Search Results

Recently, as part of the effort to enhance fuel efficiency and reduce costs for eco-friendly vehicles, the R-gearless system has been implemented in the TMED (P)HEV system. Due to the removal of the reverse gear, a distinct backward driving method needs to be developed, allowing the Electronic Motor (e-Motor) system to facilitate backward movement in the TMED (P)HEV system. However, the capability of backward driving with the e-Motor is limited because of partial failure in the high-voltage system of an R-gearless system. Thus, we demonstrate that it is possible to improve backward driving problems by applying a new fail-safe strategy. In the event of a high-voltage battery system failure, backward driving can be achieved using the e-Motor with constant voltage control by the Hybrid Starter Generator (HSG), as proposed in this study.

Engine off control is conducted on parallel hybrid vehicles in order to reduce fuel consumption. It is efficient in terms of fuel economy, however, noise and vibration is generated on engine cranking and transferred through engine mount on every mode transition from EV to HEV. Engine crank position control has been studied in this paper in order to reduce vibration generated when next cranking starts. System modeling of an architecture composed of an engine, P1 and P2 motors has been conducted. According to the prior studies, there exists correlation between crank vibration level and the crank angle. Thus a method to locate pistons on a specific crank angle which results in a local minimum of vibration magnitude could be considered. The P1 motor facilitates this crank position control when engine turns off, for its location directly mounted on a crankshaft allows the system model to obtain more precise crank position estimation and improved linearity in torque control as well.

To improve the fuel efficiency and satisfy the strict emission regulations, the development of internal combustion engine gets more complicated in both hardware and software perspectives, and the margins for durability and NVH quality become narrower, which could result in poor NVH robustness in harsh engine operating conditions. In this paper, we investigate experimentally the camshaft impact noise mechanism relating the valve train and timing chain forces to detailed motion of the camshaft and the chain tensioner. After the initial investigation of identifying the impact timings and specific engine operating points when the noise occurs, the camshaft orbital motion inside of the sliding bearing is measured and visualized with the proximity sensors with calibration after sensor mounting, in addition to the chain tensioner movements.

As the carbon neutrality to reduce greenhouse gas emissions has become a global movement, the development of power sources using carbon-free fuels is an essential task for the industry. Accordingly, many companies in various fields that need carbon reduction are striving to develop power sources and build energy value chains using carbon-free or carbon-neutral fuels such as hydrogen and E-fuel. Ammonia, which is also a carbon-free fuel, stands as an efficient energy vector delivering high energy density and flexibility in transportation and storage, capable of mitigating hydrogen’s key drawbacks. However, difficulty of controlling combustion of ammonia due to its fuel characteristics limited the development of internal combustion engines using ammonia to the basic research stage in the limited operating conditions. Hyundai Motor Company presents the development of ammonia fueled 4-cylinder SI engine using direct injection strategy, designed based on 2.5L LPG T-DI engine.

Platoon is a system that connects vehicles through vehicle-to-vehicle (V2V) communication technology to maintain a short distance between vehicles while driving on the road. To improve fuel efficiency, many automotive original equipment manufacturers (OEMs) are interested in developing and demonstrating real-world platoon system. However, it is hard for heavy duty trucks to develop this system due to the difficulty of maintaining the targeted intervehicle distance not only for fuel efficiency but also for safety in case of emergency braking. Because of this critical safety issue in the emergency situation, the platoon system for heavy duty trucks can be hardly demonstrated or tested in real vehicle environment. The relatively complex system and the slow response characteristic of commercial vehicles makes this even more difficult.

An experimental study was conducted on a multi-cylinder engine to understand the feasibility of a six-stroke homogeneous charge compression ignition (HCCI) operation under stoichiometric conditions. State-of-the-art technologies such as continuously variable valve duration (CVVD) and high-pressure gasoline direct injection (GDI) were experimentally exploited to increase the degree of freedom of engine control. The motivation of six-stroke HCCI combustion is to remedy the load limitation and the cyclic variation in four-stroke HCCI combustion with two additional strokes: compression and expansion strokes. The six-stroke HCCI combustion occurs in the following order. First, hot residual gas is trapped by applying negative valve overlap (NVO). Next, fresh air enters, fuel is injected, and lean HCCI combustion occurs in the 1st power stroke (PS). Subsequently, additional fuel is injected, and the 2nd combustion occurs with the remaining oxygen in the two additional strokes.

As global emission standards are becoming more stringent, it is necessary to increase thermal efficiency through the high compression ratio in spark-ignited engines. Various studies are being conducted to mitigate knocking caused by an increased compression ratio, which requires an understanding of the combustion phenomena inside the combustion chamber. In particular, the in-cylinder flow is a major factor affecting the entire combustion process from the generation to the propagation of flames. In the field of spark-ignited engine research, where interest in the concept of lean combustion and the expansion of the EGR supply is increasing, flow analysis is essential to ensure a rapid flame propagation speed and stable combustion process. In this study, the flow around the spark plug was measured by the Laser Doppler Velocimetry system, and the correlation with combustion in spark-ignited engines was analyzed.

Since the amount of emitted CO2 is directly related to car fuel economy, attention is being drawn to DISI (Direct-Injection Spark-Ignition) engines, which have better fuel economy than conventional gasoline engines. However, it has been a problem that the rich air-fuel mixtures associated with fuel films during cold starts due to spray impingement produce particulate matter (PM). In predicting soot formation, it is important to predict the mixture field precisely. Thus, accurate spray and film models are a prerequisite of the soot model. The previous models were well matched with low-speed collision conditions, such as those of diesel engines, which have a relatively high ambient pressure and long traveling distances. Droplets colliding at low velocities have an order of magnitude of kinetic energy similar to that of the sum of the surface tension energy and the critical energy at which the splash occurs.

The combustion process using two fuels with different reactivity, known as dual-fuel combustion or RCCI is mainly studied to reduce emissions while maintaining thermal efficiency compared to the conventional diesel combustion. Many studies have proven that dual-fuel combustion has a positive prospect in future combustion to achieve ultra-low engine-out emissions with high indicated thermal efficiency. However, a limitation on high-load expansion due to the higher maximum in-cylinder pressure rise rate (mPRR) is a main problem. Thus, it is important to establish the operating strategy and study the effect of in-cylinder flow motion with dual-fuel combustion to achieve a low mPRR and emissions while maintaining high-efficiency. In this research, the characteristics of gasoline-diesel dual-fuel combustion on different hardware were studied to verify the effect of the in-cylinder flow motion on dual-fuel combustion.

In recent years, emission regulations have been getting increasingly strict. In the development of engines that comply with these regulations, in-cylinder pressure plays a fundamental role, as it is necessary to analyze combustion characteristics and control combustion-related parameters. The analysis of in-cylinder pressure data enables the modelling of exhaust emissions in which characteristic temperature can be derived from the in-cylinder pressure, and the pressure can be used for other investigations, such as optimizing efficiency and emissions through controlling combustion. Therefore, a piezoelectric pressure sensor to measure in-cylinder pressure is an essential element in the engine research field. However, it is difficult to practice the installation of this pressure sensor on all engines and on-road vehicles owing to cost issues.

As emissions regulations become stricter, a variety of advanced combustion concepts that can reduce emissions with a higher thermal efficiency have been suggested. Dual-fuel combustion is one of the alternatives that has both premixed and non-premixed combustion characteristics. Knowing the effects of the mixture formation in dual-fuel combustion is important because it determines the ignition location and the following combustion phase. Hence, a thorough investigation on the related factors, such as the engine hardware or fuel spray, is required. Meanwhile, Computational Fluid Dynamics (CFD) is a good technique to visualize the in-cylinder phenomena and enables quantitative investigations into the detailed combustion characteristics. In this paper, a 3-dimensional CFD simulation was used to investigate the effects of the mixture formation in dual-fuel combustion. The combustion model consists of two parts.

The integration of SCR catalyst into diesel-particulate filter (SDPF) may be one of most viable ways to meet upcoming stringent emission regulations with new test protocols such as Worldwide harmonized Light vehicles Test Cycles (WLTC) and Real Driving Emissions (RDE) requirements. The chabazite-structured SSZ-13-based catalysts enabled the wide implementation of urea-SCR technology for mobile applications due to their robust thermal stability up to 750°C compared to the thermally unstable ZSM-5-based technologies. However, the thermally stable Cu-SSZ-13 catalyst starts losing its initial activity with the increase of aging time at 850°C, where the SCR catalyst on SDPF can possibly be exposed during filter regeneration under a drop-to-idle (DTI) condition. Therefore, more durable SCR catalysts that survive under higher temperatures have been strongly desired in automotive industry. Recently, we found Cu-exchanged high silica LTA revealed an excellent hydrothermal stability.

Generally, vehicles do not need power during deceleration. Therefore, the fuel efficiency can be improved by stopping the fuel injection in this period. However, when the fuel cut is activated, NOx is emitted immediately after fuel cut. During the fuel cut period, a large amount of fresh air flows into the catalytic converter installed on a vehicle since there is no combustion. Thus, the catalytic materials are converted into an oxidizing atmosphere. As a result, NOx purification performance of the catalyst deteriorates, and eventually NOx is emitted when combustion restarts. The quantity of NOx in this period is relatively small. However, in case of increasing fuel cuts, emission problem could arise. Therefore, in order to meet the stringent regulation such as LEV III-SULEV20 or 30, the number of fuel cuts need to be limited. The problem is that this strategy leads to a disadvantage of fuel efficiency.

Recently, the design of automotive headlamps has become diversified and complicated according to customer needs. Hence, structural complexity of the headlamps has also increased. Complex structure of the headlamps inevitably causes a disturbance in air circulation. For this reason, inadvertent micro-sized water droplets, called fogging, are condensed on the inner surface of headlamp lens due to temperature difference between the inner and outer lens surfaces. To circumvent fogging inside of the headlamp lens, an anti-fogging coating is indispensable. Conventionally, diverse surfactants have been adopted as substantial material for the anti-fogging coating. However, the usage of the surfactants causes undesirable side effect such as water mark arising from vapor condensation, which is an important issue that must be fully resolved. In this study, we developed an innovative anti-fogging coating material without using conventional surfactant.

This model based investigation is carried out in order to control the half order modulation for diesel engines using by virtual calibration approach and proposes a feedback control strategy to mitigate cylinder to cylinder imbalance from asymmetric cylinders torque production. Combustion heat release analysis is performed on test data to understand the root cause of observed cylinder to cylinder pressure variations. The injected fuel variations are shown to cause the observed pressure variations between cylinders. A feedback control strategy based on measured crank shaft position is devised to control the half order modulation to balance the combustion pressure profile between cylinders. This control strategy is implemented in Simulink and is tested in closed-loop with the diesel engine model in AMESim. The closed-loop performance indicates that the half order modulation is considerably improved while having minimal impact on the fuel consumption.

The worldwide fuel economy compliance level has been tightening, at the same time, LEV-III/Euro-6d/China-6/BS-6 regulations for NMOG and NOx emissions are being introduced or already effective. Therefore, intensive research effort has been conducted in order to improve the fuel efficiency of passenger cars and reduce exhaust emission. In response to these demands, turbocharged gasoline direct injection (TGDI) engine is being introduced for gasoline vehicles in consideration of fuel efficiency improvement, high output and driving performance compared to naturally aspirated (NA) engine. However, due to its larger thermal mass from the turbo hardware in the exhaust, it suffers from the cold-start emission. The main hazardous gases emitted from gasoline vehicles are CO, HC and NOx, and a three-way catalyst (TWC) is installed for the purification of these harmful emissions.

The flame propagation characteristic is one of the greatest factor that determines the performance of spark ignition (SI) engines. The in-cylinder flow dynamics is very significant in terms of flame propagation because of its direct influence on the flame shape, turbulent flame speed, and the ignition quality. A number of different techniques are available to optimize the in-cylinder flow and maximize the utilization of turbulence for faster combustion, and tumble enhancement by intake port geometry is one of them. It requires excessive computational expenses to evaluate multiple designs under wide range of operating conditions by 3D-CFD, therefore, a low-dimensional model would be more competitive in such design optimization process. This work suggests a new modification approach for typical 0D turbulence model to take account for the tumble generation during the intake process as well as the turbulence characteristics associated with it.

As fuel injection strategies in spark-ignition (SI) engines have been diversified, inhomogeneous mixing of the fuel-air mixture can occur to varying extents during mixture preparation. In this study, we analyzed the effect of inhomogeneous mixing on the knocking characteristics of iso-octane and air mixture under a standardized fuel testing condition for research octane number (RON), based on ASTM D2699. For this purpose, we assumed that both lean spots and rich spots existed in unburned gas during compression stroke and flame propagation and calculated the thermodynamic state of the spots by using an in-house multi-zone, zero-dimensional SI engine model. Then, the ignition delay was measured over the derived thermodynamic profiles by using rapid compression machine (RCM), and we calculated ξ, the ratio of sound speed to auto-ignition propagation speed, based on Zel’dovich and Bradley’s ξ − ε theory to estimate knock intensity.

As environmental problems such as global warming are emerging, regulations on automobile exhaust gas are strengthened and various exhaust gas reduction technologies are being developed in various countries in order to satisfy exhaust emission regulations. Exhaust gas recirculation (EGR) technology is a very effective way to reduce nitrogen oxides (NOx) at high combustion temperatures by using EGR coolers to lower the combustion temperature. This EGR cooler has been mass-produced in stainless steel, but it is expensive and heavy. Recently, high efficiency and compactness are required for the EGR cooler to meet the new emission regulation. If aluminum material is applied to the EGR cooler, heat transfer efficiency and light weight can be improved due to high heat transfer coefficient of aluminum compared to conventional stainless steel, but durability is insufficient. Therefore, the aluminum EGR cooler has been developed to enhance performance and durability.

In recent years, the emerging technology competitions in automotive industry are improving engine efficiency and electronizing for coping with stringent fuel-economy regulations. However, fuel-economy technologies such as engine down-sizing and numerous electronic parts entrust burden plastic materials acing as mainly electric insulation and housing to have to be higher performance, especially temperature endurance. Engineering plastics (EPs) have critical limitations in terms of degradation by heat. Heat-resisting additives in EP are generally used to be anti-degradation as activating non-radical decomposition of peroxide. However, it could not be effective way to impede the degradation in long term heat aging over 1,000 hours at high temperature above 180 °C. In this study, we suggested the new solution called ‘shield effect’ that is purposeful oxidation at the surface and local crystallization of EP to stop prevent penetrating oxygen to inside of that.