Search Results

This project was undertaken with an objective to develop methodology by formulating set of procedures that would help in achieving the end goal. Once methodology is established, it paves way to optimize the end results more effectively which results in reduced lead time during product development. Methodology can either be based on pure experimental investigations or by simulations. Combination of mathematical and empirical approach is inherently followed in simulations, which helps in reducing the testing time and overall cost. Commercial vehicles (CV) have seen paradigm shift in the fuel consumption (FC) certification approaches, with an intention to align with 2016 Paris climate agreement. Use of simulation tool like VECTO for commercial vehicle FC certification has gained momentum in Europe. Overall experience gained in commercial vehicle FC simulation has motivated us to leverage the learnings for off-road applications like agricultural tractors.

In India, B7 (a biodiesel mix of 7% by volume in diesel) has been approved for use in diesel engines. Due to the depletion of fossil fuel supplies and tight pollution requirements, alternative diesel fuel has become critical. However, given the properties of diesel, no direct renewable alternative fuel can totally replace diesel. As a result, one of the solutions may be to replace part of the diesel with ethanol. In this inquisition, the impact of various diesel-ethanol blends, counting ED7.7, ED10, ED15 and ED20, were examined on two in-use multi-cylinder engines complying to different emission norms. The two engines under consideration complies with CPCB-I and CPCB-II, which is an Indian legal requirement for stationary Genset engines. For both engines, a 5-mode steady-state test cycle was considered. For each mode, the engine’s performance characteristics, including power, torque, and BSFC, were tested and described.

Currently, on-road transport contributes nearly 12% of India’s total energy related carbon dioxide (CO2) emissions that are expected to be doubled by 2040. Following the global trends of increasingly stringent greenhouse gas emissions (GHG) and criteria emissions, India will likely impose equivalent Bharat Stage (BS) regulations mandating simultaneous reduction in CO2 emissions and nearly 90% lower nitrogen oxides (NOx) from the current BS-VI levels. Consequently, Indian automakers would likely face tremendous challenges in meeting such emission reduction requirements while balancing performance and the total cost of ownership (TCO) trade-offs. Therefore, it is conceivable that cost-effective system improvements for the existing internal combustion engine (ICE) powertrains would be of high strategic importance for the automakers.

Methanol fuel has attracted global attention from engine researchers since the crude oil crisis and the rise in crude oil prices in the recent years. As it is one of the possible alcoholic fuels after ethanol in an automotive application that can reduce dependence on crude oil. India has also initiated research studies on methanol since the 1980s. NITI Aayog is encouraging the use of methanol as an automotive fuel for transport sector. This desktop study includes the potentiality of methanol as an automotive fuel and the methanol roadmap for India as a biofuel in the conventional gasoline application. It has been seen that Methanol has the potential to be used as a fuel in automobiles to replace gasoline or crude oil-based fuels in terms of engine performance. According to a study, India’s methanol promotion measures will encourage more enterprises to invest in the research and construction of methanol producing plants and development of methanol-fueled engines.

Bharat Stage VI emission norms were implemented in India in two stages: Stage I from April 1, 2020, and Stage II from April 1, 2023. For M & N category vehicles, the RDE test along with other applicable certification tests is mandatory for obtaining a BSVI compliance certificate during stages I and II. The RDE test is conducted on roads under real driving conditions, unlike the Type-I test, which uses a predefined cycle on the chassis dynamometer, during which the ambient temperature and other environmental conditions are controlled in a narrow range. During BSVI Stage I for the RDE test, there was no limit for any pollutant. Therefore, it is considered as the RDE monitoring stage, and from BS-VI Stage II, limits are enforced on a few pollutants (NOX and PN) as notified in notification GSR 226(E) dated March 27, 2023. Therefore, it is considered the RDE compliance stage.

The Light commercial vehicle (LCV) is primarily used for the last mile delivery and it hold the volume share of around 61% in the commercial vehicle segment. The last mile delivery services have seen a massive surge after the CoVID 19 pandemic resulting is the increase sale of LCV in last few years and is expected to grow further by 8-11% in the coming years. However, city logistic is also responsible for most pollution and noise in the city. Hence, policymakers are aiming to reduce carbon footprint by promoting the use of Electric vehicle by providing incentive to automakers though schemes like FAME I and FAME II. In order to effectively reduce the carbon footprint within city it is important to increase the use of new electric vehicle and convert the old polluting vehicles to electric. Hence, a retro fitment solution for converting used LCV to electric can help in reducing emission as well as noise pollution. Later the same solution can be offered as OE fitment solution.

Researchers are under pressure to investigate and discover ways to improve the efficacy and reduce emissions from ICE due to the depletion of energy resources and the growing concern over global warming. Hydrogen is viewed as a promising fuel and has been investigated as a potential fuel in combustion because to several desirable qualities like carbon-less content and strong flammability limitations. When equated to other alternative fuels like LPG, CNG, LNG, etc., hydrogen has inimitable qualities because it lacks carbon, making it one of the promising alternatives fuels. In order to achieve zero CO2 emissions for traffic applications in the near future, hydrogen being an automotive fuel in ICE is a solution. The ICE powered by hydrogen is prepared for that. The actual drawbacks of using hydrogen in ICE generally are manufacturing, storage, and development of the requisite infrastructure. Hydrogen can be produced in its many forms.

The Indian automotive industry is striving towards more safe and durable vehicles. A need was felt to study the effect of changes in axle static loads on fatigue life of the axle components. Also, there was a need to develop generic test method, as there are no test standards or generic methods available in public domain for fatigue testing of commercial vehicle axles. The study was carried out to check direct effect of change in axle loads on various connections on axle, effect of suspension configuration and force distribution, Vehicle dynamics, etc. In this paper, an India specific generic load spectra was evaluated for accelerated laboratory validation. Paper discusses the methodology as; study of heavy commercial vehicle systems, road load data collection on identified test vehicles w.r.t. test matrix finalized, India specific test loads and load spectra development, normalization of axle load spectra w.r.t to static axle weights and arriving at test guidelines.

The windscreen wiping system is mandatory requirement for automotive vehicle as per Central motor vehicle rules (CMVR). The main scope of the standard is to ensure vision zones to be wiped by wiping system to ensure maximum field of vision to the driver. The evaluation of vision zones as per IS 15802:2008 is generally determined by virtual simulation by OEMs. The limitation of virtual simulation is due to actual tolerances in vehicle, due to seat fitment, ergonomic dimensions, seat cushioning effect and wiper non-effective operation which are not taken into consideration very well off. The testing methodology described in the paper is an in-house developed test method based on SAE recommended practices. With the help of 3D H-point machine and a laser based ‘Theodolite’ equipped with horizontal and vertical angle projections from single pivot point is used to develop various vision zones on an actual vehicle windscreen as per technical data.

Engine mount is an integral part of any Internal Combustion engine. It is the medium which isolates the vibrations coming from engine being transferred to the chassis or body. Engine or power plant is the main source of unbalanced vibrations. The major role of an engine mount is to reduce those vibration levels, improve ride comfort and increase the life of an engine and its parts [1]. This work determines the Test methodology development for passenger car engine mounts in the Laboratory by using Multi-axial environment [2]. This explains the details of truly Multi-axial test rig development, Drive file creation and the Durability Testing with the maintained vehicle conditions by simulating field conditions in the laboratory. The Multi-axial test rig developed with incorporation of vehicle’s both Front Drive shafts torques and One Propeller shaft which simulates the Front wheel drives and the rear prop shaft torque.

The Indian market for battery-powered electric vehicles (xEV) is growing exponentially in the coming years, fueled by tumbling lithium-ion battery prices and favorable government policies. Lithium-ion battery is leading in clean mobility ecosystem for electric vehicles. LiBs efficient and safe performance for tropical climatic conditions is one of the primary requirements for xEV to succeed in India. The performance of LiBs, however, is impacted due to ambient temperature as well as the heat generated within cell due to the load cycle electrochemical reaction. The acceptable operating temperature region for LiBs normally is between 20 °C to 45 °C and anything outside of this region will lead to degradation of performance and irreversible damages. Therefore, understanding the thermal behavior is very crucial for an efficient battery thermal management.

Particulate matter is one of the major pollutant responsible for deteriorating air quality, particularly in urban centers. Information on contributing sources with the share from different sources is a first and one of the important steps in controlling pollution. Diverse sources, anthropogenic as well as natural, like industries, transport, domestic burning, construction, wind-blown dust, road dust contribute to particulate matter pollution. Receptor modeling is a scientific method which is utilized for assessment of the contribution of various sources based on chemical characteristics of particulate matter sources and ambient air particulate matter. Representative data of fractions of various chemical species in the particulate matter from the different sources i.e. source fingerprint is an essential input for the receptor modeling approach.

Last decade has been era of environmental awareness. Various programs have launched for making devices and appliances eco-friendly. This initiative has lead automobile industry toward hybridization and now total electrification of vehicles. As electric motor is being added to automobile as a prime mover, due to high frequency vibrations along with higher torque electric motor needs to be isolated properly & carefully as this vibration can damage other automobile parts. Dynamic response of electric motor is different from response of IC engines, so use of engine mounting design method may not be suitable for designing mounting system for electric motor. First, both 4- point and 3- point mounting system are considered for analytical and experimental investigation of force and displacement transmissibility. Position and orientation of elastomeric mounts plays important role in design of mounting system for electric motor.

NVH has gained importance in the field of earth moving equipment due to the demand of quieter machines and stringent in-cab as well as exterior noise emission norms. Several parts of the world have adopted strict legislation on noise emission by earth moving equipment, but many countries have not adopted any regulations till date. The aim of this study is to help governing bodies as well as machine manufacturers in adopting simple yet accurate testing method for compactor machine. The study consists of directivity analysis, noise source identification, noise source ranking and 4-point microphone position sound power evaluation method applied to compactors with wide range of engine power ratings. All the tests in 4-point method and directivity analysis were performed under stationary as well as dynamic conditions.

The Electric Vehicles (EV) or Hybrid Electric Vehicle (HEV) has a bunch of electrical/electronic components and its operation give rise to complicated EMI/EMC issues. The Power Electronics Module (PEM), comprising of DC-DC convertor/invertor and Battery Management Unit (BMU), is driving the motor to propel the vehicle. “Battery Pack Module” powers these units through cables. The fast switching of these circuit elements present in the system leads to noise propagation through the cables. These noise signals give rise to various Electromagnetic (EM) related issues in the cable harness of vehicle. It is essential that these cables should not interfere with other electronic components and also does not get effected by external EM disturbances.

Design of real time active controls for structural dynamics problems requires a very precise mathematical model, to closely determine the system dynamic behavior, under virtual simulation. The finite element models can somehow be used as a mathematical model but due to complex shape/structure of the component, the size of discrete models resulting from finite element analysis is usually very large, causing the virtual simulation to be extremely computationally intensive and time consuming, also the boundary conditions applied are not very scalable, making the system deviate from its real dynamic behavior. Thus, this paper deals with the design of a Model Order Reduction technique, using orthogonal decomposition of system matrices, which can be used for creating accurate low-order dynamic model with scalable boundary conditions.

The automotive and related industries are concentrating their efforts on improving comfort by lowering engine, wind, and road noise and vibrations. However, as background noise levels decrease, the squeaks and rattles (S&R) generated by the vehicle's many components become more noticeable and distracting. As a result of the absence of a dominant noise source from a traditional petrol/diesel car, (S&R) noise becomes more dominant than other types of noise in electric vehicles. In this paper, we propose a novel simulation technique for developing a systematic approach to identifying and solving (S&R) problems in vehicle components/sub-assemblies during the primary stage of product development cycle, thus reducing the overall product development time. This paper will present a novel approach to comprehending various methods and Design of Experiments (DOE) techniques used to determine the root cause of (S&R) problems and to solve those using numerical methods.

Bharat Stage VI (BS VI) emission norms are already introduced in India from 1st April 2020. The implementation of BS VI emission standards essentially brings Indian motor vehicle regulations on par with most stringent International standards. The BS VI regulation also mandated Real Driving Emission (RDE) measurement with objective to limit regulated pollutants esp. NOX & PN during real use of vehicle. For M1 passenger vehicles Carbon Dioxide (CO2) emissions measured in Lab is also regulated under CAFÉ (Corporate Average Fuel Economy) however, CO2 emission during Real on Road Driving is not regulated. So, this study was carried out to compare CO2 on real road traffic conditions with standard lab conditions. This study was done on a set of BS VI compliant vehicles with diverse characteristic such as engine capacity, fuel type.

Recently, Hybrid electric vehicles have become significant. Electric vehicle is still in its infancy while grappling with multiple solutions to its problem of range anxiety and heavy weight. It makes HEV the viable and intermediate solution which can facilitate the transition. The battery behaviour is grossly defined by its dependence on variation due to temperature change. Hence, this present work focuses on understanding thermal characterization & pure behaviour of the Li-Ion Phosphate (LiFePO4) P1-HEV battery using the HPPC test. This becomes imperative because of the varying driver demands and ambient temperatures over the use during the day. Thus, the current drawn from battery varies (different C rate) leading to heat generation (I2R heating) within the pack/individual cell. Cyclically, impacting the cell performance and battery cycle life.

Major cause of air pollution in the world is due to burning of fossil fuels for transport application; around 23% GHG emissions are produced due to transport sector. Likewise, the major cause of air pollution in Indian cities is also due to transport sector. Marginal improvement in the fuel economy provide profound impact on surrounding air quality and lightweighting of vehicle mass is the key factor in improving fuel economy. The paper describes robust and integrated approach used for design and development of lightweight bus structures for Indian city bus applications. An attempt is made to demonstrate the use of environment friendly material like aluminium in development of lightweight superstrutured city buses for India. Exercise involved design, development and prototype manufacturing of 12m Low Entry and 12m Semi Low Floor (SLF) bus models.