Search Results

An extensive calibration study has been initiated to assess the predictive ability of CFD (Computational Fluid Dynamics) for the aerodynamic design of automotive shapes. Several codes are being checked against a set of detailed wind tunnel measurements on ten car-like shapes. The objective is to assess the ability of numerical analysis to predict the CD (drag coefficient) influence of the rear end configuration. The study also provides a significant base of information for investigating discrepancies between predicted and measured flow fields and for assessing new numerical techniques. This technical report compares STAR-CD predictions to the wind tunnel measurements. The initial results are quite encouraging. Calculated centerline pressure distributions on the front end, underbody and floor compare well for all ten shapes. Wake flow structures are in reasonable agreement for many of the configurations. Drag, lift, and pitching moment trends follow the experimental measurements.

Although concerns have been raised that the performance of activated carbon canisters will decrease when exposed to air at higher humidities, results of a recently conducted test program do not substantiate these concerns. The results show that the purge efficiency and the working capacity of canisters that are purged with air at 75 grains per pound of dry air (GPPDA) humidity are equal or greater than those obtained with 50 GPPDA humidity purging. The results have been submitted to the California Air Resources Board (ARB) for use in aligning their evaporative emission testing regulations with the regulations promulgated by the U. S. Environmental Protection Agency (EPA).

This report should not be looked upon as an end in itself, but rather as a thought provoker. It raises the question that there may be an additional dimension to race car aerodynamics other than just open roadway drag reduction, stability and handling performance. Some situations are seldom considered, nor even addressed, in public forums. Based upon wind tunnel test data, the authors show, at least for this one test setup, that significantly large changes in aerodynamic forces can be generated on a NASCAR stock car racer by its close proximity to the stationary retaining wall around a race track.

A four-stroke, spark-ignition engine is described that seeks to achieve high expansion ratio and low throttling losses at light load, whilst retaining good knock resistance at full load operation and without the need for expensive mechanical changes to the engine. The engine does, however, incorporate a second inlet (transfer) valve and associated transfer port linked to the intake port. The timing of the transfer valve is different from that of the main inlet valve. Load modulation is achieved by control of the gas outflow from the transfer port. A computer model of the engine is first validated against measured data from a conventional engine. Comparisons are made of incylinder pressure at part load conditions, total air flowrate through the engine and intake port air velocities as a function of crank angle position.

A subjective in-vehicle evaluation system is generally used to evaluate brake noise. This approach is quite dependent on analysis procedure, individual hearing abilities, individual tolerance level to the noise, the vehicle condition, road conditions and weather conditions. Due to the resultant subjective rating's dependence on these non-controllable factors, it was decided to develop an empirical laboratory technique using the brake dynamometer with sensitive noise measuring equipment to collect sufficient data on brake noise to allow engineers to study brake noise problems.

This paper presents a new transient passenger thermal comfort model. The model uses as inputs the vehicle environmental variables: air temperature, air velocity, relative humidity and mean radiant temperature all of which can vary as a function of time and space. The model also uses as inputs the clothing level and the initial physiological state of the body. The model then predicts as a function of time the physiological state of the body and an effective human thermal sensation response (e.g. cold, comfort, hot, etc.). The advantage of this model is that it can accurately predict the human thermal sensation response during transient vehicle warm-up and cooldown conditions. It also allows design engineers the ability to conduct parametric studies of climate control systems before hardware is available. Here we present the basis of the new thermal comfort model and its predictions for transient warm-up and cooldown conditions.

The crush performance of lightweight composite automotive structures varies significantly between static and dynamic test conditions. This paper discusses the development of a new dynamic testing facility that can be used to characterize crash performance at high loads and constant speed. Previous research results from the Energy Management Working Group (EMWG) of the Automotive Composites Consortium (ACC) showed that the static crush resistance of composite tubes can be significantly greater than dynamic crush results at speeds greater than 2 m/s. The new testing facility will provide the unique capability to crush structures at high loads in the intermediate velocity range. A novel machine control system was designed and projections of the machine performance indicate its compliance with the desired test tolerances. The test machine will be part of a national user facility at the Oak Ridge National Laboratory (ORNL) and will be available for use in the summer of 2002.

New vehicle control algorithms are needed to meet future emissions and fuel economy mandates that are quite likely to require a measurement of ambient specific humidity (SH). Current practice is to obtain the SH by measurement of relative humidity (RH), temperature and barometric pressure with physical sensors, and then to estimate the SH using a fit equation. In this paper a novel approach is described: a system of neural networks trained to estimate the SH using data that already exists on the vehicle bus. The neural network system, which is referred to as a virtual SH sensor, incorporates information from the global navigation satellite system such as longitude, latitude, time and date, and from the vehicle climate control system such as temperature and barometric pressure, and outputs an estimate of SH. The conclusion of this preliminary study is that neural networks have the potential of being used as a virtual sensor for estimating ambient and intake manifold's SH.

It is frequently useful to calculate the theoretical composition of the major components of vehicle exhaust. A software program has been written in Basic (or Quick Basic) which allows the convenient calculation of volume percents of CO, CO2, O2, H2, and H2O from fuel composition (H/C and O/C ratios), the water content (dew point) of the combustion air, and a chosen stoichiometry (air/fuel ratio). The program considers the Water Gas Shift reaction and the production of hydrogen under fuel rich conditions. The program is valid for both standard gasolines and oxygenated blends. Vehicle emissions data, collected to compare values calculated by the program with actual experimentally determined values from vehicle exhaust, show good agreement for measurements made at a series of air/fuel ratios ranging from lambda of 0.85-1.2.

Analytical methods for determining individual aldehyde, ketone, and alcohol emissions from gasoline-, methanol-, and variable-fueled vehicles are described. These methods were used in the Auto/Oil Air Quality Improvement Research Program to provide emission data for comparison of individual reformulated fuels, individual vehicles, and for air modeling studies. The emission samples are collected in impingers which contain either 2,4-dinitrophenylhydrazine solution for the aldehydes and ketones or deionized water for the alcohols. Subsequent analyses by liquid chromatography for the aldehydes and ketones and gas chromatography for the alcohols utilize autoinjectors and computerized data systems which permit high sample throughput with minimal operator intervention. The quality control procedures developed and interlaboratory comparisons conducted as part of this program are also described.

Most automobiles, at certain speeds with at least one window open, develop a pulsating pressure which is felt mainly through the ears and is objectionable to the occupants. While this “aerodynamic wind throb” is noticeable over a range of speeds, there is a fairly pronounced peak in the effect at one speed. This problem is studied analytically and experimentally. It is established that the car is a dynamic system consisting of a Helmholtz resonator excited by an edge tone. It is shown that the trouble can be corrected by changing the natural frequency, minimizing or eliminating the excitation, or increasing damping of the system.

Here we present an analytical model, written in general terms, which predicts the trajectory of a spherical particle/droplet placed in a uniform fluid stream. The model is compared to an experiment in which three millimeter diameter polypropolyene spheres (specific gravity = 0.91) are dropped in a uniform airstream (velocity varies from 0.9 to 3.8 m/s). Agreement between the two suggests the model incorporates all the important physics and thus should be useful as a design tool.

Future European air quality standards for light duty diesel vehicles will include stringent NOx emission regulations. In order to meet these regulations, a lean NOx catalyst system may be necessary. Since the catalytic removal of NOx is very difficult with the large concentration of oxygen present in diesel exhaust, a reductant is usually added to the exhaust to increase the NOx conversion. This paper describes a lean NOx catalyst system for a Transit light-duty truck which uses a reductant solution of urea in water. In this work, a microprocessor was used to vary the amount of the reductant injected depending on the operating conditions of a 2,5 L naturally aspirated HSDI engine. The NOx conversions were 60% and 80% on the current European driving cycle and the U.S. FTP cycles, respectively. Data on the emissions of HC, CO, NOx, particulate mass and composition, individual HC species, aldehydes, PAH and most HC species were evaluated.

Painting is the most difficult, the most costly, and the most polluting step in manufacturing vehicles. When low weathering performance paints are used, the results are dissatisfied customers, and huge warranty costs. It would obviously be wise to fully characterize the weathering performance of new coatings systems before they are used. Unfortunately this is not always practical. Coating formulations are changing rapidly in the States to comply with solvent emission regulations, the introduction of plastic substrates, and customer tastes. There is rarely enough time to wait ten years for outdoors exposure tests to reveal the "true" weathering performance of coatings before marketing vehicles. As a result, accelerated tests are often used to guide decisions. However, the results of such tests can be misleading because the harsh exposure conditions used can distort the chemistry of degradation.

Nowadays is a common sense the importance of the CAE usage in the modern automotive industry. The ability to predict the design behavior of a project represents a competitive advantage. However, some CAE models have become so complex and detailed that, in some cases, one just can not build up the model without a considerable amount of information. In that case simplified models play an important role in the design phase, especially in pre-program stages. This work intends to build an archetypal vehicle dynamics model able to predict the rollover resistance of a vehicle design. Through the study of a more complex model, carried out in Adams environment, it was possible to identify the key degrees of freedom to be considered in the simplified model along with important elements of the suspension which are also important design factors.

This paper quantifies typical United States in-vehicle cowl area particulate filter parameters such as temperature, humidity and environmental conditions. Secondly, United States and Germany particulate filter fleet results will be included to help quantify the effect of loading on electret nonwoven particulate filter fractional efficiency and demonstrate the amount and types of particulate matter captured. Finally the paper will address the low submicron fractional filter efficiency of a simulated production “wet and dry” plate-fin automotive evaporator core.

New high-temperature Mg alloys are being considered to replace 380 Al in transmission cases, wherein bolt-load retention, and creep, is of prime concern. One of these alloys is die cast AE42, which has much better creep properties than does AZ91D but is still not as creep resistant as 380 Al. It is thus important to investigate bolt-load retention and creep of AE42 as an initial step in assessing its suitability as a material for transmission housings. To that end, the bolt-load retention behavior of die-cast AE42, AZ91D and 380 Al have been examined using standard M10 bolts specially instrumented with stable high-temperature strain gages. The bolt-load retention test pieces were die cast in geometries approximating the flange and boss regions in typical bolted joints. Bolt-load retention properties were examined as a function of time (at least 100 hours), temperature (150 and 175 °C) and initial bolt preload (14 to 34 kN).

The ISO TC22/SWG2 - Brake Lining Committee established a task force to determine and analyze root causes for variability during dynamometer brake performance testing. SAE paper 2010-01-1697 “Brake Dynamometer Test Variability - Analysis of Root Causes” [1] presents the findings from the phases 1 and 2 of the “Test Variability Project.” The task force was created to address the issue of test variability and to establish possible ways to improve test-to-test and lab-to-lab correlation. This paper presents the findings from phase 3 of this effort-description of factors influencing test variability based on DOE study. This phase concentrated on both qualitative and quantitative description of the factors influencing friction coefficient measurements during dynamometer testing.

Flow fields generated during the intake stroke of a 4-stroke I.C. engine are studied experimentally using water analog simulation. The fluid is seeded by small flow tracer particles and imaged by two digital cameras at BDC. Using a 3-D Particle Tracking Velocimetry technique recently developed, the 3-D motion of these flow tracers is determined in a completely automated way using sophisticated image processing and PTV algorithms. The resulting 3-D velocity fields are ensemble averaged over a large number of successive cycles to determine the mean characteristics of the flow field as well as to estimate the turbulent fluctuations. This novel technique was applied to three different cylinder head configurations. Each configuration was run for conditions simulating idle operation two different ways: first with both inlet ports open and second with only the primary port open.

In premixed turbulent combustion models, two mechanisms have been used to explain the increase in the flame speed due to the turbulence. The newer explanation considers the full range of turbulence scales which wrinkle the flame front so as to increase the flame front area and, thus, the flame propagation speed. The fractal combustion model is an example of this concept. The older mechanism assumes that turbulence enables the penetration of unburned mixtures across the flame front via entrainment into the burned mixture zone. The entrainment combustion or eddy burning model is an example of this mechanism. The results of experimental studies of combustion regimes and the flame structures in SI engines has confirmed that most combustion takes place at the wrinkled flame front with additional combustion taking place in the form of flame fingers or peninsulas.