Search Results

This paper presents experimental results of a 10.6L, three-cylinder opposed-piston (OP) operating on diesel fuel designed for heavy duty (Class 8) operation. The paper will describe the engine configuration and calibration of both catalyst light-off and high efficiency modes. Analysis based on measured results show the engine can comply with all 2027 California Air Resourced Board (CARB) and Environmental Protection Agency (EPA) requirements for CO2 and criteria emissions. Due to the ability of the OP Engine to combine low oxides of nitrogen (NOX) flux with high exhaust enthalpy for early catalyst light off, the engine can meet all 2027 CARB and EPA NOX standards with a current, state of the art conventional underfloor aftertreatment system. No additional emissions control technology is required.

The 2010 emission standards for heavy-duty diesel engines in the U.S. have established a limit for oxides of nitrogen (NOx) emissions of 0.20 g/bhp-hr., a 90% reduction from the previous emission standards. However, it has been projected that even when the entire on-road fleet of heavy-duty vehicles operating in California is compliant with the 2010 emission standards, the upcoming National Ambient Air Quality Standards (NAAQS) requirement for ambient particulate matter and ozone will not be achieved in California without further significant reductions in NOx emissions from the heavy-duty vehicle fleet. Given this, there is potential of further reduction in NOx emissions limit standards for heavy duty engines in the US. Recently there have been extensive studies and publications focusing on ultra-low NOx after treatment technologies that help achieve up to 0.02g/bhp-hr. at tailpipe [1].

Historically, the opposed-piston, two-stroke (OP2S) diesel engine set combined records for fuel efficiency and power density that have yet to be met by any other engine type. However, with modern emissions standards, wide-spread development of this engine for on-highway use stopped. At Achates Power, state-of-the-art analytical tools and engineering methods have produced an OP2S engine that, when compared to a leading medium-duty engine, has demonstrated a 21% fuel efficiency gain and engine-out emissions levels meeting U.S. EPA10 with conventional after-treatment. Among the presentation topics covered are thermodynamic efficiency, demonstrated engine results, cost and weight advantages, and overcoming two-stroke engine challenges. Presenter David Johnson, Achates Power Inc.

Conventional diesel fuel has been in the market for decades and used successfully to run diesel engines of all sizes in many applications. In order to reduce emissions and to foster energy source diversity, new fuels such as alternative and renewable, as well as new fuel formulations have entered the market. These include biodiesel, gas-to-liquid, and alternative formulations by states such as California. Performance variations in fuel economy, emissions, and compatibility for these fuels have been evaluated and debated. In some cases contradictory views have surfaced. “Sustainable”, “Renewable”, and “Clean” designations have been interchanged. Adding to the confusion, results from one fuel in one type of engine such as an older heavy-duty engine, is at times compared to that of another fuel in another type such as a modern light-duty engine. This study was an attempt to compare the performance of several fuels in identical environments, using the same engine, for direct comparison.

Conventional diesel fuel has been in the market for decades and used successfully to run diesel engines of all sizes in many applications. In order to reduce emissions and to foster energy source diversity, new fuels such as alternative and renewable, as well as new fuel formulations have entered the market. These include biodiesel, gas-to-liquid, and alternative formulations by states such as California. Performance variations in fuel economy, emissions, and compatibility for these fuels have been evaluated and debated. In some cases contradictory views have surfaced. “Sustainable”, “Renewable”, and “Clean” designations have been interchanged. Adding to the confusion, results from one fuel in one type of engine such as an older heavy-duty engine, is at times compared to that of another type such as a modern light-duty. This study was an attempt to compare the performance of several fuels in an identical environment, using the same engine, for direct comparison.

Over the past several years, economic pressures have driven fleets to substantially increase their maintenance intervals. To meet this challenge, both the Original Equipment Manufacturers (OEMs) and the lubricant suppliers have developed new and better products to give fleet users the benefits of extended service intervals, while at the same time maintaining equipment life and providing the potential for reduced operating costs. Through the selection of proper lubricants, fleets can now minimize their total operating costs with products that meet the OEM extended service specifications, have demonstrated equipment durability, and are formulated using base oil and additive components to minimize the cost of the lubricant. This paper will examine the options available for formulating extended drain transmission and axle lubricants. It will explore the selection of the lubricant base oil as well as the additive system.

Experiments were performed to measure the number-weighted particle size distributions emitted from a gasoline direct injection (GDI) engine. Measurements were made on a late model vehicle equipped with a direct injection spark ignition engine. The vehicle was placed on a chassis dynamometer, which was used to load the engine to road load at five different vehicle speeds ranging from 15 - 100 km/hr. Dilution of the exhaust aerosol was carried out using a two-stage dilution system in which the first stage dilution occurs as a free jet. Particle size distributions were measured using a TSI 3934 scanning mobility particle sizer. Generally speaking, the presence of the additives did not have a strong, consistent influence on the particle emissions from this engine. The polyether amine demonstrated a reduction in particle number concentration as compared to unadditized base fuel.

FTP-UDDS (urban dynamometer driving schedule) exhaust particulate matter (PM) emission rates were determined for 361 light-duty gasoline (LDGV) and 49 diesel passenger vehicles ranging in model year (MY) from 1965 to 1997. LDGVs were recruited into four MY categories. In addition, special effort was made to recruit LDGVs with visible smoke emissions, since these vehicles may be significant contributors to the mobile source PM emission inventory. Both light and heavy-duty diesels where included in the passenger diesel test fleet, which was insufficient in size to separate into the same MY categories as the LDGVs. Vehicles were tested as-received in three areas: Denver, Colorado; San Antonio, Texas; and the South Coast Air Quality Management District, California. The average PM emission rates were 3.3, 79.9, 384 and 558 mg/mi for 1991-97 MY LDGVs, pre-1981 LDGVs, smoking LDGVs and the diesel vehicles, respectively.

In order to meet EPA's emission requirements for 1999 diesel engines, soot levels in the crankcase oil will increase significantly due to retarded timing to lower NOx. This study uses the Cummins M11 engine at soot levels up to 9% in the crankcase oil to demonstrate how oils can be formulated to prevent valve train wear, extend filter life, and maintain oil pumpability. The study includes the oil formulation development and the evaluation of API CG-4/SJ oils at 4.5% soot and API CH-4/SJ oils at 9% soot. In addition it includes X-Ray Photoelectron Spectroscopy (XPS) for surface film analysis and Surface Optical Profilometry and Scanning Electron Microscopy (SEM) of the valve train valve-bridges and rocker pads to determine the mechanism of failure. The oil's low temperature rheology as it affects oil pumpability is defined by Mini Rotary Viscometer (MRV TP-1), Scanning Brookfield Test (SBT), and Cold Cranking Simulator (CCS).