Search Results

When the engine oil evaporates in the crankcase, it is necessary to discharge to the outside of the engine or returns to the intake air as part of blow-by gas. The amount of oil content in the blow-by gas is preferable to be as small as possible. This paper researched the evaporation characteristics of diesel engine oil for heavy duty into blow-by gas using 5W-30 and 10W-30 engine oils with the equivalent to Noack. As a result, it is found that evaporate phenomenon cannot be explained well enough by just Noack and clarified of the oil evaporation mechanism in blow-by gas.

It has been proposed that downspeeding combined with high boost levels would effectively reduce fuel consumption in heavy-duty diesel engines. Under low-speed and high-boost operating conditions, however, the in-cylinder gas pressure, which acts on the piston crown, is greater than the piston inertia force (such that there is no force reversal), over the entire range of crank angles. Therefore, the piston pin never lifts away from the main loading area (the bottom) of the connecting rod small-end bushing where the contact pressure against the piston pin is highest. In such operating conditions, lubricant starvation is easily induced at the interface between the piston pin and small-end bushing. Through carefully devised engine tests, the authors confirmed that the piston pin scuffing phenomenon arises when the boost pressure exceeds a critical value at which the no-force reversal condition appears.

More stringent emissions regulations, fuel economy standards, and regulations are currently being discussed to help reduce both CO2 and exhaust emissions. Vehicle manufacturers have been developing new engine technologies, such as downsizing and down-speeding with reduced friction loss, improved engine combustion and efficiency, heat loss recycling, power-train friction loss recycling, and reduced power-train friction loss. The use of more efficient fuel economy 5W-30 engine oils for heavy duty commercial vehicles has started to expand since 2009 in Japan as one technological solution to help reduce CO2 emissions. However, fuel economy 5W-30 oils for use in heavy duty vehicles in Europe are mainly based on synthetic oils, which are much expensive than the mineral oils that are predominantly used in Japan.

The friction pattern on the chamfers of sleeves and dog gears is a combination of peeling and adhesive wear caused by the formation and propagation of fine cracks. The effect of additional elements on wear were checked by making a test apparatus capable of performing evaluations on test pieces equivalent to those using actual parts. The results showed that the addition of B, Ti-Nb helped improve wear resistance. This is attributed to enhanced toughness and reduced peeling due to the formation of a texture. A 45% reduction in wear was achieved in actual parts tests on steel with added B, Ti-Nb.

In heavy duty (HD) trucks cruising on expressway, about 60% of input fuel energy is wasted as losses. So it is important to recover them to improve fuel economy of them. As a waste heat recovery system, a Rankine cycle generating system was selected. And this paper mainly reports it. In this study, engine coolant was determined as main heat source, which collected energies of an engine cooling, an EGR gas and an exhaust gas, for collecting stable energy as much as possible. And the exergy of heat source was raised by increase coolant temperature to 105 deg C. As for improving the system efficiency, saturation temperature difference was expanded by improving performance of heat exchanger and by using high pressure turbine. And a recuperator which exchanges heat in working fluid between expander outlet and evaporator inlet was installed to recover the heat of working fluid at turbine generator. Then a working fluid pump was improved to reduce power consumption of the system.

Diesel engine has a good fuel economy and high durability and used widely for power source such as heavy duty in the world. On the other hand, it is required to reduce NOx (Nitrogen Oxides) and PM (Particulate Matter) emissions further from diesel exhaust gases to preserve atmosphere. The urea-SCR (Selective Catalytic Reduction) system is the most promising measures to reduce NOx emissions. DPF (Diesel Particulate Filter) system is commercialized for PM reduction. However, in case that a vehicle has a slow speed as an urban area driving, a diesel exhaust temperature is too low to activate SCR catalyst for NOx reduction in diesel emissions. Moreover, the diesel exhaust temperature becomes lower as a future engine has less fuel consumption. The purpose of this study is reduction of NOx emission from a heavy-duty diesel engine using the Urea SCR system at the low temperature.

The spark-assisted methanol engine has disadvantages like poor fuel economy especially at light load and low spark plug durability affected by combustion characteristics. Investigations of combustion characteristics of the spark ignition system and the autoignition system in the methanol engine and discharge characteristics of a spark plug are described in this paper. It is clear that effective autoignition was accomplished by increasing the compression ratio and adopting an EGR system in the spark-assisted methanol engine. This new improved methanol engine which is named HAMS achieved good fuel economy at light load, a low NOx emission and longer spark plug life. And a heat insulated piston with a stainless steel cap is being investigated for further improvement of autoignition combustion characteristics.

Hino Motors is about to launch a new truck model FA as a family product of the model FB class 5 category trucks which have been sold since 1986, Model FA, a class 3 category cab-over-engine truck has a GVW of 13,500 Lbs. and is powered by a 3.8 liter direct injection turbocharged diesel engine which produces 125 HP in conformity with federal exhaust gas emission regulations for 50 states. The new truck was designed and developed to satisfy several principal design objectives such as excellent maneuverability, driving comfort, superior fuel economy as well as sufficient reliability and durability within the simplest possible structure. This paper describes its design objectives, features focusing on cab and engine and technologies devoted to the development.

It is preferable that power steering permits “static park” and has a good “road Feel” when running. In order to permit “static park”, a large bore actuation cylinder with high flow pump is required. Such a method, however, has two defects, a loss power for driving a large volume pump and a poor “road feel”. Resolving these problems and achieving the above matters. Hino has developed a load sensing power steering system. This system, which employes two actuation cylinders controlled by means of a unique load sensing valve arrangement, is designed to permit use of only one cylinder for highway speeds and both cylinders during a static park maneuver. When the system is combined with the preceding speed sensing power steering, “static park” is further facilitated and a tasty “road feel” is available in accordance with vehicle speed.

A historical review of Japanese turbocharged diesel engines for heavy duty vehicles is described, and newly developed turbocharged diesel engines of HINO are introduced. The design features of these engines include new turbocharging technologies such as highly backward curved impeller for compressor blade, variable controlled inertia charging and waste gate. Laboratory and field test results demonstrated better fuel economy and improved low speed and transient torque characteristics than the predecessors. Several operational experiences, technical analysis and reliability problems are discussed.

A new combustion system for a light duty D.I. diesel engine was developed, and a 3.5 ton payload truck (6.5 ton G.V.W.) equipped with this D.I. diesel engine and this combustion system realized good fuel economy and lower exhaust gas emission. Generally, light duty vehicles have to operate over a wide engine speed range. Therefore application of a D.I. diesel engine to light duty vehicles is difficult because of combustion tuning requirements over a wide engine speed range. Up to now, most of the diesel engines for light vehicles have been of the I.D.I. type. But the D.I. diesel engine has an evident advantage of lower fuel consumption. In these circumstances the authors developed a new combustion chamber shape for a small D.I. diesel engine with turbulence induced intake port and optimum fuel injection equipment. Various combustion chamber geometries were tested and evaluated.