Search Results

From hydrogen-fueled buses to AI-driven advancements and cybersecurity, this book offers an unparalleled glimpse into the future of transit. Navigate the complexities of transit planning in a post-COVID world, where innovative solutions are essential to tackle infrastructure challenges and workforce shortages.

It is essential to note that cybersecurity threats not only arise from inherent protocol defects but also consider software implementation vulnerabilities.

UNECE R155 explicitly references ISO/SAE 21434 and mandates a certified cybersecurity management system (CSMS) as a prerequisite for automotive manufacturers to achieve vehicle type approval and sell new vehicle types. ...However, the gap in the CSMS framework is a lack in a standardized system that provides guidance and common criteria for automakers to measure a vehicle’s level of compliance and compute a publicly accepted cybersecurity rating. To help establish increased consumer confidence, OEMs and smart mobility stakeholders could take additional proactive steps to ensure the safety and security of their products. ...This paper addresses the above requirement and discusses the cybersecurity rating framework (CSRF) that could establish a framework for rating vehicle cybersecurity by standardizing the measurement criteria, parameter vectors, process, and tools.

This paper gives a definition of the SDV concept, provides views from different aspects, discusses the progress in vehicle E/E architecture, especially zone-based architecture with centralized computation, and various technologies including High-Performance Computing (HPC) platform, standardized vehicle software architecture, advanced onboard communication, Over-The-Air (OTA) update, and cybersecurity etc. that collectively enable the realization of SDV.

Abstract The United Nation Economic Commission for Europe (UNECE) Regulation 155—Cybersecurity and Cybersecurity Management System (UN R155) mandates the development of cybersecurity management systems (CSMS) as part of a vehicle’s lifecycle. ...Due to the focus of R155 and its suggested implementation guideline, ISO/SAE 21434:2021—Road Vehicle Cybersecurity Engineering, mainly centering on the alignment of cybersecurity risk management to the vehicle development lifecycle, there is a gap in knowledge of proscribed activities for validation and verification testing. ...An inherent component of the CSMS is cybersecurity risk management and assessment. Validation and verification testing is a key activity for measuring the effectiveness of risk management, and it is mandated by UN R155 for type approval.

Abstract Connected autonomous vehicles that employ internet connectivity are technologically complex, which makes them vulnerable to cyberattacks. Many cybersecurity researchers, white hat hackers, and black hat hackers have discovered numerous exploitable vulnerabilities in connected vehicles. ...This study expanded the technology acceptance model (TAM) to include cybersecurity and level of trust as determinants of technology acceptance. This study surveyed a diverse sample of 209 licensed US drivers over 18 years old.

Headliners from Las Vegas Big reveals abounded at the triennial CONEXPO trade show. Following are some of the most notable unveilings from the desert. Cat doubles down on diesel with new C13D platform Deere pursues electric construction machines and charging infrastructure JCB debuts clean-sheet hydrogen combustion engine Volvo CE unveils electric asphalt compactor, announces NA arrival of L350H loader Honda reveals next-gen Autonomous Work Vehicle Deere 3D-prints fuel valves for tractors HP's binder jetting technology and GKN's manufacturing expertise helped John Deere realize its first 3D-printed metal part for mass production. Returning to the SAE presidency for 2023 Setting a "prudently aggressive" mindset in advancing SAE's goals in the mobility ecosystem.

Access control enforces security policies for controlling critical resources. For V2X (Vehicle to Everything) autonomous military vehicle fleets, network middleware systems such as ROS (Robotic Operating System) expose system resources through networked publisher/subscriber and client/server paradigms. Without proper access control, these systems are vulnerable to attacks from compromised network nodes, which may perform data poisoning attacks, flood packets on a network, or attempt to gain lateral control of other resources. Access control for robotic middleware systems has been investigated in both ROS1 and ROS2. Still, these implementations do not have mechanisms for evaluating a policy's consistency and completeness or writing expressive policies for distributed fleets. We explore an RBAC (Role-Based Access Control) mechanism layered onto ROS environments that uses local permission caches with precomputed truth tables for fast policy evaluation.

Automotive system functionalities spread over a wide range of sub-domains ranging from non-driving related components to complex autonomous driving related components. The requirements to design and develop these components span across software, hardware, firmware, etc. elements. The successful development of these components to achieve the needs from the stockholders requires accurate understanding and traceability of the requirements of these component systems. The high-level customer requirements transformation into low level granularity requires an efficient requirement engineer. The manual understanding of the customer requirements from the requirement documents are influenced by the context and the knowledge gap of the requirement engineer in understanding and transforming the requirements.

This exercise confirms the necessity of a more restrictive cybersecurity posture in automotive peripherals with access to critical systems, in particular VDAs, and especially when such peripherals present a wireless interface.

But unfortunately, automotive cybersecurity researchers hardly produce a comprehensive detection method due to the confidential nature of Controller Area Network (CAN) DBC format files, which is a standard long maintained by car manufacturers.

The new generation vehicles these days are managed by networked controllers. A large portion of the networks is planned with more security which has recently roused researchers to exhibit various attacks against the system. This paper talks about the liabilities of the Controller Area Network (CAN) inside In-vehicle communication protocol and a few potentials that could take due advantage of it. Moreover, this paper presents a few security measures proposed in the present examination status to defeat the attacks. In any case, the fundamental objective of this paper is to feature a comprehensive methodology known as Intrusion Detection System (IDS), which has been a significant device in getting network data in systems over many years. To the best of our insight, there is no recorded writing on a through outline of IDS execution explicitly in the CAN transport network system.

Classic vehicle production had limitations in bringing the driving commands to the actuators for vehicle motion (engine, steering and braking). Steering columns, hydraulic tubes or steel cables needed to be placed between the driver and actuator. Change began with the introduction of e-gas systems. Mechanical cables were replaced by thin, electric signal wires. The technical solutions and legal standardizations for addressing the steering and braking systems, were not defined at this time. Today, OEMs are starting E/E-Architecture transformations for manifold reasons and now have the chance to remove the long hydraulic tubes for braking and the solid metal columns used for steering. X-by-wire is the way forward and allows for higher Autonomous Driving (AD) levels for automated driving vehicles. This offers new opportunities to design the vehicle in-cabin space. This paper will start with the introduction of x-by-wire technologies.

The separation of cybersecurity considerations in RMTO is barely considered, as so far, most available research and activities are mainly focused on AV. ...The main focus of this paper is addressing RMTO cybersecurity utilising an adaptable security-by-design approach, although security-by-design is still in the infant state within automotive cybersecurity. ...The main focus of this paper is addressing RMTO cybersecurity utilising an adaptable security-by-design approach, although security-by-design is still in the infant state within automotive cybersecurity. An adaptable security-by-design approach for RMTO covers Security Engineering Life-cycle, Logical Security Layered Concept, and Security Architecture.

Using a wireless medium for tractor-trailer communication will bring new cybersecurity challenges and requirements which requires new development and lifecycle considerations.

There continues to be massive advancements in modern connected vehicles and with these advancements, connectivity continues to rapidly become more integral to the way these vehicles are designed and operated. Vehicle connectivity was originally introduced for the purpose of providing software updates to the vehicle’s main system software, and we have seen the adoption of Over The Air updates (OTA) become mainstream with most OEMs. The exploitation of this connectivity is far more reaching than just basic software updates. In the latest vehicles it is possible to update software not just on the main vehicle systems, but to potentially update embedded software in all smart ECUs within the vehicle. Only using the connectivity to push data to the vehicle is not making full use of the potential of this increased connectivity. Being able to collect vehicle data for offline analysis and processing also brings huge benefits to the use of this technology.

CAN bus network proved to be efficient and dynamic for small compact cars as well as heavy-duty vehicles (HDV). However, HDVs are more susceptible to malicious attacks due to lack of security in their intra-vehicle communication protocols. SAE proposed a new standard named J1939-91C for CAN-FD networks which provides methods for establishing trust and securing mutual messages with optional encryption. J1939-91C ensures message authenticity, integrity, and confidentiality by implementing complex cryptographic operations including hash functions and random key generation. In this paper, the three main phases of J1939-91C, i.e., Network Formation, Rekeying, and Message Exchange, are simulated and tested on Electronic Control Units (ECUs) supporting CAN-FD network. Numerous test vectors were generated and validated to support SAE J1939-91C. The mentioned vectors were produced by simulating different encryption and hashing algorithms with variable message and key lengths.

The lack of inherent security controls makes traditional Controller Area Network (CAN) buses vulnerable to Machine-In-The-Middle (MitM) cybersecurity attacks. Conventional vehicular MitM attacks involve tampering with the hardware to directly manipulate CAN bus traffic.

SMSOLUTIONS0123 represents the work of a team of policy and technical leaders from over a dozen forward-leaning organizations in the ground vehicle industry and government. When asked where Sustainable Mobility Solutions could best apply the capabilities SAE has developed over a century, the SMS group responded without hesitation: address EV charging system failure. The group determined to aggregate charging session data with the view to create a consistent data dictionary and analysis practice. Adopting agile work practices, it studied these data, vetting and iterating its solution with the objective of producing a technical report in approximately half the time required in normal standardization. The resulting document, EV Charging Infrastructure: Charging System Performance Reporting, is informing work by the U.S. Department of Energy and Departments of Energy and Transportation Joint Office, as well as OEMs and suppliers.