Search Results

Design, testing, and implementation of new aftertreatment devices under various engine operating conditions is necessary to meet increasingly stringent regulatory mandates. One common aftertreatment device, the catalytic converter, is typically developed at a reduced scale and tested using predefined fluid compositions sourced from bottle gases and can undergo both species and temperature cycling in addition to steady-state testing. However, these bench-top conditions may differ from real-world operation in terms of flow-rates, species composition, and temperatures experienced. Transitioning from small-scale bench-top testing to full-scale engine applications requires larger monoliths that therefore have a significant amount of catalyst slurry to be washcoated, which increases cost and fabrication time.

With reference to present literature, most OEMs are working on reducing product development time by around ~20%, through seamless integration of digital ecosystem and focusing on dynamic customer needs. The Systems Engineering approach focuses on functions & systems rather than components. In this approach, designers (Computer Aided Design) / analysts (Computer Aided Engineering) need to understand program requirements early to enable seamless integration. This approach also reduces the number of iterative loops between cross functions thereby reducing the development cycle time. In this paper, we have attempted to tackle a common challenge faced by Closures (Liftgate) engineering: meeting slam durability fatigue life while replicating customer normal and abusive closing behavior.

An analytical mechanics model was employed to predict the delamination of several thermal-barrier-coated pistons that had been previously tested in a high-output, single-cylinder diesel engine. Some of the coatings delaminated during engine operation. Results are presented for two thicknesses of the same coating material, and for two similar coatings with different levels of stiffness. All the coating thermomechanical properties such as thermal conductivity, density, volumetric heat capacity, thickness, elastic modulus, coefficient of thermal expansion, Poisson ratio and toughness, were measured prior to engine testing. Previous measurements of the piston transient heat flux, based on fast-response surface temperature data, in the same engine were used as an input to calculate the multilayer wall temperature distribution. A theoretical methodology was employed to evaluate and predict the coating durability.

A closed-cycle computational model of a non-Wankel rotary engine was thoroughly investigated to achieve optimal efficiencies, in a multitude of loading conditions relevant to automotive and aeronautical applications. Computational fluid dynamics (CFD) modeling was conducted in CONVERGE CFD, targeting the operation of a single pre-chamber and downstream main chamber engine system, roughly from 100 crank angle degrees (CAD) before top dead center (bTDC) to 100 CAD after top dead center (aTDC). In the developed framework, optimization studies involved main decision variables, including the engine’s compression ratio (CR), the injector’s position within the pre-chamber, the injector’s nozzle hole count and nozzle hole diameters. Traditional and split-injection strategies for the introduction of diesel fuel into the pre-chamber were evaluated by varying spray-related parameters including total injected mass, injection pressure, start of injection(s), and injection duration(s).

Many efforts have been made in recent years to find renewable replacements for fossil fuels that can reduce the carbon footprint without compromising combustion performance. Bio-blendstock oil developed from woody biomass using a reliable thermochemical conversion method known as catalytic fast pyrolysis (CFP), along with hydrotreating upgrading has the potential to deliver on this renewable promise. To further our understanding of naphthenic-rich bio-blendstock oils, an improved formulation surrogate fuel (SF), SF1.01, featuring decalin and butylcyclohexane naphthenic content was devised and blended with research-grade No.2 diesel (DF2) at various volume percentages. The blends were experimentally evaluated in a single-cylinder Ricardo Hydra compression ignition engine to quantify engine and emissions performance of SF1.01/DF2 blends. Injection timing events were varied from knock limit to misfire limit at the same operating conditions for all blends.

Hybridizing Solid Oxide Fuel Cells (SOFCs) with internal combustion engines is an attractive solution for power generation at high electrical conversion efficiency while emitting significantly reduced emissions than conventional fossil fueled plants. The gas that exits the anode of an SOFC operating on natural gas is a mixture of H2, CO, CO2, and H2O vapor, which are the products of the fuel reforming and the electrochemical process in the stack. In this study, experiments were conducted on a single-cylinder, spark-ignited Cooperative Fuel Research Engine using the anode off-gas as the fuel, at compression ratio of 11:1 and 13:1, engine speed of 1200 rev/min and intake pressure of 75 kPa, to investigate the combustion characteristics and emissions formation. A comparison was drawn with combustion with Compressed Natural Gas (CNG) at the same engine operating conditions.

An experimental study was conducted on a Ricardo Hydra single-cylinder light-duty diesel research engine. Start of Injection (SOI) timing sweeps from -350 deg aTDC to -210 deg aTDC were performed on a total number of five pistons including two baseline metal pistons and three coated pistons to investigate the effects of thick thermal barrier coatings (TBCs) on the efficiency and emissions of low-temperature combustion (LTC). A fuel with a high latent heat of vaporization, wet ethanol, was chosen to eliminate the undesired effects of thick TBCs on volumetric efficiency. Additionally, the higher surface temperatures of the TBCs can be used to help vaporize the high heat of vaporization fuel and avoid excessive wall wetting. A specialized injector with a 60° included angle was used to target the fuel spray at the surface of the coated piston.

Homogeneous Charge Compression Ignition (HCCI) enables combustion with high efficiency and low emissions. Control over the combustion process and its narrow operating range are still the biggest challenges associated with HCCI. To expand the operable load ranges of HCCI, this paper explores the effects of single versus two-stage ignition fuels by studying the Primary Reference Fuels (PRF) in a variable compression ratio Cooperative Fuel Research (CFR) engine. The PRF fuels, iso-octane and n-heptane, are blended together at various concentrations to create fuel blends with different autoignition characteristics. Experiments were conducted using these PRF blends to explore the extent to which the load range can be extended with two-stage ignition fuels at various compression ratios and intake temperatures. The reactivity of the PRF blends increases with the fraction of n-heptane and so does the amount of low temperature heat release (LTHR).

Homogeneous Charge Compression Ignition (HCCI) is a combustion concept with the potential for future clean and efficient automotive powertrains. In HCCI, the thermal stratification has been proven to play an important role in dictating the combustion process, mainly caused by heat transfer to the wall during compression. In this study, a multi-zone, control-mass model with thermal stratification and chemical kinetics was developed to simulate HCCI combustion. In this kind of model, the initial conditions and the zonal heat transfer fraction distribution are critical for the modeling accuracy and usually require case-by-case tuning. Instead, in this study, the Thermal Stratification Analysis (TSA) methodology is used to generate the zonal heat transfer fraction distribution from experimental HCCI data collected on a fired, metal engine.

Thermally Stratified Compressions Ignition (TSCI) is a new advanced, low temperature combustion concept that aims to control the thermal stratification in the cylinder in order to control the heat release process in a lean, compression-ignition combustion mode. This work uses “wet ethanol”, a mixture of 80% ethanol and 20% water by mass, to increase thermal stratification beyond what naturally occurs, via evaporative cooling of a split direct injection. TSCI with wet ethanol has previously shown the potential to increase the high-load limit when compared to HCCI. The experiments conducted in this paper aim to fundamentally understand the effect that injection strategy has on the heat release process in TSCI. TSCI employs a split-injection strategy in which an injection during the intake stroke allows the majority of the fuel to premix with the air and an injection during the compression stroke introduces the desired level of thermal stratification to control the heat release rate.

This article investigates the effects of various primary reference fuel (PRF) blends, compression ratios, and intake temperatures on the thermodynamics and performance of homogeneous charge compression ignition (HCCI) combustion in a Cooperative Fuels Research (CFR) engine. Combustion phasing was kept constant at a CA50 phasing of 5° after top dead center (aTDC) and the equivalence ratio was kept constant at 0.3. Meanwhile, the compression ratio varied from 8:1 to 15:1 as the PRF blends ranged from pure n-heptane to nearly pure isooctane. The intake temperature was used to match CA50 phasing. In addition to the experimental results, a GT-Power model was constructed to simulate the experimental engine and the model was validated against the experimental data. The GT-Power model and simulation results were used to help analyze the energy flows and thermodynamic conditions tested in the experiment.

The operating range of Homogeneous Charge Compression Ignition (HCCI) engines is limited to low and medium loads by high heat release rates. Negative Valve Overlap (NVO) can be used to facilitate ignition of high octane number fuels and control pressure rise rates by diluting the mixture with hot residual gas and introducing some thermal stratification. Controlling the thermal stratification results in sequential autoignition, reduced heat release rates, and operating range extension. Therefore, fundamental understanding of thermal stratification in HCCI combustion with high levels of internal residuals is necessary, along with the development of appropriate models to simulate thermal stratification and its effects on HCCI combustion. A 3-D Computational Fluid Dynamics (CFD) model of a 2.0 L GM Ecotec engine (LNF type) engine cylinder, modified for HCCI combustion, was developed using CONVERGE CFD.

A CFD investigation has been conducted to study the efficiency and emissions characteristics of Thermally Stratified Compression Ignition (TSCI) combustion with direct water injection. The motivation for using this new low temperature combustion mode is its ability to control the heat release process by introducing a forced and controlled thermal stratification beyond what would occur naturally. In this case, TSCI is enabled using direct water injection. The added degree of control over the combustion process allows for a significantly broader operable load range compared to HCCI. The effects of injection parameters including the pressure, start of injection (SOI) timing, and spray pattern have been shown previously to affect the heat release of TSCI and its induced thermal stratification. In the present work, the efficiency and emissions considerations were investigated in detail, and the effects of injected mass are presented.

The die wear up to 80,800 hits on a prog-die setup for bare DP1180 steel was investigated in real production condition. In total, 31 die inserts with the combination of 11 die materials and 9 coatings were evaluated. The analytical results of die service life for each insert were provided by examining the evolution of surface wear on inserts and formed parts. The moments of appearance of die defects, propagation of die defects, and catastrophic failure were determined. Moreover, the surface roughness of the formed parts for each die insert was characterized using Wyko NT110 machine. The objectives of the current study are to evaluate the die durability of various tooling materials and coatings for flange operations on bare DP 1180 steel and update OEM tooling standards based on the experimental results. The current study provides the guidance for the die material and coating selections in large volume production for next generation AHSSs.

Engine acoustics measured by microphones near the engine have been used in controlled laboratory settings for combustion feedback and even combustion phasing control, but the use of these techniques in a vehicle where many other noise sources exist is problematic. In this study, surface-mounted acoustic emissions sensors are embedded in the block of a 2.0L turbocharged GDI engine, and the signal is analyzed to identify useful feedback features. The use of acoustic emissions sensors, which have a very high frequency response and are commonly used for detecting material failures for health monitoring, including detecting gear pitting and ring scuffing on test stands, enables detection of acoustics both within the range of human hearing and in the ultrasonic spectrum. The high-speed acoustic time-domain data are synchronized with the crank-angle-domain combustion data to investigate the acoustic emissions response caused by various engine events.

A pilot-main injection strategy is investigated for a part-load operating point in a single cylinder optical Diesel engine. As the energizing dwell between the pilot and main injections decreases below 200 μs, combustion noise reaches a minimum and a reduction of 3 dB is possible. This decrease in combustion noise is achieved without increased pollutant emissions. Injection schedules employed in the engine are analyzed with an injection analyzer to provide injection rates for each dwell tested. Two distinct injection events are observed even at the shortest dwell tested; rate shaping of the main injection occurs as the dwell is adjusted. High-speed elastic scattering imaging of liquid fuel is performed in the engine to examine initial liquid penetration rates.

General Motors has developed an all-new Ecotec 1.5 L range extender engine for use in the 2016 next generation Voltec propulsion system. This engine is part of a new Ecotec family of small displacement gasoline engines introduced in the 2015 model year. Major enhancements over the range extender engine in the current generation Voltec propulsion system include the adoption of direct injection (DI), cooled external exhaust gas recirculation (EGR), and a high 12.5:1 geometric compression ratio (CR). Additional enhancements include the adoption of high-authority phasers on both the intake and exhaust camshafts, and an integrated exhaust manifold (IEM). The combination of DI with cooled EGR has enabled significant thermal efficiency gains over the 1.4 L range extender engine in the current generation Voltec propulsion system at high engine loads.

The introduction of new safety critical features using software-intensive systems presents a growing challenge to hazard analysis and requirements development. These systems are rich in feature content and can interact with other vehicle systems in complex ways, making the early development of proper requirements critical. Catching potential problems as early as possible is essential because the cost increases exponentially the longer problems remain undetected. However, in practice these problems are often subtle and can remain undetected until integration, testing, production, or even later, when the cost of fixing them is the highest. In this paper, a new technique is demonstrated to perform a hazard analysis in parallel with system and requirements development. The proposed model-based technique begins during early development when design uncertainty is highest and is refined iteratively as development progresses to drive the requirements and necessary design features.

This paper presents the implementation of an off-line optimized torque vectoring controller on an electric-drive vehicle with four in-wheel motors for driver assistance and handling performance enhancement. The controller takes vehicle longitudinal, lateral, and yaw acceleration signals as feedback using the concept of state-derivative feedback control. The objective of the controller is to optimally control the vehicle motion according to the driver commands. Reference signals are first calculated using a driver command interpreter to accurately interpret what the driver intends for the vehicle motion. The controller then adjusts the braking/throttle outputs based on discrepancy between the vehicle response and the interpreter command.

To investigate the effect of aeration on fluid-elastomer compatibility, 4 types of elastomers were aged in three gear lubes. The four types of elastomers include a production fluorinated rubber (FKM) and production hydrogenated nitrile rubber (HNBR) mixed by the part fabricator, a standard low temperature flexible fluorinated rubber (FKM, ES-4) and a standard ethylene-acrylic copolymer (AEM, ES-7) mixed by SAE J2643 approved rubber mixer. The three gear lubes are Fluid a, Fluid b and Fluid c, where Fluid b is a modified Fluid with additional friction modifier, and Fluid c is friction modified chemistry from a different additive supplier. The aeration effect tests were performed at 125°C for 504 hours. The aerated fluid aging test was performed by introducing air into fluid aging tubes as described in General Motors Company Materials Specification GMW16445, Appendix B, side-by-side with a standard ASTM D471 test.