Search Results

Reducing vehicle CO2 emissions is an important measure to help address global warming. To reduce CO2 emissions on a global basis, Toyota Motor Corporation is taking a multi-pathway approach that involves the introduction of the optimal powertrains according to the circumstances of each region, including hybrid electric (HEVs) and plug-in hybrid electric vehicles (PHEVs), as well as battery electric vehicles (BEVs). This report describes the development of a new PHEV system for the Toyota Prius. This system features a traction battery pack structure, transaxle, and power control unit (PCU) with boost converter, which were newly developed based on the 2.0-liter HEV system. As a result, the battery capacity was increased by 1.5 times compared to the previous model with almost the same battery pack size. Transmission efficiency was also improved, extending the distance that the Prius can be driven as an EV by 70%.

DENSO started a pilot demonstration of on-site methanation as “CO2 circulation plant” as proactive initiative for CO2 capture and storage/utilization (CCUS) technologies toward achievement of carbon neutrality by 2035 in our own business. The CO2 circulation plant was designed to capture CO2 primarily generated by the plant and recycle it as an energy source of the facility. We also started work on the development of electric swing CO2 adsorption (ESA) technology to achieve low-energy CO2 capture.

In general, automatic braking uses an electric stability control (ESC) hydraulic unit that can automatically increase the hydraulic pressure in the wheel cylinder (hereinafter called wheel pressure), independent of the driver’s braking operation. The hydraulic unit should have sufficient pressure response to apply autonomous emergency braking (AEB). It was necessary for the hydraulic unit to have a high flow rate for the pressure response. To satisfy the performance requirements of the AEB, a brushless motor, which has a high maximum rotational speed and good response, is adopted for the hydraulic unit. Furthermore, sensorless control, which does not require a rotation angle sensor, has been developed so that the motor size can be small and common to conventional units. The developed sensorless control can switch the driving methods in three states: pre-rotation, low speed, and high speed.

Toyota Motor Corporation has developed a new battery electric vehicle (BEV) on the dedicated e-TNGA platform for BEVs, which was designed to lower the center of gravity of the vehicle and increase body stiffness. In addition to a full-time 4WD system, another feature of this new BEV is its pleasurable driving experience. A new inverter drive unit was developed for this system. Unlike the previous inverter, the advantage of the new inverter is that it is small enough to be mounted inside the transaxle housing, thereby contributing to the availability of interior and luggage space. The temperature rise of the power semiconductors in the inverter was reduced considerably by the development of a new power semiconductor for BEVs. This enables a parallel layout of two power semiconductors instead of three. The components of the inverter were also downsized. A coreless current sensor was adopted, and capacitors were developed with significantly lower capacitance.

In Japan, from the viewpoint of ozone layer protection, specified CFCs (Chlorofluorocarbons) phase-out started in 1992 and completed by 1995. HFC-134a (Hydro fluorocarbon-134a) is now dominant in the market. HFC-134a, the replacement, has zero ozone depleting potential, while it still has a higher global warming potential (GWP = 1430). In this paper, efforts of DENSO and the Japanese industry from aspects of refrigerant emission reduction and energy efficiency improvement are introduced.

A lot of electric components have been installed in a vehicle today for comfort, safety and environment. This tendency is said to be continued in the future. Therefore, additional power supplies such as exhaust gas electricity generation system and thermal electricity generation system have been developed in the world to supply additional electricity as well as an enlargement of an alternator. However, if these new electricity supply systems are installed in a present electric power system that is controlled based on a voltage feedback, each supply system cannot be controlled effectively, because it is difficult to control output power of each system independently. An electric power based control system, Vehicle Electric power Flow management system (VEF), has been developed to avoid this problem. Sum of required electric power is calculated based on electric loads power and battery charging power. This required power is allocated to each power supply system.

Carbon brushes for automotive starters are used under severe conditions of high electric current density, high contact pressure and high sliding velocity. Therefore lead has traditionally been added to brushes to improve performance and durability. Lead is an environmental hazardous substance. In the EU, the law prohibits adding lead to brushes for electric motors which is installed on new automobiles in and after January 2005. In order to develop the lead free carbon brush for starters, we analyzed the effect and selected substitutive substance of lead. Adding lead to the brush reduces the electric resistance increase of the brush in high-temperature and high-humidity atmosphere and in high-temperature atmosphere. Furthermore lead reduces the wear amount of brush. We developed the lead free brush surpassing the lead addition brush in performance and durability by addition of lead alternatives silver and zinc.

Increasing electric loads in a vehicle causes over-discharge of a battery and drag torque due to an alternator. This paper gives a system concept of vehicle electric power flow management to solve these issues. Its primary function includes preserving electricity in a battery, stabilizing electric bus voltage, interfacing with vehicle torque control system, and improving fuel economy. The key point to realize such a system is a unified structure. It offers ‘Plug and Play’ function for electric power management components. Newly developed Vehicle Electric Power Flow Management System (VEF ) totally controls electric power flow in a vehicle. VEF contains an Electric Power Manager and its functional sub-systems, and controls them with the key parameter ‘electric power’. The sub-system includes Generation, Storage, Conversion, and Distribution to the loads.

Up to now, while automobile electric packages have demanded the high density for small and light products, electric leaks, which have occurred due to condensation, have been a major problem. To prevent any electric leaks, a conformal coating on the electric parts (ex. ECU: Electronic Control Unit) has been needed, but in general the design rules of the conformal coating (ex. Application area) is vague. Therefore, DENSO demands to clear the design rules of conformal coating electric package for higher reliability. To meet the demand, DENSO has developed a condensation simulation method using CAE that can show the occurrence condition of condensation fast and accurately. In the result, DENSO has been able to get the design rules where to need the conformal coating in the electric package for automobiles.