Search Results

An experimental study of particulate matter and volatile organic compounds (VOCs) emissions was conducted on a direct injection gasoline (DIG) engine and a port fuel injection (PFI) engine which both were produced by Chinese original equipment manufacturers (OEMs) to investigate the impact of fuel properties from Chinese market on particulate and VOCs emissions from modern gasoline vehicles. The study in this paper is just the first step of the work which is to investigate the impact of gasoline fuel properties and light duty vehicle technologies on the primary and secondary emissions, which are the sources of particulate matter 2.5 (PM2.5) in the atmosphere in China. It is expected through the whole work to provide some suggestions and guidelines on how to improve air quality and mediate severe haze pollution in China through fuel quality control and vehicle technology advances.

The design and optimization of a modern spray-guided gasoline direct injection engine require a thorough understanding of the fuel spray characteristics and atomization process. The fuel spray Computational Fluid Dynamics (CFD) modeling technology can be an effective means to study and predict spray characteristics, and as a consequence, to drastically reduce experimental work during the engine development process. For this reason, an accurate numerical simulation of the spray evolution process is imperative. Different models based on aerodynamically-induced breakup mechanism have been implemented to simulate spray atomization process in earlier studies, and the effect of turbulence from the injector nozzle is recently being concerned increasingly by engine researchers. In this study, a turbulence-induced primary breakup model coupled with aerodynamic instability is developed.

Combustion behaviour and emissions characteristics of different blending ratios of diesel and gasoline fuels (Dieseline) were investigated in a light-duty 4-cylinder compression-ignition (CI) engine operating on partially premixed compression ignition (PPCI) mode. Experiments show that increasing volatility and reducing cetane number of fuels can help promote PPCI and consequently reduce particulate matter (PM) emissions while oxides of nitrogen (NOx) emissions reduction depends on the engine load. Three different blends, 0% (G0), 20% (G20) and 50% (G50) of gasoline mixed with diesel by volume, were studied and results were compared to the diesel-baseline with the same combustion phasing for all experiments. Engine speed was fixed at 1800rpm, while the engine load was varied from 1.38 to 7.85 bar BMEP with the exhaust gas recirculation (EGR) application.

An experimental study of particulate matter (PM) emission was conducted on four cars from Chinese market. Three cars were powered by gasoline direct injection (GDI) engines and one car was powered by a port fuel injection (PFI) engine. Particulate mass, number and size distribution were measured based on a chassis dynamometer over new European driving cycle (NEDC). The particulate emission behaviors during cold start and hot start NEDCs were compared to understand how the running conditions influence particulate emission. Three kinds of gasoline with RON 91.9, 94.0 and 97.4 were tested to find the impact of RON on particulate emission. Because of time and facilities constraints, only one cold/hot start NEDC was conducted for every vehicle fueled with every fuel. The test results showed that more particles were emitted during cold start condition (first 200s in NEDC). Compared with cold start NEDC, the particulate mass and number of hot start NEDC decreased by a wide margin.

This paper studied the knock combustion process in gasoline HCCI engines. The complex chemical kinetics was implemented into the three-dimensional CFD code with LES (Large eddy simulation) to study the origin of the knock phenomena in HCCI combustion process. The model was validated using the experimental data from the cylinder pressure measurement. 3D-CFD with LES method gives detailed turbulence, species, temperature and pressure distribution during the gasoline HCCI combustion process. The simulation results indicate that HCCI engine knock originates from the random multipoint auto-ignition in the combustion chamber due to the slight inhomogeneity. It is induced by the significantly different heat release rate of high temperature oxidation (HTO) and low temperature oxidation (LTO) and their interactions.

Fuel spray atomization process is known to play a key role in affecting mixture formation, combustion efficiency and soot emissions in direct injection engines. The fuel spray Computational Fluid Dynamics (CFD) modeling technology can be an effective means to study and predict spray characteristics such as penetration, droplet size and droplet velocity, and as a consequence, to drastically reduce experimental work during the engine development process. For this reason, an accurate numerical simulation of the spray evolution process is imperative. Different approaches and various models based on aerodynamically induced breakup mechanism have been implemented to simulate spray atomization process in earlier studies, and the effects of turbulence and cavitation from the injector nozzle is recently being concerned increasingly by engine researchers. In this study, an enhanced turbulence and cavitation induced primary breakup model combining aerodynamic breakup mechanism is developed.