Search Results

In-cabin Noise at low frequency (due to engine or road excitation) is a major issue for NVH engineers. Usually, noise transfer function (NTF) analysis is carried out, due to absence of accurate actual loads for sound pressure level (SPL) analysis. But NTF analysis comes with the challenge of having too many paths (~20 trimmed body attachment locations: engine and suspension mounts, along with 3 directions for each) to work on, which is cumbersome. Physical test transfer path analysis (TPA) is a process of root cause analysis, by which critical contributing paths can be obtained for a problem peak frequency. In addition to that, loads at the attachment points of trimmed body of test vehicle can be derived. Both these outputs are conventionally used in CAE analysis to work on either NTF or SPL. The drawback of this conventional approach is that the critical bands and paths suggested are based on the problem peak frequency of test vehicle which may be different in CAE.

In automotive Front End Accessory Drives (FEAD), the crankshaft supplies power to accessories like alternators, pumps, etc. FEAD undergoes forced vibration due to crankshaft excitation, dynamic tension fluctuations can cause the belt to slip on the accessory pulleys. By considering the criticality of the system, when engine mounting is longitudinally to the vehicle which makes it directly exposed to the air flow containing foreign particles which may cause the damage to the FEAD system and deteriorate the intended functionality. FEAD cover is introduced in the system to enhance belt-pully system functionality by restricting the entry of foreign particles during engine operation. This paper contains a study of FEAD cover failure and provides the stepwise approach to capture such issue during novel model development for 4 cylinder naturally aspirated engine during engine bench testing.

With the increasing competition in the automotive industry, customer experience & satisfaction is at the top of every organization's goals. The customers have evolved & NVH refinement has become the parameter for their decision making in buying a car. The major source of rumble noise in a vehicle is the induced vibrations due to combustion forces in an IC engine. These vibrations are then transferred to the vehicle body through engine mounts. Hence engine mounts play a key role in defining the NVH & the ride performance of any vehicle. However, it is infeasible to validate every mount design through the physical test as it will be both costly & time-consuming. But multiple design iterations can be verified by the CAE approach quite effectively. This paper focuses on the novel CAE approach to evaluate the mount vibrations due to engine dynamics. The process involves preparing a FEA model of the complete Powertrain system.

With advancement of technologies, upgradation of validation procedures and equipment on engine dynamometer test bed is required to simulate environment similar to vehicle and achieve accurate test results. A coolant conditioning system helps in achieving desired temperatures of coolant in the circuit during engine validation. However, unlike radiator type cooling systems of vehicles, conventional coolant conditioning systems on engine test beds generate negative pressure in circuit which poses a risk of coolant boiling, loss of intended heat transfer and hence higher temperature in cylinder head which can be detrimental for durability of critical components like valves, valve seats etc. This paper encompasses a stepwise approach followed to attain near-vehicle coolant pressure conditions for a naturally aspirated engine. Coolant used for this experiment was 50:50 (by volume) ethylene glycol and water mixture.

With strict upcoming regulation norms, it becomes a challenging task for automotive industry to develop highly efficient engine that meets all the regulation requirements. The focus of automakers is to utilize fuel energy in most efficient way and to reduce the energy loss from the engine to improve thermal efficiency. Heat loss to the cooling medium is one of the prime losses inside the combustion chamber. Thermal barrier coating is used to reduce heat losses across combustion chamber surfaces (Piston, head, valves and cylinder liner) as it provides good insulation because of the prominent properties of coating materials like low thermal conductivity, low heat capacity, high melting point etc. This paper presents application and impact of thermal swing coating on thermal efficiency. Thermal swing coating material follows gas temperature quickly throughout the cycle which reduces the temperature difference between gas and coating surface and thus reduces the heat loss.

As the automotive market is very dynamic and vehicle manufactures try to reduce the vehicle development cycle time, more focus is being given to CAE simulation technologies to reduce the design cycle time and number of physical tests. CAE engineers are continuously working on improving the accuracy of CAE simulation, such as using flexible body dynamic simulation in place of linear static analysis. Strength calculation under dynamic condition is more accurate as compared to static condition as it gives more clear understanding of stress variation with motion, contacts and mass inertia. Failure has been observed in new development of valve train pivot screw under test conditions. As per linear static analysis, design was judged OK. Normal linear static analysis is a two stage process. In first stage loads are calculated by hand or peak loads are taken from multibody dynamics (MBD) rigid body analysis.

The air pollution and global warming has become a major problem to the society. To counter this worldwide emission norms have become more stringent in recent times and shall continue to get further stringent in the next decade. From OEMs perspective with increased complexity, it has become a necessity to use simulation methods along with model based systems approach to deal with system level complexities and reduce model development time and cost to deal with the various regulatory requirements and customer needs. The simulation models must have good correlation with the actual test results and at the same time should be less complex, fast, and integrable with other vehicle function modelling. As the vehicle fuel economy is declared in cold start condition, the fuel economy simulation model of vehicle in cold start condition is required. The present paper describes a methodology to simulate the cold start fuel economy.

Automotive Industry is moving towards lightweight vehicle design with more powerful engines. This is increasing a demand for more optimized NVH design. Source-Path-Contributor (SPC) analysis is one of the ways to draw a holistic picture of any NVH problem. In this paper, an NVH problem of low frequency booming noise and steering vibration has been studied in a development vehicle. All three dimensions of SPC paradigm were looked at to propose a feasible and optimized solution at each level of Source, Path and Contributor model. A classical transfer path analysis (TPA) has been done to identify the highest contributing path: transmission mount and suspension arm. Optimization of suspension bush parameter has been carried out using dynamic elastomer testing facility for an improved NVH performance. After identifying source as engine a study of torsional fluctuations due to gas pressure and torsional resonances has been carried out in order to achieve a feasible solution at source.

With the development of automobile industry, customer awareness about NVH (Noise, Vibration and Harshness) levels in passenger vehicles and demands for improving the riding comfort has increased. This has prompted automobile OEMs to address these parameters in design stage by investing resources in NVH research and development for all components. Better NVH of Radiator Fan Module (RFM) is one of the parameters which contributes to cabin comfort. The basic objective of RFM is to meet engine heat rejection requirements with optimized heat transfer and air flow while maintaining NVH within acceptable levels. The rotating fan (generally driven by an electric motor), if not balanced properly, can be a major source of vibration in the RFM. The vibration generated thus, can be felt by customer through the vehicle body.

Shielding vehicle underbody or engine room components from exhaust heat is becoming a difficult task with increasing packaging constraints, which lead to the proximity of components with high temperatures of the exhaust systems. Heat insulators are provided to protect various components from exhaust system parts. Generally the requirement of heat insulators are fixed on the basis of benchmarked temperatures measured on vehicles with similar layout, during the initial phase of vehicle design. Also various CFD techniques are available to predict the surface temperatures on components in order to determine the necessity of a heat insulator. The aforementioned techniques use radiation and convection heat transfer effects on a complete vehicle model and the overall process generally takes considerable time to provide the results. This paper deals with a theoretical approach to predict the temperatures on nearby components due to exhaust system heat.

During vehicle development, numerous test are done to ensure safety & durability of the vehicle. One such test prescribed by regulation (IS 12009:1995) is side door intrusion test (SDIT). This test evaluates strength requirement of a side door of passenger cars to minimize the safety hazards caused by intrusion into passenger compartment in a side impact accident viz., initial, intermediate and peak crush resistance. In current scenario the passenger car manufacturers are striving hard on cost reduction by reducing the development cost. Thus, to predict the exact vehicle performance before its prototype stage is vital. This can be achieved by evaluating performance by the help of Computer aided engineering (CAE) During the SDIT, the load is applied to the outer surface of the door in an inward direction. This inward force applied by loading device is resisted by the door assembly, while door is pivoted at door latch and hinge.

Vehicles which are sold and put into service in a country have to meet the regulations and standards of that country. Every country has a separate regulation and approval procedure which requires expensive design modifications, additional tests and duplicating approvals. Thus, there is the need to harmonize the different national technical requirements for vehicles and form a unique international regulation. With this rationale, the World Forum for Harmonization of Vehicle Regulations of the United Nations Economic Commission for Europe (UN/ECE/WP29) has brought governments and automobile manufacturers together to work on a new harmonized test cycle and procedure which is to be adopted around the world. This lead to the development of Worldwide Harmonized Light Duty Test Procedures (WLTP) and Cycles (WLTC). The test procedure is divided into 3 cycles, depending on a power to mass ratio of the tested vehicle.

In the present automobile market, customers have put demand for smaller cars with better ride and comfort. For small diesel engine cars, where the comfort is known to be inferior to its gasoline siblings, the effect of engine excitation and road inputs has posed the problem of seat back vibrations. Low frequency vibrations are observed at irregular road inputs, which directly get transferred to the human body through the seat back resulting in fatigue and discomfort. This paper describes the use of testing and CAE in reducing the seat back vibrations. First step of the study includes the frequency response functions (FRF) of the seat frame and road data. The CAE model is validated with the test data and the problem areas are identified. The countermeasure design modifications in the seat frame structure are analyzed using CAE (Normal Mode Analysis). The feasible countermeasure action is road tested and clearly shows a reduction in the vibration levels coming on the seat back.