some operations may be for non-collision-related causes only (warranty, scheduled maintenance, non-scheduled maintenance, etc.). Some may be required for both causes. The scope of this document deals with only those operations that involve collision and comprehensive insurance loss repairs.
123Next >Last >>
X