Search Results

The current simulation models of EV and ICE Vehicles are well known in industry for their use in estimating the fuel economy or Range benefits because of controller calibrations and component sizing. However, there is a gap in understanding the behavior of accessories such as HVAC, power steering and other such auxiliary loads and the energy losses associated with them. Impact of thermal behavior of electronics on vehicle range also needs to be studied in detail. These kinds of studies help OEM and tier 1 manufactures in improving their design concepts significantly with minimum cost and development time. Hence, the focus of this study is on building simulation models of thermal, electrical, traction and control circuits of a typical electric vehicle. These models are then integrated, and analysis is performed to understand vehicle system level performance metrics.

Commercial vehicles require fast aftertreatment heat-up in order to move the SCR catalyst into the most efficient temperature range to meet upcoming NOX regulations. Today’s diesel aftertreatment systems require on the order of 10 minutes to heat up during a cold FTP cycle. The focus of this paper is to heat up the aftertreatment system as quickly as possible during cold starts and maintain a high temperature during low load, while minimizing fuel consumption. A system solution is demonstrated using a heavy-duty diesel engine with an end-of-life aged aftertreatment system targeted for 2027 emission levels using various levels of controls. The baseline layer of controls includes cylinder deactivation to raise the exhaust temperature more than 100° C in combination with elevated idle speed to increase the mass flowrate through the aftertreatment system. The combination yields higher exhaust enthalpy through the aftertreatment system.

Diesel Cylinder Deactivation (CDA) has been shown in previous work to increase exhaust temperatures, improve fuel efficiency, and reduce engine-out NOx for engine loads up to 3 bar BMEP. The purpose of this study is to determine whether or not the turbocharger needs to be altered when implementing CDA on a diesel engine. This study investigates the effect of CDA on exhaust temperature, fuel efficiency, and turbocharger performance in a 15L heavy-duty diesel engine under low-load (0-3 bar BMEP) steady-state operating conditions. Two calibration strategies were evaluated. First, a “stay-hot” thermal management strategy in which CDA was used to increase exhaust temperature and reduce fuel consumption. Next, a “get-hot” strategy where CDA and elevated idle speed was used to increase exhaust temperature and exhaust enthalpy for rapid aftertreatment warm-up.

Diesel engine cylinder deactivation (CDA) can be used to reduce petroleum consumption and greenhouse gas (GHG) emissions of the global freight transportation system. Heavy duty trucks require complex exhaust aftertreatment (A/T) in order to meet stringent emission regulations. Efficient reduction of engine-out emissions require a certain A/T system temperature range, which is achieved by thermal management via control of engine exhaust flow and temperature. Fuel efficient thermal management is a significant challenge, particularly during cold start, extended idle, urban driving, and vehicle operation in cold ambient conditions. CDA results in airflow reductions at low loads. Airflow reductions generally result in higher exhaust gas temperatures and lower exhaust flow rates, which are beneficial for maintaining already elevated component temperatures. Airflow reductions also reduce pumping work, which improves fuel efficiency.

The demand for improving fuel economy in passenger cars is continuously increasing. Eliminating energy losses within the engine is one method of achieving fuel economy improvement. Frictional energy losses account for a noticeable portion of the overall efficiency of an engine. Valvetrain friction, specifically at the camshaft interface, is one area where potential for friction reduction is evident. Several factors can impact the friction at the camshaft interface. Some examples include: camshaft lobe profile, rocker arm interface geometry, valve spring properties, material properties, oil temperature, and oil pressure. This paper discusses the results of a series of tests that experimented the changes in friction that take place as these factors are altered. The impact of varying testing conditions such as oil pressure and oil temperature was evaluated throughout the duration of the testing and described herein.

Variable valve actuation is a focus to improve fuel efficiency for passenger car engines. Various means to implement early and late intake valve closing (E/LIVC) at lower load operating conditions is investigated. The study uses GT Power to simulate on E/LIVC on a 2.5 L gasoline engine, in-line four cylinder, four valve per cylinder engine to evaluate different ways to achieve Atkinson cycle performance. EIVC and LIVC are proven methods to reduce the compression-to-expansion ratio of the engine at part load and medium load operation. Among the LIVC strategies, two non-traditional intake valve lift profiles are investigated to understand their impact on reduction of fuel consumption at low engine loads. Both the non-traditional lift profiles retain the same maximum lift as a normal intake valve profile (Otto-cycle) unlike a traditional LIVC profile (Atkinson cycle) which needs higher maximum lift.

Commercial vehicles require continual improvements in order to meet fuel emission standards, improve diesel aftertreatment system performance and optimize vehicle fuel economy. Aftertreatment systems, used to remove engine NOx, are temperature dependent. Variable valve actuation in the form of cylinder deactivation (CDA) has been shown to manage exhaust temperatures to the aftertreatment system during low load operation (i.e., under 3-4 bar BMEP). During cylinder deactivation mode, a diesel engine can have higher vibration levels when compared to normal six cylinder operation. The viability of CDA needs to be implemented in a way to manage noise, vibration and harshness (NVH) within acceptable ranges for today’s commercial vehicles and drivelines. A heavy duty diesel engine (inline 6 cylinder) was instrumented to collect vibration data in a dynamometer test cell.

Increased demands for reduction of fuel consumption and CO2 emissions are driven by the global warming. To meet these challenges with respect to the passenger car segment the strategy of utilizing IC-engine downsizing has shown to be effective. In order to additionally meet requirements for high power and torque output supercharging is required. This can be realized using e.g. turbo-chargers, roots blowers or a combination of several such devices for the highest specific power segment. Both turbo-chargers and roots blowers can be strong sources of sound depending on the operating conditions and extensive NVH abatements such as resonators and encapsulation might be required to achieve superior vehicle NVH. For an efficient resonator tuning process in-duct acoustic source data is required. No published studies exists that describe how the gas exchange process for roots blowers can be described by acoustic sources in the frequency domain.

Functionally graded materials enable structures to have distribution of different properties (physical, thermal, electrical, mechanical, etc.) across its volume; achievable via material/ design/ process engineering. These functionally graded materials can find an application in systems which demand localized variation or enhancement in properties in different regions of the same component. In this paper, we focus on the potential ways of designing functionally graded polymer composite structure by injection molding process. Advanced mold designs for injection molding process can be effectively used to manufacture the functionally graded structures. Innovative design approach has been explored to control the distribution of the filler content /orientation to impart distinctive properties across the cross section / geometry without affecting the bulk properties.

Current Diesel engines development is facing challenging vibro-acoustic requirements and at the same time is struggling with the need to reduce as much as possible the cost and the weight of the engine. The latter obviously has become a key player for fuel consumption reduction. Large covers are commonly used in the base engine design and their noise contribution to total radiated noise is not negligible. Typical covers architecture shows thick cast and ribbed plates, meaning heavy and expensive covers. An interesting option is represented by using thin stamped covers either in aluminum or in steel, that have to show a low vibrational response. The current paper focuses on the structural optimization of such a peculiar design, trying to mitigate as much as possible its noise radiation with the intent to avoid any additional acoustic enabler (e.g. wrapping by means of acoustic foams) that will increase the final cost of the component.

Light weight structures give significant advantages to products in the Industrial sector. Component weight-saving plays a major role in improving the efficiency and performance of assembled systems. The introduction of lighter materials into products using dissimilar material joining techniques can create more weight savings and leads to lighter structures. Structural optimization is another method to optimize the material layout without affecting overall performance of the product. This paper discusses the methods to create lighter structures by the introduction of lighter materials in structures and structural optimization methods. Lighter materials are introduced in the structure using dissimilar material joining techniques. Joining processes such as thermal shrink-fit and mechanical press-fit are useful for metal to metal components. Similarly, adhesively bonded joints are useful for both metal and non-metal (plastics and composites) components.

In amorphous solids such as fused quartz, the failure mechanism under cyclic loading is very different when compared to metals where this failure is attributable to dislocation movement and eventual slip band activity. Standard mechanical fatigue prediction methodologies, S-N or ε-N based, which have been historically developed for metals are rendered inapplicable for this class of material. The fatigue strength of Fused Silica or Fused Quartz (SiO2) material is known to be highly dependent on the stressed area and the surface finish. Stable crack growth in Region II of the V-K curve (Crack growth rate vs Stress intensity factor) is dependent on the competing and transitional effects of temperature and humidity, along that specific section of the stress intensity factor abscissa. Fused glass (under harsh environment conditions) finds usage in Automotive, Marine and Aerospace applications, where stress and load (both static and cyclic) can be severe.

The three parameter Ramberg-Osgood (RO) method finds popular usage for extracting complete stress-strain curve from limited data which is usually available. The currently popular practice of assuming the plasticity to set in only at the Yield point provides computational advantage by separating the complete nonlinear curve, obtained from RO method, into elastic and plastic regions. It is shown, with an example problem, that serious errors are committed by using this method if one compares the obtained results with results of complete stress-strain curve. In the present work we propose a simple Taylor series based approach based on RO method to overcome the above deficiency. This method is found to be computationally efficient. The proposed method is applicable for stress-strain curves of materials for which RO method provides a good approximation.

Fuel economy is one of the major challenges for both on and off-road vehicles. Inefficient engine operation and loss of kinetic energy in the form of heat during braking are two of the major sources of wasted fuel energy. Rising energy costs, stringent emission norms and increased environmental awareness demand efficient drivetrain designs for the next generation of vehicles. This paper analyzes three different types of powertrain concepts for efficient operation of a forklift truck. Starting from a conventional torque convertor transmission, hydrostatic transmission and a hydraulic hybrid transmission (Eaton architecture) are compared for their fuel economy performance. Eaton hydraulic hybrid system is seen to perform much better compared to other two architectures. Improved fuel economy is attributed to efficient engine operation and regeneration of vehicle kinetic energy during braking.

The effects of secondary air on the exhaust oxidation of particulate matters (PM) have been assessed in a direct-injection-spark-ignition engine under fuel rich fast idle condition (1200 rpm; 2 bar NIMEP). Substantial oxidation of the unburned feed gas species (CO and HC) and significant reduction of both the particulate number (up to ∼80%) and volume (up to ∼90%) have been observed. The PM oxidation is attributed to the reactions between the PM and the radicals generated in the oxidation of the feed gas unburned species. This hypothesis is supported by the observation that the reduction in PM volume is proportional to the amount of heat release in the secondary oxidation.

Global vehicle emissions reduction initiatives have warranted the development and usage of new materials and processes not traditionally used in the automotive industry besides exclusive applications. To support this mandate, vehicle lightweighting via metal replacement and design optimization has come into sharp focus as a doubly rewarding effect; namely, a lighter vehicle system not only requires less road load power for motivation, but also allows for smaller, usually more efficient powertrain options, which tend to be more efficient still. The automotive industry has begun to embrace adapting composite materials that have typically been available only to the upper end of the market and specialty racing applications. The specific component detailed in this paper highlights the challenges and rewards for metal replacement with an injection molded, fiber reinforced plastic for usage in mass produced drivetrain systems, namely the Electronic Limited Slip Differential (eLSD).

The combustion of highly boosted gasoline engines is limited by knocking combustion and pre-ignition. Therefore, a comprehensive modelling approach consisting of cycle-to-cycle simulation, reactor modelling with detailed chemistry and CFD-simulation was used to predict the knock initiation and to identify the source of pre-ignition. A 4-cylinder DISI test engine was set up and operated at low engine speeds and high boost pressures in order to verify the accuracy of the numerical approach. The investigations showed that there is a correlation between the knocking combustion and the very first combustion phase. The onset of knock was simulated with a stochastic reactor model and detailed chemistry. In parallel, measurements with an optical spark plug were carried out in order to identify the location of knock onset. The simulation results were in good agreement with the measurements. Deposits and oil/fuel-droplets are possible triggers of pre-ignition.

Carbon, hydrogen and oxygen are major elements in vehicle fuels. Knowledge of fuels elemental composition is helpful in addressing its performance characteristics. Carbon, hydrogen and oxygen composition is an important parameter in engine calibration affecting vehicle performance, emissions and fuel economy. Biodiesel, a fuel comprised of mono-alkyl esters of long-chain fatty acids also known as Fatty Acid Methyl Esters(FAME), derived from vegetable oils or animal fats, has become an important commercial marketplace automotive fuel in the United States (US) and around the world over last few years. FAME biodiesels have many chemical and physical property differences compared to conventional petroleum based diesel fuels. Also, the properties of biodiesel vary based on the feedstock chosen for biodiesel production. One of the key differences between petroleum diesel fuels and biodiesel is the oxygen content.

An advanced variable valve actuation system is developed that requires a coating with high stress loading capability on the sliding interfaces to enable compact packaging solutions for gasoline passenger car applications. The valvetrain system consists of a switching roller bearing finger follower (SRFF) combined with a dual feed hydraulic lash adjuster and an oil control valve. The SRFF contains two slider pads and a single roller to provide discrete variable valve lift capability on the intake valves. These components are installed on a four cylinder gasoline engine. The motivation for designing this type of variable valve actuation system is targeted to improve fuel economy by reducing the air pumping losses during partial load engine operation. This paper addresses the technology developed to utilize a Diamond-like carbon (DLC) coating on the slider pads of the SRFF.

Global environmental and economic concerns regarding increasing fuel consumption and greenhouse gas emission are driving changes to legislative regulations and consumer demand. As regulations become more stringent, advanced engine technologies must be developed and implemented to realize desired benefits. Discrete variable valve lift technology is a targeted means to achieve improved fuel economy in gasoline engines. By limiting intake air flow with an engine valve, as opposed to standard throttling, road-load pumping losses are reduced resulting in improved fuel economy. This paper focuses on the design and development of a switching roller finger follower system which enables two mode discrete variable valve lift on end pivot roller finger follower valvetrains. The system configuration presented includes a four-cylinder passenger car engine with an electro-hydraulic oil control valve, dual feed hydraulic lash adjuster, and switching roller finger follower.