Search Results

This document outlines historical systems which have used the landing gear as a sensor or installation point for full aircraft weight and balance systems. A number of systems have been developed, installed, certified, and placed in service but few systems remain in regular use. The document will capture the history of these systems, reasons (where known) for their withdrawal from service, and lessons learned.

This report will document Runway Condition Monitoring systems that provide information intended to reduce or eliminate aircraft runway excursions or overruns that may occur as a result of poor runway conditions.

The scope of the test method is to provide stakeholders including fluid manufacturers, brake manufacturers, aircraft constructors, aircraft operators and airworthiness authorities with a relative assessment of the effect of deicing chemicals on carbon oxidation. This test is designed to assess the relative effects of runway deicing chemicals by measuring mass change of contaminated and bare carbon samples tested under the same conditions.

This document was requested by the FAA to provide a technical update of TSO-C26d to address Electric Brake Actuation, standardize with TSO-C135a and address any remaining concerns with the current technical requirements in AIR5381.

This SAE Aerospace Standard (AS) prescribes the Minimum Performance Standards (MPS) for environmental conditions that wheel, brake, and wheel and brake assemblies to be used on aircraft certificated under 14 CFR Parts 23, 25, 27, and 29. The environmental requirements in this document shall be used in conjunction with other MPS defined in Technical Standard Orders for the applicable equipment.

Publicize Aircraft Recommended Practice for Missionized Wear Testing on Wright Patterson’s Landing Gear Test Facility’s 168i dynamometer.

This document describes the assessment methods and physical requirements associated with the manual handling of carts and dollies, specific to material handling systems. All possible designs and applications could not be anticipated in creating these guidelines. Where there are questions of adherence to this document, such as use of an “off-the shelf” design, always consult the responsible Ergonomics Department. Force guidelines were primarily developed referencing the push/pull psychophysical Snook data contained in A Guide to Manual Materials Handling (second edition) by Mital, Nicholson and Ayoub (NY: Taylor & Francis, 1997). The force guidelines accommodate 75% of female capabilities and 99% of male capabilities. Factors that were included in the established guideline include: push / pull distances, vertical hand height, horizontal hand height, frequency and wheel / castor alignment and load rating. These factors were used to develop a conservative force guideline.

This SAE Aerospace Recommended Practice (ARP) establishes a procedure for disposition of aircraft wheels that have been involved in accidents/incidents or have been exposed to overheat conditions or overload conditions from loss of adjacent tire pressure (paired wheels) or wheel tie bolts.

This specification covers one type of cushion tread (semi-pneumatic) wheels for use on mobile ground support equipment.

This specification covers one type of cushion tread (semi-pneumatic) wheels for use on mobile ground support equipment.

This specification covers one type of cushion tread (semi-pneumatic) wheels for use on mobile ground support equipment.

For Engine Monitoring Systems to meet their potential for improved safety and reduced operation and support costs, significant attention must be focused on their reliability and validity throughout the life cycle. This AIR will provide program managers, designers, developers and customers a concise reference of the activities, approaches and considerations for the development and verification of a highly reliable engine monitoring system. When applying the guidelines of this AIR it should be noted that engine monitoring systems physically or functionally integrated with the engine control system and/or performing functions that affect engine safety or are used to effect continued operation or return to service decisions shall be subject to the Type Investigation of the product in which they'll be incorporated and have to show compliance with the applicable airworthiness requirements as defined by the responsible Aviation Authority.

The static mechanical stiffness properties of aircraft tires are fundamental to any computation of wheel and landing gear shimmy characteristics, and are important guides in anti-skid system and aircraft wheel design. While the mechanical stiffness properties of aircraft tires are frequency sensitive, the static or low frequency values are important because they are the ones most easily obtained by laboratory testing and are most commonly found in literature. The following recommended methods for measurement of such properties are believed to represent practices which will give reliable and repeatable measurements, either at one facility or among different facilities, using equipment which is commonly available in most tire testing installations.

This AS applies to the cavity design and the selection of O-rings for tubeless tire wheels.

This AS applies to the cavity design and the selection of O-rings for tubeless tire wheels.

This standard applies to the cavity design and the selection of O-rings for tubeless tire wheels.