Search Results

A thermal model is presented which can be utilized to estimate the resulting temperatures in the components of a PMSM for different operation points and duty cycles. Different model types have been reviewed initially and the presented thermal model is realized in the form of a Lumped Parameter Thermal Model (LPTM). This model type was identified to be the best option for temperature estimations in the early design phase of electric motors. The presented model is designed flexibly, so that it can be used for the evaluation of various cooling system modifications such as different materials or changed temperature limits. For proving its suitability, the model is used herein for a comparison of two cooling systems for electric motors: frame cooling and direct winding cooling. Both systems can be equipped with a supplementary rotor cooling.

The transition towards sustainable mobility encourages research into biofuels for use in internal combustion engines. For these alternative energy carriers, high-fidelity experimental data of flame speeds influenced by pressure, temperature, and air-fuel equivalence ratio under engine-relevant conditions are required to support the development of robust combustion models for spark-ignition engines. E.g., physicochemical-based approximation formulas adjusted to the fuel provide similar accuracy as high fidelity chemical kinetic model calculations at a fraction of the computational cost and can be easily adopted in engine simulation codes. In the present study, a workflow to enable predictive combustion engine modeling is applied first for a gasoline reference fuel and two biofuel blends recently proposed by Dahmen and Marquardt [Energy Fuels, 2017].

Oxygenated fuels such as polyoxymethylene dimethyl ethers (OME) offer a chance to significantly decrease emissions while switching to renewable fuels. However, compared to conventional diesel fuel, they have lower heating values and different evaporation behaviors which lead to differences in spray, mixture formation as well as ignition delay. In order to determine the mixture formation characteristics and the combustion behavior of neat OME3-5, optical investigations have been carried out in a high-pressure-chamber using shadowgraphy, mie-scatterlight and OH-radiation recordings. Liquid penetration length, gaseous penetration length, lift off length, spray cone angle and ignition delay have been determined and compared to those measured with diesel-fuel over a variety of pressures, temperatures, rail pressures and injection durations.

In the foreseeable future, the transportation sector will continue to rely on internal combustion engines. Therefore, reduction of engine-out emissions and increase in engine efficiency are important goals to meet future legislative regulations and restricted fuel resources. One viable option, which provides lower peak temperatures and increased mixture homogeneity and thus simultaneously reduces nitric oxide as well as soot, is a low-temperature combustion (LTC) concept. However, this might result in an increase of unburnt hydrocarbon, carbon monoxide, and combustion noise due to early combustion phasing and lower engine efficiency. Various studies show that these drawbacks can be compensated by advanced injection strategies, e.g. by employing multiple injections. The aim of this work is to identify the optimum injection strategy, which enables a wide range of engine operating points in LTC mode with reduced engine-out emissions.

Ensuring software quality is one of the key challenges associated with the development of automotive embedded systems. Software architecture plays a pivotal role in realizing functional and non-functional requirements for automotive embedded systems. Software architecture is a work-product of the early stages of software development. The design errors introduced at the early stages of development will increase cost of rework. Hence, an early evaluation of software architecture is important. PERSIST (Powertrain control architecture Enabling Reusable Software development for Intelligent System Tailoring) is a model-based software product line approach which focuses on cross-project standardization of powertrain software. The product line is characterized by common design guidelines and adherence to industry standards like ISO 25010, AUTOSAR and ISO 26262.

Powertrain software development for series production faces multifaceted challenges related to high functional complexity, high quality standards, reduced time to market and high development costs. Software architecture tackles the above mentioned challenges by breaking down the complexity of application software into modular components. Hence, design errors introduced during that phase cause significant cost and time deviations. Early and repeated analysis of new and modified architecture artifacts is required to detect design errors and the impact of the subsequent changes in the software architecture. Engine management software has a high degree of functional complexity and large number of system variants depending upon market requirements. This paper deals with the methods to perform automated evaluation of Renault’s EMS 2012 Engine Management Software in a Continuous Integration Framework.

A new index to evaluate the inherent soot reduction in a diesel-like spray plume is proposed in this study. The index is named “Oxidation Potential Number” and was derived with the help of a computational fluid dynamics (CFD) software. C8 - C16 n-alkanes, 1-alcohols and di-n-ethers were studied with the help of this index over four part load engine operating conditions, representative of a C-class diesel vehicle. The CFD modelling results have shown that C8 molecules feature a higher potentiality to reduce the soot. Thus, C8 molecules were tested in a single cylinder diesel engine over the same operating conditions. In conclusion, the proposed index is compared with the soot engine out emission.

2-Butanone (C4H8O) is a promising alternative fuel candidate as a pure as well as a blend component for substitution in standard gasoline fuels. It can be produced by the dehydrogenation of 2-butanol. To describe 2-butanone's basic combustion behaviour, it is important to investigate key physical properties such as the laminar burning velocity. The laminar burning velocity serves on the one hand side as a parameter to validate detailed chemical kinetic models. On the other hand, especially for engine simulations, various combustion models have been introduced, which rely on the laminar burning velocity as the physical quantity describing the progress of chemical reactions, diffusion, and heat conduction. Hence, well validated models for the prediction of laminar burning velocities are needed. New experimental laminar burning velocity data, acquired in a high pressure spherical combustion vessel, are presented for 1 atm and 5 bar at temperatures of 373 K and 423 K.

Maintaining low NOx emissions over the operating range of diesel engines continues to be a major issue. However, optical measurements of nitric oxide (NO) are lacking particularly in the core of diesel jets, i.e. in the region of premixed combustion close to the spray axis. This is basically caused by severe attenuation of both the laser light and fluorescent emission in laser-induced fluorescence (LIF) applications. Light extinction is reduced by keeping absorption path lengths relatively short in this work, by investigating diesel jets in a combustion vessel instead of an engine. Furthermore, the NO-detection threshold is improved by conducting 1-d line measurements instead of 2-d imaging. The NO-LIF data are corrected for light attenuation by combined LIF and spontaneous Raman scattering. The quantified maximum light attenuation is significantly lower than in comparable previous works, and its wavelength dependence is surprisingly weak.

With increasing interest in new biofuel candidates, 1-octanol and di-n-butylether (DNBE) were presented in recent studies. Although these molecular species are isomers, their properties are substantially different. In contrast to DNBE, 1-octanol is almost a gasoline-type fuel in terms of its auto-ignition quality. Thus, there are problems associated with engine start-up for neat 1-octanol. In order to find a suitable glow-plug position, mixture formation is studied in the cylinder under almost idle operating conditions in the present work. This is conducted by planar laser-induced fluorescence in a high-speed direct-injection optical diesel engine. The investigated C8-oxygenates are also significantly different in terms of their evaporation characteristics. Thus, in-cylinder mixture formation of these two species is compared in this work, allowing conclusions on combustion behavior and exhaust emissions.

The original Equation 3 found at the bottom of page 64 was erroneous.

Pilot injection (PI) during the negative-valve-overlap (NVO) period is one method to improve control of combustion in gasoline controlled auto-ignition engines. This is generally attributed to both chemical and thermal effects. However, there are little experimental data on active species formed by the combusting PI and their effect on main combustion in real engines. Thus, it is the objective of the current study to apply and assess optical in-cylinder diagnostics for these species. Firstly, the occurrence and nature of combustion during the NVO period is investigated by spectrally-resolved multi-species flame luminescence measurements. OH*, CH*, HCO*, CO-continuum chemiluminescence, and soot luminosity are recorded. Secondly, spectrally-, spatially-, and cycle-resolved laser-induced fluorescence measurements of formaldehyde are conducted. It is attempted to find a cycle-resolved measure of the chemical effect of PI.

Future engines and vehicles will be required to reduce both regulated and CO2 emissions. To achieve this performance, they will be configured with advanced hardware and engine control technology that will enable their operation on a broader range of fuel properties than today. Previous work has shown that an advanced compression ignition bench engine can operate successfully on a European market gasoline over a range of speed/load conditions while achieving diesel-like engine efficiency and acceptable regulated emissions and noise levels. Stable Gasoline CI (GCI) combustion using a European market gasoline was achieved at high to medium engine loads but combustion at lower loads was very sensitive to EGR rates, leading to longer ignition delays and a steep cylinder pressure rise.

It is well known that an unplanned component mass increase during vehicle design creates a ripple effect of changes throughout the vehicle subsystems, which require resizing for the additional mass. This in turn, increases overall vehicle mass. And the opposite is true in vehicle mass reduction where subsystem resizing is necessary to account for an initial mass reduction enabled, for example, by a new technology. These secondary mass changes can be significant and must be considered in the mass budgeting process due to their importance to fuel consumption and greenhouse gas emission assessments. Secondary mass reduction may be modeled using subsystem mass influence coefficients-the incremental change in subsystem mass for a unit change in gross vehicle mass. This paper focuses on means to estimate influence coefficients using two methods: Analytical and Regression.

Current production of Dual Clutch Transmissions (DCTs) feature a maximum of seven speeds, which can easily be realized using three main shafts and four shift sleeves. To increase the number of gears with conventional means, more gears, shift sleeves and shafts have to be added thus increasing size, weight and cost. With the “xDCT” family, FEV has developed a series of DCT concepts which effectively minimize mechanical complexity for any given number of gears by combining two innovative ideas: “Gear generation” and “supported shifts”. In order to “generate gears”, a switchable connection between the two input shafts is installed which allows to use all gears inside the transmission with both clutches. The main challenge then is to effectively use the large number of resulting gears in a shift schedule without torque interruption. The solution is to incorporate “supported shifts” during which torque fill-in for an AMT-style gear shift is provided by the next higher gear.

Besides an excellent driving performance and power output the reduction of CO2 emission is one of the main driver for the increasing distribution of modern diesel engines. Downsizing/downspeeding, friction reduction, new combustion processes and light weight engine architecture describe additional improvement potentials. Nevertheless, these development trends have a significant influence on the noise and vibration behavior of diesel engines. Therefore measures are also necessary to compensate these acoustic disadvantages. Within this publication the most important and efficient countermeasures are described and assessed. Combustion is still one of the dominant noise sources of a modern diesel engine. Diesel knocking is annoying and the combustion noise level is typically higher than for gasoline engines.

It is the objective of this work to characterize mixture formation in the sprays emanating from Multi-Layer (ML) nozzles under approximately engine-like conditions by quantitative, spatially, and temporally resolved fuel-air ratio and temperature measurements. ML nozzles are cluster nozzles which have more than one circle of orifices. They were introduced previously, in order to overcome the limitations of conventional nozzles. In particular, the ML design yields the potential of variable spray interaction, so that mixture formation could be controlled according to the operating condition. In general, it was also a primary aim of the cluster-nozzle concepts to combine the enhanced atomization and pre-mixing of small nozzle holes with the longer spray penetration lengths of large holes. The applied diagnostic, which is based on 1d spontaneous Raman scattering, yields the quantitative stoichiometric ratio and the temperature in the vapor phase.

Both, the continuous strengthening of the exhaust emission legislation and the striving for a substantial reduction of carbon dioxide output in the traffic sector depict substantial requirements for the development of future diesel engines. These engines will comprise not only the mandatory diesel oxidation catalyst (DOC) and particulate filter DPF but a NOx aftertreatment system as well - at least for heavier vehicles. The oxidation catalysts as well as currently available NOx aftertreatment technologies, i.e., LNT and SCR, rely on sufficient exhaust gas temperatures to achieve a proper conversion. This is getting more and more critical due to the fact that today's and future measures for CO₂ reduction will result in further decrease of engine-out temperatures. Additionally this development has to be considered in the light of further engine electrification and hybridization scenarios.

Both, the continuous strengthening of the exhaust emission legislation and the striving for a substantial reduction of the carbon dioxide output in the traffic sector depict substantial requirements for the global automotive industry and especially for the engine manufacturers. From the multiplicity of possible approaches and strategies for clear compliance with these demands, engine internal measures offer a large and, eventually more important, very economical potential. For example, the achievements in fuel injection technology are a measure which in the last years has contributed significantly to a notable reduction of the emissions of the modern DI Diesel engines at favorable fuel efficiency. Besides the application of modern fuel injection technology, the linked combustion control (Closed Loop Combustion Control) opens possibilities for a further optimization of the combustion process.

Piston rings are faced with a broad range of demands like optimal sealing properties, wear properties and reliability. Even more challenging boundary conditions must be met when latest developments in the fields of direct injection as well as the application of bio fuels. This complex variety of piston ring design requirements leads to the need of a comprehensive simulation model in order to support the development in the early design phase prior to testing. The simulation model must be able to provide classical objectives like friction analysis, wear rate and blow-by. Furthermore, it must include an adequate oil consumption model. The objective of this work is to provide such a simulation model that is embedded in the commercial MBS software ‘FEV Virtual Engine’. The MBS model consists of a cranktrain assembly with a rigid piston that contains flexible piston rings.