Search Results

Portable emission measurement systems (PEMS) for particle number (PN) counting are under development in Europe, along with the vehicle testing protocol. A PN PEMS was developed by using a non-heated exhaust diluter, and applying a diffusion charger sensor (DCS) as the PN detector which is fitted with diffusion screens in order to selectively remove all particles, including volatiles, below 30 nm. Detection efficiencies of the DCS could be successfully adjusted by the number of diffusion screens installed before it. Equivalent results of the PN PEMS to a conventional system were observed by vehicle tests. However, variations were observed under specific vehicle operating conditions. Also, as part of the same program, a commercially available hand-held condensation particle counter (CPC) was compared with the standard CPC by vehicle tests as one of candidates to PEMS. Differences in PN concentrations were observed depending on the engine conditions

The subject of engine emissions is expected to be at the forefront of environmental regulations and consumers’ concerns for years to come. As technology develops to comply with new and different requirements in various regions of the world, understanding the fundamental principles of how engine emissions occur, and how they can be properly measured, is vitally important. Engine Emissions Measurement Handbook, developed and co-authored by HORIBA Automotive Test Systems team addresses the main aspects of this subject. Written with the technical user in mind, this title is a must-have for those involved in engine development and testing, and environmental researchers focusing on better ways to minimize emissions pollution.

Most of the recent clean diesel engines are equipped with an exhaust gas recirculation (EGR) technology in order to meet the strict criteria of NOx and particulate matter (PM) as required in the current emission regulations. More attention to strict EGR control is becoming required. Accurate and fast transient EGR ratio operation is becoming very critical in the field of the emission control. The EGR ratio is typically monitored by CO₂ trace method, in which CO₂ emitted from engine, is utilized as a tracer gas. The EGR ratio can be obtained from CO₂ concentration measured at engine intake and engine out at the same time. In this study, authors have developed a new EGR analyzer consisting of two CO₂ detectors, to achieve required performance for transient measurement, i.e., short delay time and quick response, negligible difference between two CO₂ detectors, and capability of wet measurement.

A new on-board portable emission measurement system (PEMS) for gaseous emissions has been designed and developed to meet CFR Part 1065 requirements. The new system consists of a heated flame ionization detector (HFID) for the measurement of total hydrocarbon, a heated chemiluminescence detector (HCLD) for the measurement of NOx, and a heated non-dispersive infra-red detector (HNDIR) for the measurement of CO and CO2. The oxygen interference and relative sensitivity of several hydrocarbon components have been optimized for the HFID. The CO2 and H2O quenching effect on the HCLD have been compensated using measured CO2 and H2O concentration. The spectral overlap and molecular interaction of H2O on the HNDIR measurement has also been compensated using an independent H2O concentration measurement. The basic performance of the new on-board emission measurement system has been verified accordingly with CFR part 1065 and all of the performances have met with CFR part 1065 requirement.

The Flame Ionization Detector (FID) used to measure hydrocarbon content in emission samples uses a hydrogen flame that produces little ionization. Hydrocarbons introduced into this flame produce large numbers of ions with ionization proportional to the number of carbon atoms present. This proportionality can be skewed by variations in oxygen content. Oxygen variation in emission samples, cylinders of air or span/calibration gas, and zero air systems are investigated and their effects on emission results are discussed. The oxygen content of the gas under analysis will affect the hydrocarbon concentration reported by the FID. In the example examined in this paper, the oxygen effect was shown to decrease the FTP (Federal Test Procedure) weighted NMHC (Non-Methane Hydrocarbon) results by as much as 7 % for a BMD (Bag Mini-Diluter) sample and 13% for a CVS (Constant Volume Sampling) sample.

A sulfur analyzer utilizing an ultraviolet fluorescent (UVF) detector has been developed to measure sulfur components in vehicle emissions. Generally, it is considered that an UVF detector cannot be used to measure sulfur components in vehicle emission due to a significant interference from NO in sample gases. In this study, an O3 injection technique has been developed to eliminate NO interference. Using this technique, the interference from NO has been reduced to less than 0.01 ppm with 3000 ppm NO. These result show a capability of utilizing UVF with this O3 injection technique to measure sulfur components in vehicle emissions including emissions with high concentrations of NO. An oxidation catalyst has also been evaluated to measure total reduced sulfur, TRS.

Due to a need for a robust measurement system for on-board real-world vehicle emission measurement, a heated ND-IR(h-NDIR) technique has been developed and evaluated for its potential. The h-NDIR is capable of measuring CO and CO2 under wet-based condition by correcting interference from co-existing gas with an algorithm specially developed for the present study. The resulting H2O interference to the CO2 measurement is less than 0.01vol% for zero point and less than ±1% for span points and that of CO measurement is less than 0.001vol% for zero point and less than ±2% for span point against 0 to12vol% H2O. An on-board emission measurement system using the h-NDIR in combination with an Annubar® flow meter and an air to fuel ratio sensor has been evaluated. The result reveal correlation between the present system and a chassis test system to be within 7% for fuel consumption, within 5% for CO mass emission, and within 6% for CO2 mass emission.