Search Results

Battery packs of electric vehicles are typically composed of lithium-ion batteries with aluminum and copper acting as cell terminals. These terminals are joined together in series by means of connector tabs to produce sufficient power and energy output. Such critical electrical and structural cell terminal connections involve several challenges when joining thin, highly reflective and dissimilar materials with widely differing thermo-mechanical properties. This may involve potential deformation during the joining process and the formation of brittle intermetallic compounds that reduce conductivity and deteriorate mechanical properties. Among various joining techniques, laser welding has demonstrated significant advantages, including the capability to produce joints with low electrical contact resistance and high mechanical strength, along with high precision required for delicate materials like aluminum and copper.

The fusion of multi-modal perception in autonomous driving plays a pivotal role in vehicle behavior decision-making. However, much of the previous research has predominantly focused on the fusion of Lidar and cameras. Although Lidar offers an ample supply of point cloud data, its high cost and the substantial volume of point cloud data can lead to computational delays. Consequently, investigating perception fusion under the context of 4D millimeter-wave radar is of paramount importance for cost reduction and enhanced safety. Nevertheless, 4D millimeter-wave radar faces challenges including sparse point clouds, limited information content, and a lack of fusion strategies. In this paper, we introduce, for the first time, an approach that leverages Graph Neural Networks to assist in expressing features from 4D millimeter-wave radar point clouds. This approach effectively extracts unstructured point cloud features, addressing the loss of object detection due to sparsity.

The characterization of sheet metals under in-plane uniaxial bending is challenging due to the aspect ratios involved that can cause buckling. Anti-buckling plates can be employed but require compensation for contact pressure and friction effects. Recently, a novel in-plane bending fixture was developed to allow for unconstrained sample rotation that does not require an anti-buckling device. The objective of the present study is to design the sample geometry for sheared edge fracture characterization under in-plane bending along with a methodology to resolve the strains exactly at the edge. A series of virtual experiments were conducted for a 1.0 mm thick model material with different hardening rates to identify the influence of gage section length, height, and the radius of the transition region on the bend ratio and potential for buckling. Two specimen geometries are proposed with one suited for constitutive characterization and the other for sheared edge fracture.

Electrical steel, also known as silicon steel, is a ferromagnetic material that is often used in electric vehicles (EVs) for stator and rotor applications. Since the design and manufacturing of rotors require the use of laminated thin electrical steel sheets, the fatigue characterization of these single sheets is of interest. In this study, a 0.27mm thick non-oriented electrical steel sheet was tested under cyclic loading in the load-controlled mode with the load ratio R = 0.1 at room temperature. The specimens were prepared using the Computer Numerical Control (CNC) machining method. The Smith-Watson-Topper mean stress correction was used to find the equivalent fully reversed stress-life (S-N) curve. The Basquin equation was used to describe the fatigue strength of the electrical steel and the fatigue parameters were extracted. Furthermore, a design curve with a reliability of 90% and a confidence level of 90% was generated using Owen’s Tolerance Limit method.

Highly autonomous vehicles have drawn the interests of many researchers in recent years. For highly autonomous vehicles, a high-definition (HD) map is crucial since it provides accurate information for autonomous driving. However, due to the possible fast-changing environment, the performance of HD maps will deteriorate over time if timely updates are not ensured. Therefore, this paper studies the updating of lightweight HD maps in closed areas. Firstly, a novel two-layer map model called a lightweight HD map is introduced to support autonomous driving in a flexible and efficient way. Secondly, typical updating of scenarios in closed areas with non-paved roads is abstracted into operations including area border expansion, road addition, and road deletion. Meanwhile, a map updating framework is proposed to address the issue of map updating in closed areas. Finally, an experiment is conducted to demonstrate the feasibility and effectiveness of the proposed map updating approach.

Panoramic images can provide critical information for Advanced Driving Assistance Systems (ADAS), such as parking spaces and surrounding vehicles. However, the vehicle in the bird's-eye view image is severely distorted and incomplete, and the visual information becomes very blurred in some illumination insufficient environments. If the driver cannot see the surrounding environment information, the risk of collision will increase, especially during parking. To better percept the local environment with the help of panoramic images, we use panoramic image segmentation results to construct a virtual surround view monitoring system to provide drivers with clearer perception information. Firstly, a lightweight segmentation network is redesigned based on SegNet, which will improve the accuracy of the segmentation without increasing the model’s inference time. Secondly, we build an augment visualization around view monitor (AV-AVM) system with regards to the segmentation results.

As one of the most challenging driving tasks, parking is a common but particularly troublesome problem in large cities. Recently, an excellent solution-automated valet parking (AVP) has become a hot research topic, which allows the driver to leave the vehicle in a drop-off area, while the vehicle driving into the parking slot by itself. For AVP, the precise localization is an indispensable module. However, the global positioning system (GPS) cannot be used in the underground parking lot and the localization method based on lidar is too expensive. In response to solve this problem, we propose a simultaneous localization and mapping system with the semantic information of parking slots (PS-SLAM), which is based on visual-inertial and around view images. First, the calibration of multi-sensors is conducted to obtain their intrinsic and extrinsic parameters. In this way, the around view image and transformation matrices between sensors can be acquired.

The around view monitor (AVM) system for vehicles usually suffers from the distortion of surrounding objects caused by incomplete rectification and stitching, which seriously affects the driver's judgment of the surrounding environment during the reversing process. In response to solve this problem, an augmented around view monitor (AAVM) system fusing image and depth information is proposed, which highlights the point clouds of persons or vehicles at the rear of the vehicle. First, an around view image is generated from four fisheye cameras. Then, the calibration of multi TOF cameras is conducted to improve their accuracy of depth estimation and obtain extrinsic camera positions. Next, the 2D-driven object point cloud detection method is proposed to localize and segment object point clouds like vehicles or persons.

HTL is a kind of biodiesel converted from wet biowaste via hydrothermal liquefaction (HTL), which has drawn increasing attention in recent years due to its wide range of raw materials (algae, swine manure, and food processing waste). However, from the previous experiments done in a constant volume chamber, it was observed that the presence of 20% of HTL in the blend produced as much soot as pure diesel at in chamber environment oxygen ratio of 21%, and even more soot at low oxygen ratios. It was also observed that n-butanol addition could reduce the soot emission of diesel significantly under all tested conditions. In this work, the spray and combustion characteristics of HTL and diesel blends with n-butanol added were investigated in a constant volume chamber. The in-chamber temperature and oxygen ranged from 800 to 1200 K and 21% to 13%, respectively, covering both conventional and low-temperature combustion (LTC) regimes.

Flash boiling has drawn much attention recently for its ability to enhance spray atomization and vaporization, while providing better fuel/air mixing for gasoline direct injection engines. However, the behaviors of flash boiling spray with multi-component fuels have not been fully discovered. In this study, isooctane, ethanol and the mixtures of the two with three blend ratios were chosen as the fuels. Measurements were performed with constant fuel temperature while ambient pressures were varied to adjust the superheated degree. Macroscopic and microscopic characteristics of flash boiling spray were investigated using Diffused Back-Illumination (DBI) imaging and Phase Doppler Anemometry (PDA). Comparisons between flash boiling sprays with single component and binary fuel mixtures were performed to study the effect of fuel properties on spray structure as well as atomization and vaporization processes.

The spray structure and vaporization processes of flash-boiling sprays in a constant volume chamber under a wide range of superheated conditions were experimentally investigated by a high speed imaging technique. The Engine Combustion Network’s Spray G injector was used. Four fuels including gasoline, ethanol, and gasoline-ethanol blends E30 and E50 were investigated. Spray penetration length and spray width were correlated to the degree of the superheated degree, which is the ratio of the ambient pressure to saturated vapor pressure (pa/ps). It is found that parameter pa/ps is critical in describing the spray transformation under flash-boiling conditions. Three distinct stages namely the slight flash-boiling, the transition flash-boiling, and the flare flash-boiling are identified to describe the transformation of spray structures.

The around view monitor (AVM) system for the long-body road vehicle with multiple articulated carriages usually suffers from the incomplete distortion rectification of fisheye cameras and the irregular image stitching area caused by the change of relative position of the cameras on different carriages while the vehicle is in motion. In response to these problems, a set of calibration and stitching methods of AVM are proposed. First, a radial-distortion-based rectification method is adopted and improved. This method establishes two lost functions and solves the model parameters with the two-step optimization method. Then, AVM system calibration is conducted, and the perspective transformation matrix is calculated. After that, a static basic look-up table is generated based on the distortion rectification model and perspective transformation matrix.

A three dimensional IR-TRACC (Infrared Telescope Rod for Assessment of Chest Compression) was designed for the Test Device for Human Occupant Restraint (THOR) in recent years to measure chest deflections. Due to the design intricateness, the deflection calculation from the measurements is sophisticated. An algorithm was developed in this paper to calculate the three dimensional deflections of the chest. The algorithm calculates the compression and also converts the results to the local spine coordinate system so that it can correlate with the Post Mortem Human Subject (PMHS) measurements for injury calculation. The method was also verified by a finite element calculation for accuracy, comparing the calculation from the corresponding model output and the direct point to point measurements. In addition, the IR-TRACC calibration methods are discussed in this paper.

The increased use of zinc coatings on steels has led to a decrease in their weldability. Weld current and time need to be increased in order to achieve sound welds on these materials compared to uncoated steels, and electrode tip life suffers greatly due to rapid alloying and degradation. In this work, typical uncoated Class II electrodes were tested along with a TiC metal matrix composite (MMC) coated electrode. Tests were conducted to study the weldability and process of nugget formation for both electrodes on HDG (hot dipped galvanized) HSLA (high strength low alloys) steels. Current and time ranges were constructed for both types of electrodes by varying either the weld current or weld time while holding all other parameters constant. Analysis of weld microstructures was conducted on cross-sectioned welds using SEM (scanning electron microscopy). Using the coated electrodes reduced weld current and times needed to form MWS (minimum weld size) on the coated steels.

Using standard tensile testing methods, the material properties of AKDQ and DP600 steels tubes along the axial direction were determined. A novel in-situ optical strain mapping system ARAMIS® was utilized to evaluate the strain distribution during tensile testing along the axial direction. Microstructural and damage characterization was carried out using microscopy and image analysis techniques to compare the damage evolution and formability of both materials. Failure in both steels was observed to occur via a ductile failure mode. AKDQ was found to be the more formable material as it can achieve higher strains, total elongations and thinning prior to failure than the higher strength DP600.

An investigation based on human visual search functions was conducted into the causative factors of traffic accidents at clear intersections in rural areas. The results indicated that it is difficult for drivers to detect a vehicle traveling on a collision course because the vehicle remains in the same position in the driver's visual field. Two systems are introduced to assist drivers' visual searches. One system uses an image processing technique, and the other utilizes DGPS and IVC techniques. This paper presents the development of the assistance system.

The present work investigates weld failure modes during formability tests of multi-gauge aluminum Tailor Welded Blanks (TWBs). The limiting dome height test is used to evaluate formability of TWBs. Three gauge combinations utilizing aluminum alloy 5754 sheets are considered (2 to 1 mm, 1.6 to 1 mm and 2 to 1.6 mm). Three weld orientations have been considered: transverse, longitudinal and 45°. Interaction of several factors determines the type of failure that occurs in a TWB specimen. These factors are weld orientation, morphology and distribution of weld defects, and the magnitude of constraint imposed by the thicker sheet to the thin sheet. The last factor depends on the difference in thickness of the sheet pair and is usually expressed in terms of gauge ratio. In general TWBs show two different types of fracture: weld failure and failure of the thin aluminum sheet. Only the former will be discussed in this paper.

The objective of this study is to improve tire hydroplaning performance by examining the arrangement of the tread grooves, based on water flow. It is important to smoothly channel the water through the tread grooves to improve performance. For this purpose, flow around the tire contact area was visualized by particle tracing. The velocity and the direction of flow in front of the contact area became clear as a vector map. This vector map indicated that the direction of the flow depends primarily on the lateral position, i.e., the distance from the tread center. Tread grooves parallel to the flow vector were designed based on this result. The visualization of the improved tire demonstrated that water flowed smoothly along the grooves. In addition, a drum test indicated increased cornering force at high speed.