Search Results

DENSO started a pilot demonstration of on-site methanation as “CO2 circulation plant” as proactive initiative for CO2 capture and storage/utilization (CCUS) technologies toward achievement of carbon neutrality by 2035 in our own business. The CO2 circulation plant was designed to capture CO2 primarily generated by the plant and recycle it as an energy source of the facility. We also started work on the development of electric swing CO2 adsorption (ESA) technology to achieve low-energy CO2 capture.

We have developed a novel wafer process for capacitive sensing accelerometer using surface Micro Electrical Mechanical Systems (MEMS) technology and successfully applied to the fabrication process. Our new process combines with a single crystal SOI (Si on Insulator) wafer, high aspect ratio silicon etching and newly developed anhydrous HF/Alcohol etch process of silicon oxides. Although wet conditions such as HF/water etch occurs stiction of mobile structure, our anhydrous HF/Alcohol etch process technology occurs no stiction of mobile structures, because of gas phase (dry) process. In our process, we have achieved smaller-sized sensor chip compared to our conventional 2 axes accelerometer.

We have developed a novel capacitive acceleration sensor fabrication process by applying surface MEMS (Micro Electro-Mechanical System) technology and successfully introduced this process for volume production of a new super slim sensor. The new process uses the ICP-RIE(Inductively Coupled Plasma - Reactive Ion Etching) technology to etch single crystal SOI(Si on Insulator wafers. In this technology, vertical Si etching is followed by, lateral etching along the buried oxide to release the movable electrode. Because of a dry process, the new process does not cause the movable structures to stick to each other. Our process uses only three masks and reduces the sensor chip size to a half that of our conventional capacitive acceleration sensors.

Carbon brushes for automotive starters are used under severe conditions of high electric current density, high contact pressure and high sliding velocity. Therefore lead has traditionally been added to brushes to improve performance and durability. Lead is an environmental hazardous substance. In the EU, the law prohibits adding lead to brushes for electric motors which is installed on new automobiles in and after January 2005. In order to develop the lead free carbon brush for starters, we analyzed the effect and selected substitutive substance of lead. Adding lead to the brush reduces the electric resistance increase of the brush in high-temperature and high-humidity atmosphere and in high-temperature atmosphere. Furthermore lead reduces the wear amount of brush. We developed the lead free brush surpassing the lead addition brush in performance and durability by addition of lead alternatives silver and zinc.

A recent trend in the making of automotive engines, where high efficiency and low emissions need to be considered, is to mount multiple parts around the motor in order to improve overall engine efficiency. As a result of modern technology, the engine head and surrounding space have an excessive amount of parts. To accommodate the congested engine compartment, it is desirable to reduce the size of the spark plug. Small size spark plugs have the problem of poor resistance to carbon fouling and are subject to side sparks if carbon fouling occurs. This results from a reduced insulating gap between the center electrode and the housing achieved by reducing the size of the spark plug. By using visualization of flame growth and electric field strength analysis, we have conducted studies on insulator temperatures and spark behaviors in search of the optimal specifications.

Increasing electric loads in a vehicle causes over-discharge of a battery and drag torque due to an alternator. This paper gives a system concept of vehicle electric power flow management to solve these issues. Its primary function includes preserving electricity in a battery, stabilizing electric bus voltage, interfacing with vehicle torque control system, and improving fuel economy. The key point to realize such a system is a unified structure. It offers ‘Plug and Play’ function for electric power management components. Newly developed Vehicle Electric Power Flow Management System (VEF ) totally controls electric power flow in a vehicle. VEF contains an Electric Power Manager and its functional sub-systems, and controls them with the key parameter ‘electric power’. The sub-system includes Generation, Storage, Conversion, and Distribution to the loads.

Up to now, while automobile electric packages have demanded the high density for small and light products, electric leaks, which have occurred due to condensation, have been a major problem. To prevent any electric leaks, a conformal coating on the electric parts (ex. ECU: Electronic Control Unit) has been needed, but in general the design rules of the conformal coating (ex. Application area) is vague. Therefore, DENSO demands to clear the design rules of conformal coating electric package for higher reliability. To meet the demand, DENSO has developed a condensation simulation method using CAE that can show the occurrence condition of condensation fast and accurately. In the result, DENSO has been able to get the design rules where to need the conformal coating in the electric package for automobiles.

In a conventional soldering process, solvents, such as chlorofluorocarbons (CFCs), have been necessary to remove the flux-residue after soldering. A new CFC-free fluxless soldering process has been developed to obtain high sealing ability even in a small soldering area. This new process utilizes a reducing atmosphere with an appropriate load and assembly orientation to solder the parts. Under this fluxless condition, it is found that appropriate loading and good solder-wettability of the upper part increase the wettability of the lower part.

There has recently been an increasing need in various automotive monitoring and control systems for a simply structured and highly reliable high-pressure sensor to detect the higher pressures of oils, hydraulic fluids, air and air conditioning refrigerants. A simple, newly devised approach to sealing oil filled high-pressure sensors is introduced in this paper. The new structure utilizes a resin instead of the metal and glass conventionally used for hermetic sealing oil filled high-pressure sensors. This is made possible by the combined use of oils with large effective molecular diameters and carefully optimized design of shape and size of the sealing faces between sensor parts. The use of a sealed metal diaphragm allows for extensive use of the sensor with many different kinds of pressure media and in various applications.