Search Results

Large two-stroke marine Diesel engines have special injector geometries, which differ substantially from the configurations used in most other Diesel engine applications. One of the major differences is that injector orifices are distributed in a highly non-symmetric fashion affecting the spray characteristics. Earlier investigations demonstrated the dependency of the spray morphology on the location of the spray orifice and therefore on the resulting flow conditions at the nozzle tip. Thus, spray structure is directly influenced by the flow formation within the orifice. Following recent Large Eddy Simulation resolved spray primary breakup studies, the present paper focuses on spray secondary breakup modelling of asymmetric spray structures in Euler-Lagrangian framework based on previously obtained droplet distributions of primary breakup.

Boosting and stratified operation can be used to increase the fuel efficiency of modern gasoline direct-injected (GDI) engines. In modern downsized GDI engines, boosting is standard to achieve a high power output. However, boosted GDI-engines have mostly been operated in homogenous mode and little is known about the effects of operating a boosted GDI-engine in stratified mode. This study employed optical and metal engines to examine how boosting influences combustion and particulate emission formation in a spray-guided GDI (SGDI), single cylinder research engine. The setup of the optical and metal engines was identical except the optical engine allowed optical access through the piston and cylinder liner. The engines were operated in steady state mode at five different engine operating points representing various loads and speeds. The engines were boosted with compressed air and operated at three levels of boost, as well as atmospheric pressure for comparison.

Passive selective catalyst reduction (SCR) systems can be used as aftertreatment systems for lean burn spark ignition (SI)-engines. Their operation is based on the interaction between the engine, an ammonia formation catalyst (AFC), and an SCR catalyst. Under rich conditions the AFC forms ammonia, which is stored in the SCR catalyst. Under lean conditions, the SCR catalyst reduces the engine out NOx using the stored NH3. This study compared the ammonia production and response times of a standard three way catalyst (TWC) and a Pd/Al2O3 catalyst under realistic engine operating conditions. In addition, the relationships between selected engine operating parameters and ammonia formation over a TWC were investigated, considering the influence of both the chosen load point and the engine settings.

Among many techniques used for increasing fuel efficiency of a modern Gasoline Direct-Injected (GDI) engine are boosting and stratified operation. In modern downsized GDI engines, boosting is standard in order to achieve a high power output. Boosted GDI-engines have however mostly been operated in homogenous mode and little is known on the effects of operating a boosted GDI-engine in stratified mode. This paper presents the influence on combustion, standard emissions and particulate size distribution in a Spray-Guided, Gasoline, Direct-Injected (SGDI), single cylinder, research engine operated with various levels of boost. The engine was operated in steady state mode at five engine operating points of various load and speed. The engine was boosted with a Roots blower and operated at four levels of boost as well as atmospheric pressure for comparison. The engine was fueled with market gasoline (95 RON) blended with 10% ethanol.

Commercial three way catalysts have limited capacity towards reducing NOx in the presence of excessive oxygen. This prevents lean-burn combustion concepts from meeting legislative emission standards. A solution towards decreasing NOx emissions in the presence of excess air is the use of a passive-SCR system. Under rich conditions ammonia is formed over an ammonia formation catalyst, the ammonia is stored in the SCR and in its turn reacts with the NOx under lean engine conditions. Here up-scaled Pt/Al2O3 and Pd/Al2O3 catalysts as well as a commercially Pd-Rh based three-way catalyst (TWC) are evaluated using both engine and further lab-scale tests. The purpose of these tests is to compare the ammonia production for the various catalysts under various lambda values and temperatures by means of engine and lab scale tests. The Pd/Al2O3 showed little sensitivity to temperature both under engine and lab scale experiments.

To contribute to knowledge required to meet new emission requirements, relationships between multiple injection parameters, degrees of fuel stratification, combustion events, work output and flame luminosity (indicative of particulate abundance) were experimentally investigated using a single-cylinder optical GDI engine. A tested hypothesis was that advancing portions of the mass injected would enhance the fuel-air mixing and thus reduce flame luminescence. An outward-opening piezo actuated fuel injector capable of multiple injections was used to inject the fuel using different triple injection strategies, with various combinations of late and earlier injections leading to various degrees of fuel stratification. Sprays and combustion events were captured using two high-speed cameras and cylinder pressure measurements.

On page 1103, the published paper omitted important text before and after figure 6.

Nowadays, much focus for vehicle manufacturers is directed towards improving the energy efficiency of their products. The aerodynamic drag constitutes one major part of the total driving resistance for a vehicle travelling at higher speeds. In fact, above approximately 80km/h the aerodynamic drag is the dominating resistance acting on a truck. Hence the importance of reducing this resistance is apparent. Cooling drag is one part of the total aerodynamic drag, which arises from air flowing through the heat exchangers, and the irregular under-hood area. When using Computational Fluid Dynamics (CFD) in the development process it is of great importance to ensure that the methods used are accurately capturing the physics of the flow. This paper deals with comparative studies between CFD and wind-tunnel tests. In this paper, two comparative studies are presented.

Parameter tuning was performed against data from a full scale engine rig with a Diesel Oxidation Catalysts (DOC). Several different catalyst configurations were used with varying Pt loading, washcoat thickness and volume. To illustrate the interplay between kinetics and mass transport, engine operating points were chosen with a wide variation in variables (inlet conditions) and both transient and stationary operation was used. A catalyst model was developed where the catalyst washcoat was discretized as tanks in series both radially and axially. Three different model configurations were used for parameter tuning, evaluating three different approaches to modeling of internal transport resistance. It was concluded that for a catalyst model with internal transport resistance the best fit could be achieved if some parameters affecting the internal mass transport were tuned in addition to the kinetic parameters.

There are a number of numerical and experimental studies of the aerodynamic performance of wheels that have been published. They show that wheels and wheel-housing flows are responsible for a substantial part of the total aerodynamic drag on passenger vehicles. Previous investigations have also shown that aerodynamic resistance moment acting on rotating wheels, sometimes referred to as ventilation resistance or ventilation torque is a significant contributor to the total aerodynamic resistance of the vehicle; therefore it should not be neglected when designing the wheel-housing area. This work presents a numerical study of the wheel ventilation resistance moment and factors that affect it, using computational fluid dynamics (CFD). It is demonstrated how pressure and shear forces acting on different rotating parts of the wheel affect the ventilation torque. It is also shown how a simple change of rim design can lead to a significant decrease in power consumption of the vehicle.

In recent years, a free, open source CFD software package called OpenFOAM has been attracting increasing amounts of attention as a promising, inexpensive, and efficient CFD tool for the numerical simulation of processes such as fuel injection and evaporation, turbulent mixing and burning. Here, we describe the further development of OpenFOAM to enable its use in simulating stratified turbulent combustion in DI SI engines. Advanced models of various phenomena relevant to partially premixed turbulent flames were implemented into the code, and the effects of these implementations were investigated by performing unsteady 3D RANS simulations of stratified turbulent burning in a DI SI engine. First, the Flame Speed Closure (FSC) model of premixed turbulent combustion was implemented. Second, a method for evaluating the mean density in premixed turbulent flames that is available in the standard OpenFOAM library was improved.

The effect of various fuel-cut agings, on a Volvo Cars 4-cylinder gasoline engine, with bimetallic three-way catalysts (TWCs) was examined. Deactivation during retardation fuel-cut (low load) and acceleration fuel-cut (high load, e.g. gearshift or traction control) was compared to aging at λ=1. Three-way catalysts were aged on an engine bench comparing two fuel-cut strategies and their impact on of the life and performance of the catalysts. In greater detail, the catalytic activity, stability and selectivity were studied. Furthermore, the catalysts were thoroughly analyzed using light-off and oxygen storage capacity measurements. The emission conversion as a function of various lambda values and loads was also determined. Fresh and 40-hour aged samples showed that the acceleration fuel-cut was the strategy that had the highest contribution towards the total deactivation of the catalyst system.

When performing catalyst modeling and parameter tuning it is desirable that the experimental data contain both transient and stationary points and can be generated over a short period of time. Here a method of creating such concentration transients for a full scale engine rig system is presented. The paper describes a valuable approach for changing the composition of engine exhaust gas going to a DOC (or potentially any other device) by conditioning the exhaust gas with an additional upstream DOC and/or SCR. By controlling the urea injection and the DOC bypass a wide range of exhaust compositions, not possible by only controlling the engine, could be achieved. This will improve the possibilities for parameter estimation for the modeling of the DOC.

In order to quantify fuel-cut aging effects on commercial bimetallic Pd/Rh three-way catalysts (TWCs), supported on cerium-zirconium promoted alumina, full-size automotive catalysts were exposed to accelerated fuel-cut aging on an engine test bench, with a variation in temperature, fuel-cut frequency and fuel-cut duration. After aging, samples of the catalysts were tested in a laboratory environment for Light-off temperature (T50), Specific surface area (BET), Dispersion of noble metals and changes in the oxidation state of Pd and Rh. The catalytic tests showed clear deactivation of the aged samples and influence on the TWC's properties. The light off temperature and noble metal dispersion were found to be a clear function of oxygen exposure to the catalysts, i.e. fuel-cut frequency and duration, while the specific surface area was found to be a function of fuel-cut frequency. No changes in oxidation states of Pd and Rh could be detected.

The EU emission standards for new rail Diesel engines are becoming even more stringent. EGR and SCR technologies can both be used to reduce NOx emissions; however, the use of EGR is usually accompanied by an increase in PM emissions and may require a DPF. On the other hand, the use of SCR requires on-board storage of urea. Thus, it is necessary to study these trade-offs in order to understand how these technologies can best be used in rail applications to meet new emission standards. The present study assesses the application of these technologies in Diesel railcars on a quantitative basis using one and three dimensional numerical simulation tools. In particular, the study considers a 560 kW railcar engine with the use of either EGR or SCR based solutions for NOx reduction. The NOx and PM emissions performances are evaluated over the C1 homologation cycle.

Passenger car fuel consumption is a constant concern for automotive companies and the contribution to fuel consumption from aerodynamics is well known. Several studies have been published on the aerodynamics of wheels. One area of wheel aerodynamics discussed in some of these earlier works is the so-called ventilation resistance. This study investigates ventilation resistance on a number of 17 inch rims, in the Volvo Cars Aerodynamic Wind Tunnel. The ventilation resistance was measured using a custom-built suspension with a tractive force measurement system installed in the Wheel Drive Units (WDUs). The study aims at identifying wheel design factors that have significant effect on the ventilation resistance for the investigated wheel size. The results show that it was possible to measure similar power requirements to rotate the wheels as was found in previous works.

Reducing resistance forces all over the vehicle is the most sustainable way to reduce fuel consumption. Aerodynamic drag is the dominating resistance force at highway speeds, and the power required to overcome this force increases by the power three of speed. The exterior body and especially the under-body and rear-end geometry of a passenger car are significant contributors to the overall aerodynamic drag. To reduce the aerodynamic drag it is of great importance to have a good pressure recovery at the rear. Since pressure drag is the dominating aerodynamic drag force for a passenger vehicle, the drag force will be a measure of the difference between the pressure in front and at the rear. There is high stagnation pressure at the front which requires a base pressure as high as possible. The pressure will recover from the sides by a taper angle, from the top by the rear wind screen, and from the bottom, by a diffuser.

This paper describes the design process of a full aerodynamic package of a Formula SAE (FSAE) style race car. The meaning of a full aerodynamic package in this context is a front wing, a rear wing and a diffuser; the focus will however be on the wings. The vehicle for which the aerodynamic package is designed is the Chalmers Formula Student (CFS) 2012 FSAE car, but vehicle data logged from the CFS 2011 FSAE car was used during the design phase. This data was used to evaluate how the aerodynamic package will influence the behaviour of the vehicle, both in terms of lateral and longitudinal acceleration as well as fuel consumption, in order to determine whether or not an aerodynamic package can enhance the vehicle performance. The main tool used during the design process was numerical simulations (computational fluid dynamics, CFD) and special attention was paid to post-processing of these simulations.

A regular flex-fuel engine can operate on any blend of fuel between pure gasoline and E85. Flex-fuel engines have relatively low efficiency on E85 because the hardware is optimized for gasoline. If instead the engine is optimized for neat ethanol, the efficiency may be much higher, as demonstrated in this paper. The studied two-liter engine was modified with a much higher compression ratio than suitable for gasoline, two-stage turbocharging and direct injection with piezo-actuated outwards-opening injectors, a stratified combustion system and custom in-house control system. The research engine exhibited a wide-open throttle performance similar to that of a naturally aspirated v8, while offering a part-load efficiency comparable to a state-of-the-art two-liter naturally aspirated engine. NOx will be handled by a lean NOx trap. Combustion characteristics were compared between gasoline and neat ethanol.

An important objective in combustion engine research is to develop strategies for recovering waste heat and thereby increasing the efficiency of the propulsion system. Waste-heat recovery systems based on the Rankine cycle are the most efficient tools for recovering energy from the exhaust gas and the Exhaust Gas Recirculation (EGR) system. The properties of the working fluid and the expansion machine have significant effects on Rankine cycle efficiency. The expansion machine is particularly important because it is the interface at which recovered heat energy is ultimately converted into power. Parameters such as the pressure, temperature and mass-flow conditions in the cycle can be derived for a given waste-heat source and expressed as dimensionless numbers that can be used to determine whether displacement expanders or turbo expanders would be preferable under the circumstances considered.