Search Results

Diesel engines, especially CR (Common Rail) DI (Direct Injection) TCI (Turbo Charged Inter-cooled), share a wide acceptance in the passenger car market due to the enormous torque and flexibility at low engine speed. A pre - condition for the use of a diesel engine in a motorcycle is that the disadvantages like combustion noise and visible smoke are reduced or eliminated. Moreover the fuel economy and performance characteristics of a diesel engine are dedicated to be used in a touring or large displacement motorcycle. The AVL engine concept is the first high performance diesel engine to be specially designed for motorcycles in terms of packaging and styling. To compensate for the limited engine speed range a gearbox with a wide ratio spread is required. This leads to a manual transmission with at least 6 gears or an automatic transmission. For the AVL concept an AMT (Automated Manual Transmission) was selected.

Governmental assurance documentation bibliography updated; new tabulation effective as of April 1, 1967. Latest revision indicated in all instances, but no attempt was made to list supplements or amendments. Department of Defense Index of Specifications and Standards (DODISS) published annually in three parts (alphabetic, numerical, and listing of Federal Supply Classification following unclassified documents.

General Motors Powertrain Division has developed the next generation big block V8 engine for introduction in the 1996 model year. In addition to meeting tighter emission and on-board diagnostic legislation, this engine evolved to meet both customer requirements and competitive challenges. Starting with the proven dependability of the time tested big block V8, goals were set to substantially increase the power, torque, fuel economy and overall pleaseability of GM's large load capacity gasoline engine. The need for this new engine to meet packaging requirements in many vehicle platforms, both truck and OEM, as well as a requirement for minimal additional heat rejection over the engine being replaced, placed additional constraints on the design.

General Motors Powertrain Group (GMPTG) has developed an all new small block V8 engine, designated LS1, for introduction into the 1997 Corvette. This engine was designed to meet both customer requirements and competitive challenges while also meeting the ever increasing legislated requirements of emissions and fuel economy. This 5.7L V8 provides increased power and torque while delivering higher fuel economy. In addition, improvements in both QRD and NVH characteristics were made while meeting packaging constraints and achieving significant mass reductions.

After the first appearance of LED rear lamps, which employed mainly two-dimensional arrays of LEDs, the request of stylists and OEMs to have three-dimensional LED alignment has increased strongly. Development of more powerful LEDs and new packaging and assembly technologies now allows for a three-dimensional assembly of the LEDs, giving an impression of depth and enabling the LEDs to follow even extreme curvatures. This gives great customer satisfaction in terms of styling, but the disadvantage is that the cost for the three-dimensional LED alignment increases significantly. To counteract this development, we have developed a light guide technology approach (so-called 2.5 D) to combine a cost efficient LED assembly process with the flexibility of a 3 D arrangement of the light sources. Thus, we can use standard planar FR4 (Flame Resistant 4) LED printed circuit boards with arbitrary LEDs and do not depend on a certain assembly technology.

This paper documents the processes and methods used by the Ford GT team to meet aerodynamic targets. Methods included Computational Fluid Dynamics (CFD) analysis, wind tunnel experiments (both full-size and scale model), and on-road experiments and measurements. The goal of the team was to enhance both the high-speed stability and track performance of the GT. As a result of the development process, significant front and rear downforce was achieved while meeting the overall drag target.

This SAE Aerospace Information Report (AIR) describes field-level procedures to determine if 400 Hz electrical connections for external power may have been subjected to excessive wear, which may result in inadequate disengagement forces.

Electrical Air Conditioning Systems for 42 V vehicles will provide many benefits in terms of Environment protection, car Architecture, cabin Comfort and overall Safety. E-A/C Systems essentially differ from conventional ones by the use of electrical compressors. First of all, they will be particularly well adapted to new powertrains, helping to make them more environmentally friendly. Accurate control and high efficiency under the most common thermal conditions will reduce the A/C impact on fuel consumption. Besides, higher sealing integrity will cut emissions of refrigerant during normal operation and maintenance. Secondly, the use of an electrically driven compressor (EDC) will suppress a belt, and will reduce the packaging constraints. This will help to design new vehicle architectures. Thirdly, the electrification of air conditioning will allow better thermal comfort. In particular, E-A/C Systems provide a good opportunity for cabin pre-conditioning.

Multiple automotive systems are now being developed which require an imager or vision chip to provide information regarding vehicle surroundings, vehicle performance, and vehicle passenger compartment status. Applications include lane departure, lane tracking, collision avoidance, as well as occupant position, impaired driver, and occupant identification. These applications share many requirements, including robust design, tolerance for the automotive environment, built in self-test, wide dynamic range, and low cost. In addition, each application has unique requirements for resolution, sensitivity, imager aspect ratio, and output format. In many cases, output will go directly to vehicle systems for processing, without ever being displayed to the driver. Commercial imager chips do not address this wide spectrum of requirements. A CMOS imager chip has been designed to address these unique automotive requirements.

The development of future automotive electronic systems requires new concepts in the software architecture, development methodology and information exchange. At Bosch an XML and MSR based technology is applied to achieve a consistent information handling throughout the entire software development process. This approach enables the tool independent exchange of information and documentation between the involved development partners. This paper presents the software architecture, the specification of software components in XML, the process steps, an example and an exchange scenario with an external development partner.

This work presents the implementation and validation efforts of a 3D ice accretion solver for aeronautical applications, MESS3D, based on the advanced Messinger model. The solver is designed to deal with both liquid phase and ice crystal cloud conditions. In order to extend the Messinger model to 3D applications, an algorithm for the water run-back distribution on the surface was implemented, in place of an air flow stagnation line search algorithm, which is straightforward in 2D applications, but more complicated in 3D. The developed algorithm aims to distribute the run-back water in directions determined by air pressure gradients or shear forces. The data structure chosen for MESS3D allows high flexibility since it can manage the necessary input solutions on surface grids coming from both structured and unstructured solvers, regardless the number of edges per surface cells.

In practical applications of ammonia SCR aftertreatment systems using urea as the reductant storage compound, one major difficulty is the often constrained packaging envelope. As a consequence, complete mixing of the urea solution into the exhaust gas stream as well as uniform flow and reductant distribution profiles across the catalyst inlet face are difficult to achieve. This paper discusses a modeling approach, where a combination of 3D CFD and a lumped parameter SCR model enables the prediction of system performance, even with non-uniform exhaust flow and ammonia distribution profiles. From the urea injection nozzle to SCR catalyst exit, each step in the modeling process is described and validated individually. Finally the modeling approach was applied to a design study where the performance of a range of urea-exhaust gas mixing sections was evaluated.

Tire tread separation events, a category of tire disablements, can be sub-categorized into two main types of separations. These include full tread separations, in which the tread around the entire circumference of the tire separates from the tire carcass, and partial tread separations, in which a portion of the tread separates and the flap remains attached to the tire for an extended period of time. In either case, the tire can remain inflated or lose air. Relatively, there have been few partial tire tread separation tests presented in the literature compared to full tread separation tests. In this study, the results of 25 full and partial tire tread separation tests, conducted with a variety of vehicles at highway speeds, are reported. Cases in which the tire remains inflated and loses air pressure are both considered. The testing was performed on a straight section of road and primarily focused on rear tire disablements.

Accumulation of fuel, water, acids, insolubles, and metals in engine oil is documented and compared for variable-fueled (fuel containing up to 85 percent methanol) and gasoline-fueled vehicles in short-trip service. The oil temperature at which various contaminants are removed is noted. As a consequence of emulsion formation, the viscosity of the oil in the M85-fueled vehicles increased. Due to the presence of gasoline, the viscosity of the oil in the gasoline-fueled vehicles decreased. Equations were developed to explain both the viscosity reduction due to gasoline and the viscosity increase due to emulsion-forming contaminants (water and methanol).

A comparison of various numerical tools and techniques was performed for calculating the lightning indirect effects to composite structures and internal systems. This paper is a summary of the initial comparison results. Detailed results of each technique considered are given in additional separate papers presented during this conference. The modeling considered current distributions over and within composite surfaces and the coupling of current and voltages to internal systems such as wire bundle cables and hydraulic and fuel tubes. The models were compared to each other and to measured data from low level swept continuous wave (LLCW) tests performed on two test fixtures. Other features of the codes such as run time, ease of use, computer requirements, availability of documentation and technical support, etc. are compared as well.

This paper introduces a comprehensive system of production planning for mass customization of non-rotational parts. The combined features are defined based on the concept of part families. The process parameters are associated with the feature parameters so that a rapid production planning can be achieved for product design changes. Setup planning is carried out based on both the best practice knowledge in industry and the analysis based generation of setups. Manufacturing resource, fixture design, and tolerance issues are considered in the system. The cycle time estimation and standard documentation are included in the system.

This paper introduces for the first time a fully connectorized passive optical star for use with plastic optical fiber that addresses all automotive application requirements. A unique mixing element is presented that offers linear expandability, uniformity of insertion loss, and packaging flexibility. The star is constructed of all plastic molded components to make it low cost and produceable in high volume and is single-ended to facilitate vehicle integration. The star is connectorized to facilitate assembly into the vehicle power and signal distribution system.

Experience tells us that one can develop a technically comfortable seat where the seat fits and supports the occupant. The pressure distribution is optimized and the seat and packaging are such that a good posture is attainable by many. The dynamic characteristics of the seat and the vehicle are technically good. Despite all this the customer is not satisfied. Despite it being a technically comfortable seat, it does meet the customers' expectations and/or priorities and thus the comfort provided is lacking. This paper seeks to explore that gap between the seat and the user by modeling comfort using techniques similar to those found in the social sciences where models often focus on user or individual behavior. The model is built upon but diverges from the Cobb Douglas consumer utility model found in economics. It is presented as theory and presents a very different perspective on comfort.

Critical speed yaw marks are commonly used in collision reconstruction to estimate vehicle speed. Research and laboratory testing have demonstrated that critical speed calculations can be used to accurately estimate vehicle speed. Thus, the principles supporting critical speed yaw analysis are fundamentally and theoretically valid and are not being challenged in this study. However, there are observed and documented limitations with respect to the appropriate application and execution of critical speed yaw analysis. This paper reviews the published research to-date and identifies limitations of critical speed yaw analysis. Examples of collision scenes are provided which quantify the inaccuracies associated with the misuse of critical speed yaw calculations. Areas for further research are identified and detailed.