Search Results

When designing an electric vehicle (EV) traction system, overcoming the issues arising from the variations in the battery voltage due to the state of charge (SoC) is critical, which otherwise can lead to a deterioration of the powertrain energy efficiency and overall drive performance. However, systems are typically documented under fixed voltage and temperature conditions, potentially lacking comprehensive specifications that account for these variations across the entire range of the vehicle operating regions. To tackle this challenge, this paper seeks to adjust an optimal DC-link voltage across the complete range of drive operating conditions by integrating a DC-DC converter into the powertrain, thereby enhancing powertrain efficiency. This involves conducting a comprehensive analysis of power losses in the power electronics of a connected converter-inverter system considering the temperature variations, along with machine losses, accounting for variable DC-link voltages.

The need for a more complete understanding of the flow behavior in aerodynamic wind tunnels has increased as they have become vital tools not only for vehicle development, but also for vehicle certification. One important aspect of the behavior is the empty test section flow, which in a conventional tunnel should be as uniform as possible. In order to assess the uniformity and ensure consistent behavior over time, accurate measurements need to be performed regularly. Furthermore, the uncertainties and errors of the measurements need to be minimized in order to resolve small non-uniformities. In this work, the quantification of the measurement uncertainties from the full measurement chain of the new flow uniformity measurement rig for the Volvo Cars aerodynamic wind tunnel is presented. The simulation based method used to account for flow interference of the probe mount is also discussed.

In the next 20 years the share of small electric vehicles (SEVs) will increase especially in urban areas. SEVs show distinctive design differences compared to traditional vehicles. Thus the consequences of impacts of SEVs with vulnerable road users (VRUs) and other vehicles will be different from traditional collisions. No assessment concerning vehicle safety is defined for vehicles within European L7e category currently. Focus of the elaborated methodology is to define appropriate test scenarios for this vehicle category to be used within a virtual tool chain. A virtual tool chain has to be defined for the realization of a guideline of virtual certification. The derivation and development of new test conditions for SEVs are described and are the main focus of this work. As key methodology a prospective methodical analysis under consideration of future aspects like pre-crash safety systems is applied.

Pedestrians and bicyclists account for a significant share of deaths and serious injuries in the road transport system. The protection of pedestrians in car-to-pedestrian crashes has therefore been addressed by friendlier car fronts and since 1997, the European New Car Assessment Program (Euro NCAP) has assessed the level of protection for most car models available in Europe. In the current study, Euro NCAP pedestrian scoring was compared with real-life injury outcomes in car-to-pedestrian and car-to-bicyclist crashes occurring in Sweden. Approximately 1200 injured pedestrians and 2000 injured bicyclists were included in the study. Groups of cars with low, medium and high pedestrian scores were compared with respect to pedestrian injury severity on the Maximum Abbreviated Injury Scale (MAIS)-level and risk of permanent medical impairment (RPMI). Significant injury reductions to both pedestrians and bicyclists were found between low and high performing cars.

The aim of this study was to identify and measure time-consuming human modelling tool activities. Five human modelling tool users at Volvo were observed for five days each. The results showed a wide distribution of both indirect and direct working tasks, as well as non-value added tasks such as waiting time. Most of the activities identified appear to be necessary to perform human modelling simulations of high quality. However, the time distribution could be questioned to some extent. There are many activities associated with communication, including a variety of contacts and meetings, where there appears to be potential to increase efficiency.

The objective of this paper is to investigate whether different appearance modes of the digital human models (DHM or manikins) affect the observers when judging a working posture. A case where the manikin is manually assembling a battery in the boot with help of a lifting device is used in the experiment. 16 different pictures were created and presented for the subjects. All pictures have the same background, but include a unique posture and manikin appearance combination. Four postures and four manikin appearances were used. The subjects were asked to rank the pictures after ergonomic assessment based on posture of the manikin. Subjects taking part in the study were either manufacturing engineering managers, simulation engineers or ergonomists. Results show that the different appearance modes affect the ergonomic judgment. A more realistic looking manikin is rated higher than the very same posture visualized with a less natural appearance.

This paper presented a part of results from an ongoing project for pedestrian protection, which is carried out at Chalmers University of Technology in Sweden. A validated pedestrian mathematical model was used in this study to simulate vehicle-pedestrian impacts. A large number of simulations have been carried out with various parameters. The injury-related parameters concerning head, chest, pelvis and lower extremities were calculated to evaluate the effect of impact speed and vehicle front structure on the risk of pedestrian injuries. The effect of following vehicle parameters was studied: stiffness of bumper, hood edge, hood top, windscreen frame, and shape of vehicle front structures. A parameter study was conducted by modelling vehicle-pedestrian impacts with various sizes of cars, mini vans, and light trucks. This choice represents the trends of new vehicle fleet and their frequency of involvement in real world accidents.

Several investigators have noted limitations of the most commonly used dummy in rear impact testing, the Hybrid III. A dummy for rear impact testing, the BioRID I, has previously been presented. It was a step towards an effective tool for seat performance testing, but it was concluded that its neck extension and T1 upward motion were too small and that its user- friendliness could be improved. A new BioRID prototype has been developed. It has new neck muscle substitutes with damping and elastic elements that are independent of each other and fitted inside the torso. The new neck muscle substitutes extend to T3 and thus also load the upper thoracic spine. The new dummy has a softer thoracic spine and a torso made of softer rubber than was used for the original dummy. The BioRID prototype''s performance was compared to that of volunteers, the BioRID I and Hybrid III in rear impacts at ΔV=7 km/h.

In the ANNIE project - Applications of Neural Networks to Integrated Ergonomics - BE96-3433, a tool for integrating ergonomics into the design process is developed. This paper presents some features in the current ANNIE as applied to the design of car interiors. A variant of the ERGOMan mannequin with vision is controlled by a hybrid system for neuro-fuzzy simulation. It is trained by using an Elite system for registration of movements. An example of a trajectory generated by the system is shown. A fuzzy model is used for comfort evaluation. An experiment was performed to test its feasibility and it showed very promising results.

The shearing and bending injury mechanisms of the knee joint are recognised as two important injury mechanisms associated with car-pedestrian crash accidents. A study on shearing and bending response of the knee joint to a lateral impact loading was conducted with a 3D multibody system model of the lower extremity. The model consists of foot, leg and thigh with concentrated upper body mass. The body elements are connected by joints, including an anatomical knee joint unit that consists of the femur condyles, tibia condyles and tibia1 intercondylar eminence as well as ligaments. The biomechanical properties of the model were derived from literature data. The model was used to simulate two series of previously performed experiments with lower extremity specimens at lateral impact speeds of 15 and 20 km/h.

A 3D pedestrian knee joint model was developed as a first step in a new description of the whole pedestrian body for computer simulations. The model was made to achieve better correlation with the results from previous tests with biological material. The model of the knee joint includes the articular surfaces, ligaments and capsule represented by the ellipsoid and plane elements as well as the spring-damping elements, respectively. The mechanical properties of the knee joint were based on available biomechanical data. To verify the new developed model with results from tests with biological material previously performed at the Department of Injury Prevention, Chalmers University of Technology, the computer simulations were carried out with the model of the knee joint using the MADYMO 3D program.

The INCOLL or INertia COLLection system described in this paper, should meet the requirements for a short transient test, without using any chassis dynamometer. To prove this point not only the background of its principles are described, but also results from its application both to S I engines with and without catalytic converters and to truck diesel engines. Special interest has been devoted to the oxygen sensor and converter efficiency and their response both during warm up and under transient conditions. The simplification of the analyzing equipment and the direct interpretation of the results, have been dealt with, as well as the repeativity of the results achieved. The INCOLL test may also have a potential use as quality test at the end of the production line and as a tool for reliability development as well as research and development within the field. The cost for an INCOLL test is estimated to be around one (1) percent of a normal FTP certification procedure.