Search Results

Brake pad to rotor adhesion following exposure to corrosive environments, commonly referred to as “stiction”, continues to present braking engineers with challenges in predicting issues in early phases of development and in resolution once the condition has been identified. The goal of this study took on two parts - first to explore trends in field stiction data and how testing methods can be adapted to better replicate the vehicle issue at the component level, and second to explore the impacts of various brake pad physical properties variation on stiction propensity via a controlled design of experiments. Part one will involve comparison of various production hardware configurations on component level stiction tests with different levels of prior braking experience to evaluate conditioning effects on stiction breakaway force.

The strong focus on reducing brake drag, driven by a historic ramp-up in global fuel economy and carbon emissions standards, has led to renewed research on brake caliper drag behaviors and how to measure them. However, with the increased knowledge of the range of drag behaviors that a caliper can exhibit comes a particularly vexing problem - how should this complex range of behaviors be represented in the overall road load of the vehicle? What conditions are encountered during coastdown and fuel economy testing, and how should brake drag be measured and represented in these conditions? With the Environmental Protection Agency (amongst other regulating agencies around the world) conducting audit testing, and the requirement that published road load values be repeatable within a specified range during these audits, the importance of answering these questions accurately is elevated. This paper studies these questions, and even offers methodology for addressing them.

The Chevrolet Volt is an electric vehicle with extended-range that is capable of operation on battery power alone, and on engine power after depletion of the battery charge. First generation Chevrolet Volts were driven over half a billion miles in North America from October 2013 through September 2014, 74% of which were all-electric [1, 12]. For 2016, GM has developed the second-generation of the Volt vehicle and “Voltec” propulsion system. By significantly re-engineering the traction power inverter module (TPIM) for the second-generation Chevrolet Volt extended-range electric vehicle (EREV), we were able to meet all performance targets while maintaining extremely high reliability and environmental robustness. The power switch was re-designed to achieve efficiency targets and meet thermal challenges. A novel cooling approach enables high power density while maintaining a very high overall conversion efficiency.

This paper highlights a simplified CAE model technique, which can simulate and predict door crush strength performance quickly. Such quick models can be used for DFSS and Design change studies. The proposed method suggests an equivalent sub model technique using only the door beam with tuned stiffness end springs to predict FMVSS214S full vehicle crush performance. Such models can be solved in minutes and hence very useful for DFSS studies during product design. The proposed method can be used to finalize door beam design for identical size of vehicle doors to meet required FMVSS214S crush performance. The paper highlights the door beam end springs tuning for identical size of cars and SUVs. Four vehicles were considered for the study. A single spring F-D (force -displacement) is tuned which correlated well for frond door of all the four vehicles. A separate unique spring F-D was needed which correlated well for rear door of all the 4 vehicles.

The Sarbanes-Oxley Act created new standards for corporate accountability pertaining to all publicly-owned and traded firms. It holds top executives accountable for the accuracy of all financial data and statements, including reported tangible assets. It requires existence of auditable internal accounting control measures and specifies adherence to new internal controls and procedures designed to ensure the validity of their financial records and physical assets. The Act presents a challenge to every manufacturing firm to have a low-cost system implemented that can produce an exact physical-asset location, existence, verification and accounting on demand. Clearly, such low-cost solutions for enterprise-wide compliance would also provide verifiable and reliable data for corporate property tax, loan collateral, and audit requirements.

In order to take into account the local material non-linear elastic-plastic effects generated by notches, Glinka proposed the equivalent strain energy density (ESED) Criterion which has been widely accepted and used in fatigue theory and calculation for the last few decades. In this paper, Glinka's criterion is applied to structural optimization design for elastic-plastic correction to consider material non-linear elastic-plastic effects. The equivalent (fictitious) stress was derived from Glinka's Criterion equation for the commonly used Ramberg-Osgood and bi-linear stress and strain relationships. This equivalent stress can be used as the stress boundary constraint threshold in structural optimization design to control the elastic-plastic stress or strain in nonlinear optimization.

An advanced variable valve actuation (VVA) system is characterized following end-of-life testing to enable fuel economy solutions for passenger car applications. The system consists of a switching roller finger follower (SRFF) combined with a dual feed hydraulic lash adjuster and an oil control valve that are integrated into a four cylinder gasoline engine. The SRFF provides discrete valve lift capability on the intake valves. The motivation for designing this type of VVA system is targeted to improve fuel economy by reducing the air pumping losses during part load engine operation. This paper addresses the durability of a SRFF for meeting passenger car durability requirements. Extensive durability tests were conducted for high speed, low speed, switching, and cold start operation. High engine speed test results show stable valvetrain dynamics above 7000 engine rpm. System wear requirements met end-of-life criteria for the switching, sliding, rolling and torsion spring interfaces.

A D.C. permanent magnet motor powered fan can serve as a cooling package air flow meter. This allows for continuous air flow monitoring during vehicle operation with applications to more precise air flow control schemes. In the freewheel mode, the air flow is a linear function of the open circuit voltage of the motor. In the powered mode, the motor voltage and current can be used with a motor and fan model to predict fan air flow. The model is explained and verifying test results are presented. Comparison of the accuracy and complexity vs. that of arrays of precision anemometers is provided.

Magnesium alloy extrusions offer potentially more mass saving compared to magnesium castings. One of the tasks in the United States Automotive Materials Partnership (USAMP) ?Magnesium Front End Research and Development? (MFERD) project is to evaluate magnesium extrusion alloys AM30, AZ31 and AZ61 for automotive body applications. Solid and hollow sections were made by lowcost direct extrusion process. Mechanical properties in tension and compression were tested in extrusion, transverse and 45 degree directions. The tensile properties of the extrusion alloys in the extrusion direction are generally higher than those of conventional die cast alloys. However, significant tension-compression asymmetry and plastic anisotropy need to be understood and captured in the component design.

Based on Woodbury-Sherman-Morrison formula, a general and efficient method for torsional damper tuning is presented. This method is based on exact calculation of the resulting Frequency Response Functions (FRF's) of the system with the damper by using the original (old) FRF's of the original (baseline) system and the damper's parameters (the mass polar moment of inertia, stiffness and damping coefficient). The only requirement for this method is to have the baseline FRF's at the active points of the structure where the damper is to be attached and those point where the resulting FRF's are of interest. The baseline FRF's can be obtained by either analytical or experimental methods. Once this requirement is met, all possible scenarios of the dampers for their potential and feasibility can be efficiently evaluated before being put into service without the need for costly hardware modification and test cycles on actual structure.

Tuned mass dampers (TMDs) or vibration absorbers are widely used in the industry to address various NVH issues, wherein, tactile-vibration or noise mitigation is desired. TMDs can be classified into two categories, namely, tuned-to-resonance and tuned-to-discrete-excitation. An overwhelming majority of TMD applications found in the industry belong to the tuned-to-resonance category, so much of information is available on design considerations of such dampers; however, little is published regarding design considerations of dampers tuned-to-discrete-excitation. During this study, a problem was solved that occurred at a discrete excitation frequency away from the primary resonance frequency of a steering column-wheel assembly. A solution was developed in multiple stages. First the effects of various factors such as mass and damping were analyzed by using a closed-form solution.

Automotive engines are regularly utilized in the material handling market where LPG is often the primary fuel used. When compared to gasoline, the use of gaseous fuels (LPG and CNG) as well as alcohol based fuels, often result in significant increases in valve seat insert (VSI) and valve face wear. This phenomenon is widely recognized and the engine manufacturer is tasked to identify and incorporate appropriate valvetrain material and design features that can meet the ever increasing life expectations of the end-user. Alternate materials are often developed based on laboratory testing – testing that may not represent real world usage. The ultimate goal of the product engineer is to utilize accelerated lab test procedures that can be correlated to field life and field failure mechanisms, and then select appropriate materials/design features that meet the targeted life requirements.

The auto industry has had decades of experience with designing safe vehicles. The introduction of highly integrated features brings new challenges that require innovative adaptations of existing safety methodologies and perhaps even some completely new concepts. In this paper, we describe some of the new challenges that will be faced by all OEMs and suppliers. We also describe a set of generic top-level potential hazards that can be used as a starting point for the Preliminary Hazard Analysis (PHA) of a vehicle software-intensive motion control system. Based on our experience with the safety analysis of a system of this kind, we describe some general categories of hazard causes that are considered for software-intensive systems and can be used systematically in developing the PHA.

This paper presents methods for analyzing and visualizing the relationship between input torque, clutch torque, output torque and input acceleration during the inertia phase of a shift. The methods presented are an expansion of the lever analogy [1]. The methods are useful for understanding how geartrain inertia affects control, both its magnitude and distribution. Clutch energy and shift speeds are also easy to calculate and understand using the tools presented. Lastly the methods show why the optimum control strategies for various transmission configurations (such as DCT's, planetary transmissions, etc.) are different in the inertia phase.

By adapting vehicle control systems to the skill level of the driver, the overall vehicle active safety provided to the driver can be further enhanced for the existing active vehicle controls, such as ABS, Traction Control, Vehicle Stability Enhancement Systems. As a follow-up to the feasibility study in [1], this paper provides some recent results on data-driven driving skill characterization. In particular, the paper presents an enhancement of discriminant features, the comparison of three different learning algorithms for recognizer design, and the performance enhancement with decision fusion. The paper concludes with the discussions of the experimental results and some of the future work.

Model-based design is a collection of practices in which a system model is at the center of the development process, from requirements definition and system design to implementation and testing. This approach provides a number of benefits such as reducing development time and cost, improving product quality, and generating a more reliable final product through the use of computer models for system verification and testing. Model-based design is particularly useful in automotive control applications where ease of calibration and reliability are critical parameters. A novel application of the model-based design approach is demonstrated by The Ohio State University (OSU) student team as part of the Challenge X advanced vehicle development competition. In 2008, the team participated in the final year of the competition with a highly refined hybrid-electric vehicle (HEV) that uses a through-the-road parallel architecture.

The paper studies the distributions of residual stresses in auto components after induction hardening. Three prototype parts are analyzed in this paper. Firstly, the temperature fields of the analyzed parts are quantitatively simulated during quenching by simulating surface heating to the austenitization temperature of the material. Secondly, the formation and states of the residual stresses are predicted. Therefore the distribution of residual stress is simulated and shows compressive stresses on the surface of components so that the strength can be improved. The simulated results by computer are compared with experimental results. The good comparison indicates that the results obtained by the FEA analysis are reliable. Thus, it can be concluded that the FEA (Finite element analysis) program is effectively developed to simulate heating and quenching processes and residual stresses distribution.

In racetrack conditions, brake systems are subjected to extreme energy loads and energy load distributions. This can lead to very high friction surface temperatures, especially on the brake corner that operates, for a given track, with the most available traction and the highest energy loading. Individual brake corners can be stressed to the point of extreme fade and lining wear, and the resultant degradation in brake corner performance can affect the performance of the entire brake system, causing significant changes in pedal feel, brake balance, and brake lining life. It is therefore important in high performance brake system design to ensure favorable operating conditions for the selected brake corner components under the full range of conditions that the intended vehicle application will place them under. To address this task in an early design stage, it is helpful to use brake system modeling tools to analyze system performance.

The influence of elevated temperature forming on local mechanical properties of AZ31B magnesium (Mg) sheet material was investigated. The Mg sheet was formed into a closure component with high temperature gas pressure at 485°C. Miniature tensile testing specimens were cut from selected areas of the component where different levels of thinning occurred. The specimens were strained in tension to fracture using a miniature tensile stage. The two-dimensional strain distribution in the necking region along with true stress-true strain curves were computed using a digital image correlation technique to assess the influence of the forming-induced thinning on tensile strength and percent elongation at fracture.

Under the initiative of the United States Council for Automotive Research LLC (USCAR§) Transmission Working Group, a collaborative effort was made with LuK USA LLC to study the influence of the friction interface parameters on the shudder durability of a wet launch clutch. Clutch configurations with different combinations of four friction materials (A, B, C and D), three groove patterns (waffle, radial and waffle-parallel) and two separator plate conditions (nitrided and non-nitrided) were considered. Durability testing consisted of a test profile, with 110 kJ energy per test cycle, developed earlier in this project. Materials A, B and C with nitrided separator plates reached the end of test criteria for the torque gradient and showed shudder. Materials B and C were more wear resistant as compared to materials A and D. The loss of friction coefficient (μ) was lower for materials B, C and D as compared to material A.