Search Results

This procedure is applicable to modes from 500 and 13,000 Hz. The parameters measured with this procedure are defined as the damping factor, ξ for first nine vibration modes of the beam. The measurement will be done in free-free conditions and with temperature.

This document applies to shims only and will outline insulator design guidelines for improved manufacturability, cost and optimized product performance (Durability, bondability…)

This SAE Recommended Practice describes a laboratory test procedure for measuring the composite loss factor and bending stiffness properties of a system consisting of a damping material bonded to a vibrating bar which is excited at the center. The bar could be a steel, aluminum, glass, or other metal or composite bar that would be used in ground vehicles, marine products, and aircraft. The damping materials could be homogeneous, nonhomogeneous, a combination of homogeneous and nonhomogeneous, used in conjunction without or with an inelastic material (such as aluminum foil) in an extensional layer or a constrained layer configuration. The damping material could be a heat bondable material, adhesive backed sheet material, sprayable coating material, or other kinds of viscoelastic materials. The damping procedure discussed here provides means to measure damping over a range of frequencies and temperatures found applicable and useable for different transportation systems.

This SAE Recommended Practice establishes the test procedure, environment, and instrumentation to be used for measuring the exterior exhaust sound level for passenger cars, multipurpose vehicles, and light trucks under stationary conditions providing a continuous measure of exhaust system or simulated exhaust sound level over a range of engine speeds or simulated engine speeds. This document applies only to road vehicles equipped with an internal combustion engine or with an external sound system. The method is designed to meet the requirements of simplicity as far as they are consistent with reproducibility of results under the operating conditions of the vehicle.

This SAE Standard presents a test procedure for determining the airborne sound insulation performance of materials and composite layers of materials commonly found in mobility, industrial, and commercial products under conditions of representative size and sound incidence so as to allow better correlation with in-use sound insulator performance. The frequency range of interest is typically 100 to 10000 Hz 1/3-octave band center frequencies. This test method is designed for testing flat samples with uniform cross section, although in some applications the methodology can be extended to evaluate formed parts, pass-throughs, or other assemblies to determine their acoustical properties. For non-flat parts or assemblies where transmitted sound varies strongly across the test sample surface, a more appropriate methodology would be ASTM E90 (with a reverberant receiving chamber) or ASTM E2249 (intensity method with an anechoic or hemi-anechoic receiving chamber).

This SAE Standard establishes the minimum operational life cycles, environmental requirements, and sound level output for traffic horns (electric) on new automotive vehicles. Test equipment, environment, and procedures are specified.

This SAE Standard is equivalent to ISO Standard 362 - 1997 except for the differences detailed in Appendix A, and includes the modifications adopted by WP 29 in ECE R51 Revision 1 and EEC 92/97 and EEC 96/20. This document specifies an engineering method for measuring the noise emitted by accelerating highway vehicles of all types (except motorcycles) in intermediate gears with full utilization of the available engine power. The method is designed to meet the requirements of simplicity and reproducibility of results under realistic vehicle operating conditions. Measurements relate to operating conditions of the vehicle which give the highest noise level consistent with urban driving and which lead to reproducible noise emissions. Therefore, an acceleration test at full throttle from a stated engine or vehicle speed is specified. The test method calls for an acoustical environment which can only be obtained in an extensive open space.

This SAE Recommended Practice provides procedures and information to conduct vibration (impact) tests on lighting devices and their components as well as other safety equipment used on vehicles.

This SAE Recommended Practice describes a laboratory test procedure for measuring the thickness of various resilient insulating padding materials that are used in the automotive industry. Such padding materials may include synthetic or non-synthetic materials, fibrous or cellular materials, high loft or compressed materials, single layer homogeneous or multilayer products, low and high surface density products. Some of these samples may be deformable and elastic, high loft thermal and acoustical fibrous materials, as well. The test method described herein has been developed to establish a means of a uniform procedure for measuring the thickness of different types of samples not only for application to all ground vehicles, but also may be applicable to other situations or conditions. The test method is designed to measure the thickness of flat samples and not formed parts. This test method does not purport to address all of the safety concerns, if any, associated with its use.

The SAE J2521 procedure applies to high-frequency squeal noise occurrences for on-road passenger cars and light trucks below 4540 kg of GVWR. The procedure incorporates high-temperature and low-temperature test matrixes but does not fully account for the effects of the environment on brake squeal. For this test procedure, squeal occurs when the peak noise level is at least 70 dB(A) between 1.25 kHz and 16 kHz for tests using full suspension corners or full axle assemblies or between 2 kHz and 16 kHz for brakes not using a full suspension corner. Before using this recommended practice for chassis dynamometer testing, review in detail the specifics related to at least (a) instrumentation, including in-cabin microphones, (b) threshold levels for noise detection, (c) temperature control priority between the front and rear axles, (d) vehicle loading and load distribution, (e) cooling air and environmental conditioning, and (f) detailed nomenclature and labeling of channels and sensors.

This document describes standard test methods, analysis methods, and reporting methods for measuring the resonant modes of automotive disc brake rotors and drums for design/development and production verification of these components.

Procedures included within this specification are intended to cover performance testing at all phases of development, production, and field analysis of any USB cable assemblies and associated connections that constitute the electrical connection systems between the consumer peripheral interface and the USB computer source in road vehicle applications. These procedures are only applicable to the USB connector and the cable. Unless otherwise specified, all of the tests listed in this specification are for both consumer and nonconsumer interface connectors.

This SAE Standard describes a laboratory test procedure for measuring the vibration damping performance of a system consisting of a damping material bonded to a vibrating cantilevered steel bar. The bar is often called the Oberst bar (named after Dr. H. Oberst) and the test method is often called the Oberst bar test method. Materials for damping treatments may include homogeneous materials, nonhomogeneous materials, or a combination of homogeneous, nonhomogeneous, and/or inelastic (such as aluminum foil) materials. These materials are commonly installed in transportation systems such as ground vehicles, marine products, and aircraft to reduce vibration at resonance, and thus reduce the noise radiation from the vibrating surface. The test method described herein was developed to rank order materials for application on panels using general automotive steel but also may be applicable to other situations or conditions.

The following information covers accessory drive belt testing methods and includes test configurations, pulley diameters, power loads, and guidance for interpreting test data. Belt construction definitions are also documented. This information has been prepared from existing literature, including standards and data supplied by producers and users of V-ribbed belts.

This SAE Recommended Practice establishes the test procedure, environment, and instrumentation to be used for measuring the exterior exhaust sound level for passenger cars, multipurpose vehicles, and light trucks under stationary conditions providing a continuous measure of exhaust system sound level over a range of engine speeds. This document applies only to road vehicles equipped with an internal combustion engine. The method is designed to meet the requirements of simplicity as far as they are consistent with reproducibility of results under the operating conditions of the vehicle.

This SAE Standard covers minimum dimensional relationship for sheaves, drums, and wire rope for mobile, construction type lift cranes.

This SAE Recommended Practice provides supporting information for the emission and immunity measurement procedures defined in the SAE J1752 series of documents.

This SAE Recommended Practice describes a laboratory test procedure for measuring the random incidence sound absorption performance of a material or a part in a small size reverberation room by measuring decay rates. The absorption performance may include sound absorption coefficient of the test sample and or the amount of energy absorbed by the test sample. Materials for absorption treatments may include homogeneous materials, nonhomogeneous materials, or a combination of homogeneous, nonhomogeneous, and/or inelastic impervious materials. These materials are commonly installed in the mobility products and in the transportation systems such as ground vehicles, marine products, aircraft, and commercial industry (in industrial and consumer products) to reduce reverberant sound build-up and thus reduce the noise level in the environment by minimizing reflections off of hard surfaces.

This SAE Recommended Practice establishes the test procedures, performance requirements, and criteria necessary to evaluate minimum safety and reliability requirements of a children's snowmobile as identified in 1.2.

This SAE Recommended Practice establishes the test procedure, environment, and instrumentation for determining the maximum exterior sound level of highway motor trucks and truck tractors over 4540 kg gross vehicle weight rating (GVWR) with governed engines under stationary vehicle conditions. The basic procedure involves a full throttle engine acceleration and a closed throttle deceleration with the engine inertia as the load.