Search Results

A single-cylinder engine was used to study the potential of a high-efficiency combustion concept called gasoline direct-injection compression-ignition (GDCI). Low temperature combustion was achieved using multiple injections, intake boost, and moderate EGR to reduce engine-out NOx and PM emissions engine for stringent emissions standards. This combustion strategy benefits from the relatively long ignition delay and high volatility of regular unleaded gasoline fuel. Tests were conducted at 6 bar IMEP - 1500 rpm using various injection strategies with low-to-moderate injection pressure. Results showed that triple injection GDCI achieved about 8 percent greater indicated thermal efficiency and about 14 percent lower specific CO2 emissions relative to diesel baseline tests on the same engine. Heat release rates and combustion noise could be controlled with a multiple-late injection strategy for controlled fuel-air stratification. Estimated heat losses were significantly reduced.

Global demand for alternative fuels to combat rising energy costs has sparked a renewed interest in catalysts that can effectively remediate NOx emissions resulting from combustion of a range of HC based fuels. Because many of these new engine technologies rely on lean operating environments to produce efficient power, the resulting emissions are also present in a lean atmosphere. While HCs are easily controlled in such environments, achieving high NOx conversion to N2 has continued to elude fully satisfactory solution. Until recently, most approaches have relied on catalysts with precious metals to either store NOx and subsequently release it as N2 under rich conditions, or use NH3 SCR catalysts with urea injection to reduce NOx under lean conditions. However, new improvements in Ag based technologies also look very promising for NOx reduction in lean environments.

Low-cost lean NOx aftertreatment is one of the main challenges facing high-efficiency gasoline and diesel engines operating with lean mixtures. While there are many candidate technologies, they all offer tradeoffs. We have investigated a multi-component Dual SCR aftertreatment system that is capable of obtaining NOx reduction efficiencies of greater than 90% under lean conditions, without the use of precious metals or urea injection into the exhaust. The Dual SCR approach here uses an Ag HC-SCR catalyst followed by an NH3-SCR catalyst. In bench reactor studies from 150 °C to 500 °C, we have found, for modest C/N ratios, that NOx reacts over the first catalyst to predominantly form nitrogen. In addition, it also forms ammonia in sufficient quantities to react on the second NH3-SCR catalyst to improve system performance. The operational window and the formation of NH3 are improved in the presence of small quantities of hydrogen (0.1–1.0%).

As diesel emission regulations continue to increase, the use of exhaust aftertreatment systems containing, for example the diesel oxidation catalyst (DOC) and diesel particulate filter (DPF) will become necessary in order to meet these stringent emission requirements. The addition of a DOC and DPF in conjunction with utilizing biodiesel fuels requires extensive research to study the implications that biodiesel blends have on emissions as well as to examine the effect on aftertreatment devices. The proceeding work discusses results from a 2006 VM Motori four-cylinder 2.8L direct injection diesel engine coupled with a diesel oxidation catalyst and catalyzed diesel particulate filter. Tests were done using ultra low sulfur diesel fuel blended with 20% choice white grease biodiesel fuel to evaluate the effects of biodiesel emission products on the performance and effectiveness of the aftertreatment devices and the effect of low temperature combustion modes.

The need for improved emissions control in lean exhaust to meet tightening, world-wide NOx emissions standards has led to the development of selective catalytic reduction of NOx with ammonia as a major technology for emissions control. Current systems are being designed to use a solution of urea (32.5 wt %) dissolved in water or Diesel Exhaust Fluid (DEF) as the ammonia source. While DEF or AdBlue® is widely used as a source of ammonia, it has a number of issues at low temperatures, including freezing below −12 °C, solid deposit formation in the exhaust, and difficulties in dosing at exhaust temperatures below 200 °C. Additionally creating a uniform ammonia concentration can be problematic, complicating exhaust packaging and usually requiring a discrete mixer.

In light of the growing emphasis on CO2 emissions reduction, Delphi has undertaken an internal development program to show the fuel economy benefits of lean, stratified combustion with its outwardly-opening solenoid injector in a vehicle environment. This paper presents the status of this ongoing development activity which is not yet completed. Progress to date includes a logical progression from single- and multi-cylinder dynamometer engines to the vehicle environment. The solenoid-actuated injector used in this development has an outwardly-opening valve group to generate a hollow-cone spray with a stable, well-defined recirculation zone to support spray-guided stratification in the combustion chamber. The engine management system of the development vehicle was modified from series-production configuration by changing the engine control unit to permit function development and calibration.

Selective Catalytic Reduction (SCR) is the dominant solution for meeting future NOx reduction regulations for heavy-duty diesel powertrains. SCR systems benefit from closed-loop control if an appropriate exhaust gas sensor were available. An ammonia sensor has recently been developed for use as a feedback element in closed-loop control of urea dosing in a diesel SCR aftertreatment system. Closed-loop control of SCR dosing enables the SCR system to be robust against disturbances and to meet conformity of production (COP) and in-use compliance norms. The ammonia sensor is based on a non-equilibrium electrochemical principle and outputs emf signals. The sensor performs well when tested in a diesel engine exhaust environment and has minimum cross interference with CO, HC, NO, NO2, SO2, H2O and O2. Previous work, done in a simulation environment, demonstrated that an ammonia sensor provides the optimal feedback for urea dosing control algorithms in closed-loop SCR systems.

The paper describes a new strategy for real-time sensor diagnostics that is based on the statistical correlation of various sensor signal pairs. During normal fault-free operation there is a certain correlation between the sensor signals which is lost in the event of a fault. The proposed algorithm quantifies the correlation between sensor signal pairs using real-time scalar metrics based on the Mahalanobis-distance concept. During normal operation all metrics follow a similar pattern, however in the event of a fault; metrics involving the faulty sensor would increase in proportion to the magnitude of the fault. Thus, by monitoring this pattern and using a suitable fault-signature table it is possible to isolate the faulty sensor in real-time. Preliminary simulation results suggest that the strategy can mitigate the false-alarms experienced by most model-based diagnostic algorithms due to an intrinsic ability to distinguish nonlinear vehicle behavior from actual sensor faults.

A key quantity for use in engine control is the exhaust manifold pressure. For production applications it is an important component in the calculation of the engine volumetric efficiency, as well as EGR flow and residual fraction. For cost reasons, however, it is preferable to not have to measure the exhaust manifold pressure for production applications. For that reason, it is advantageous to develop a model for estimating the exhaust manifold pressure in production application software that is small, accurate, and simple to calibrate. In this paper, a mean-value model for calculating the exhaust manifold pressure is derived from the compressible flow equation, treating the exhaust system as a fixed-geometry restriction between the exhaust manifold and the outlet of the tailpipe. Validation data from production applications is presented.

This paper includes a numerical and experimental study of fluid flow in automotive catalytic converters. The numerical work involves using computational fluid dynamics (CFD) to perform three-dimensional calculations of turbulent flow in an inlet pipe, inlet cone, catalyst substrate (porous medium), outlet cone, and outlet pipe. The experimental work includes using hot-wire anemometry to measure the velocity profile at the outlet of the catalyst substrate, and pressure drop measurements across the system. Very often, the designer may have to resort to offset inlet and outlet cones, or angled inlet pipes due to space limitations. Hence, it is very difficult to achieve a good flow distribution at the inlet cross section of the catalyst substrate. Therefore, it is important to study the effect of the geometry of the catalytic converter on flow uniformity in the substrate.

A new optimal control strategy for dealing with braking actuator failures in a vehicle equipped with a brake-by-wire and steer-by- wire system is described. The main objective of the control algorithm during the failure mode is to redistribute the control tasks to the functioning actuators, so that the vehicle performance remains as close as possible to the desired performance in spite of a failure. The desired motion of the vehicle in the yaw plane is determined using driver steering and braking inputs along with vehicle speed. For the purpose of synthesizing the control algorithm, a non-linear vehicle model is developed, which describes the vehicle dynamics in the yaw plane in both linear and non-linear ranges of handling. A control allocation algorithm determines the control inputs that minimize the difference between the desired and actual vehicle motions, while satisfying all actuator constraints.

Close-coupled or manifold catalysts have been extensively employed to reduce emissions during cold start by achieving quick catalyst light-off. These catalysts must have good thermal durability, high intrinsic light-off activity and high HC/CO/NOx conversions at high temperature and flow conditions. A number of studies have been dedicated to engine control, manifold design and converter optimization to reduce cold start emissions. The current paper focuses on the effect of catalyst design parameters and their performance response to different engine operating conditions. Key design parameters such as catalyst formulation (CeO2 vs. non CeO2), precious metal loading and composition (Pd vs. Pd/Rh), washcoat loading, catalyst thermal mass, substrate properties and key application (in use) parameters such as catalyst aging, exhaust A/F ratio, A/F ratio modulation, exhaust temperature, temperature rise rate and exhaust flow rate were studied on engine dynamometers in a systematic manner.

This paper reviews the current strategies for physical prototyping of Magnesium instrument panel (I/P) structures. Bottlenecks in the traditional physical prototype based product development process are discussed. As demand for fast-to-market and cost-reduction mounts, virtual prototyping becomes increasingly important in meeting the timing and performance goals. A virtual prototyping methodology is presented in this paper to enable high performance Magnesium I/P structures in Safety, NVH, and initial part quality aspects. Examples of Finite Element Analysis (FEA) results and correlations are included.

Execution of a software safety program is an accepted best practice to help verify that potential software hazards are identified and their associated risks are mitigated. Successful execution of a software safety program involves selecting and applying effective analysis methods and tasks that are appropriate for the specific needs of the development project and that satisfy software safety program requirements. This paper describes the effective application of a set of software safety methods and tasks that satisfy software safety program requirements for many applications. A key element of this approach is a tightly coupled fault tree analysis and failure modes and effects analysis. The approach has been successfully applied to several automotive embedded control systems with positive results.

Segmented, Silicon-Carbide Diesel Particulate Filters appear to be automotive industry's popular choice for reducing particulate emissions of Diesel Engines, particularly for light duty platforms. Since flow resistance represents an important performance feature of a filter, it is important that reasonable prediction tools for such filters are developed for use in their development, design, applications and regeneration control. A model for predicting pressure drop of segmented filters is presented here: an existing, well-accepted pressure drop model for monolithic (non-segmented) filters is customized to one for a segmented filter using a ‘weighted number of inlet channels’ based on equivalent filtration wall area of a monolithic filter. Flow resistance data collected experimentally on segmented filters are used to demonstrate the accuracy of the new model.

A steering wheel is an indispensable component in an automobile. Although the steering wheel was invented about one hundred years ago and its structure has since become more and more complex with numerous innovations, documented analysis on steering wheel performance is very limited. Today, a steering wheel is not only a wheel that controls where your car goes; it also plays an important role in a vehicle occupant protection system. Therefore, many requirements have to be met before a steering wheel goes into production. With the development of computational mechanics and increasing computer capability, it has become much easier to evaluate the steering wheel performance in a totally different way. Instead of running prototype tests, steering wheel designs can be modeled virtually in various scenarios using finite element analysis, thus facilitating the development cycle.

The perceived interior noise has been one of the major driving factors in the design of automotive interior assemblies. Buzz, Squeak and Rattle (BSR) issues are one of the major contributors toward the perceived quality in a vehicle. Traditionally BSR issues have been identified and rectified through extensive hardware testing. In order to reduce the product development cycle and minimize the number of costly hardware builds, however, one must rely on engineering analysis and simulation upfront in the design cycle. In this paper, an analytical and experimental study to identify potential BSR locations in a cockpit assembly is presented. The analytical investigation utilizes a novel and practical methodology, implemented in the software tool Nhance.BSR, for identification and ranking of potential BSR issues. The emphasis here is to evaluate the software for the BSR predictions and the identification of modeling issues, rather than to evaluate the cockpit design itself for BSR issues.

This paper proposes the concept of Generalized Diagnostic Component (GDC) and presents a modular fault diagnostic strategy for safety critical automotive systems. The diagnostic strategy makes full use of hierarchical techniques, integrates the generalized diagnostic design into all-purpose vehicle diagnoses based on reconfiguration of the GDCs, and inherits the model-based diagnostic algorithms developed for Steering/Braking-By-Wire systems. The GDC-based approach simplifies the design and integration of diagnostics in complex dynamical control systems, and has been successfully implemented in an eight degrees of freedom NAVDyn (Non-Linear Analysis of Vehicle Dynamics) simulation model using Matlab Simulink. The simulation results are provided in this paper to testify that the diagnostic strategy and implementation are feasible, efficient and dependable.

This paper reviews the state of the art on analytical design of cockpit modules in two most crucial performance categories: safety and comfort. On safety, applications of finite element analysis (FEA) for achieving robust designs that meet FMVSS 201, 208 and 214 requirements and score top frontal and side NCAP star-ratings are presented. On comfort, focus is placed on Noise, Vibration and Harshness (NVH) performance. Cutting-edge analytical tools for Buzz, Squeak and Rattle (BSR) avoidance and passenger compartment noise reduction are demonstrated. Most of the analytical results shown in this paper are based on the development work of a real-life application program. Correlations between the analytical results and physical test results are included. Examples of Computational Fluid Dynamics (CFD) analysis for climate control are also included. At the end, the road map toward 100 percent virtual prototyping and validation is presented.

Computer modeling and simulation have become one of the primary methods for development and design of automobile occupant protection systems (OPS). To ensure the accuracy and reliability of a math-based OPS design, the correlation quality assessment of mathematical models is essential for program success. In a typical industrial approach, correlation quality is assessed by comparing chart characteristics and scored based on an engineer's modeling experience and judgment. However, due to the complexity of the OPS models and their responses, a systematic approach is needed for accuracy and consistency. In this paper, a correlation grading methodology for the OPS models is presented. The grading system evaluates a wide spectrum of a computer model's performances, including kinematics, dynamic responses, and dummy injury measurements. Statistical analysis is utilized to compare the time histories of the tested and simulated dynamic responses.