Search Results

Road accidents are a major concern worldwide and vulnerable road users make up more than half of the victims of road accident deaths. In order to combat this issue, several countries worldwide have mandated pedestrian safety test regulations viz., AIS100 & UN-R127. One of the requirements of the regulations is when Flexible Pedestrian Legform Impactor (Flex-PLI) is impacted onto the frontal structure of the vehicle at a speed of 40kmph, the Bending moment (BM) of tibia bone of Flex-PLI shall not exceed the regulatory limit of 340Nm. In this paper, we have built a statistical model for predicting the BM of tibia in Flex-PLI using regression analysis. 13 vehicles have been selected from all applicable vehicle categories viz., Sedan, hatchback, Coupe & SUV/MUV for this undertaking. An exhaustive analysis of the vehicle frontal structures and Flex-PLI test videos have been done to identify & measure the design parameters to be used as predictor variables.

With the advancement of regulatory norms in automobile industry, there is a challenge to meet performance efficiency targets, especially with a lightweight platform, while providing superior driving experience to customers. The shift towards weight optimization, makes the vehicle structure more susceptible to transfer a diverse range of noise and vibrations through body. Although most undesirable noises perceived inside the cabin can be reduced by superior technology engine mounts and NVH packaging, all such solutions lead to cost addition. Intelligent considerations in part design can be used to supplement predictable transfer paths to quell the unwanted vibrations. One such case is of the gear whine noise in certain rpm bands caused by inherent gear meshing frequency coinciding with natural frequency of an engine mounting bracket.

With the advent of upcoming stringent automobile emission norms globally, it is inevitable for original equipment manufacturers (OEMs) to shift towards greener alternatives. Use of compressed natural gas (CNG) is a preferred solution as it is a relatively clean burning fuel and it doesn’t have significant loss in vehicle efficiency and performance. Modern day customers are more aware and sensitive towards vehicle noise, vibration and harshness (NVH). Hence, OEMs must cater to this demand through optimized design and layout. In a passenger vehicle, CNG is stored at high pressure and delivered to injectors after pressure reduction at a regulator. During engine idling, the opening and closing motion of the CNG injector generates back pulsation and these pulsations cause vibrations which may propagate through other components in the delivery path and perceived as noise inside vehicle cabin.

As emissions standards become more stringent, OEMs are pushing engines to run on leaner fuel mixtures, which puts increased thermal stress on components, particularly pistons, causing them to operate at higher temperatures. This requires more robust design and rigorous testing of components. Telemetry methods offer accurate and real-time feedback, allowing designers to test components at various operating conditions, providing more flexibility than other traditional methods. Piston temperature measurement is a critical aspect of engine development because it directly affects engine performance and durability. Among the various techniques available for this purpose, telemetry methods have gained considerable attention in recent years. This method involves integrating temperature sensors and transmitter on the piston, which transmit temperature data wirelessly to a receiver outside the engine.

The advent of BS6 coupled with RDE emission norms has increased the development efforts and costs due to the shear amount of testing and validation on real engines and vehicles which are necessitated by these stringent norms. Front-loading of tasks by moving actual vehicle and engine tasks on to virtual setup, will reduce the development efforts and costs significantly. This front-loading of tasks on to a LABCAR would need real time and highly accurate plant models, tools to parameterize these plant models and accurate data driven models to predict dynamic parameters like emissions. In this collaborative work between Maruti Suzuki India Ltd and ETAS India, ETAS VVTB and ICE plant models were parameterized with the data generated on engine test with ASCMO Global DoE test plan by using ASCMO MOCA. The ASCMO Global test plan also ensures the coverage of data points across the entire engine operating space. These plants models were optimized to an accuracy level of more than 95%.

Various emission and fuel economy norms for passenger cars have been introduced by the government worldwide. In India, meeting each revision of the Bharat Stage (BS) emission standards and Corporate Average Fuel Economy (CAFE) norms is challenging, and requires the incorporation of new technologies into IC engines. One such technology used in gasoline engines is Exhaust gas recirculation (EGR). The entry of dust particles into the EGR system makes it vulnerable to malfunction. One such fleet validation challenge of EGR valve malfunction has been addressed in this study, where the EGR valve became stuck due to dust entry, leading to engine hunting and stalling. The approach followed for the issue resolution demonstrates a method of developing an EGR valve controller for simulating the failure on a bench setup. The controller setup was built around a microcontroller chip that accurately operated the valve with similar logic to that of the vehicle ECU.

Exhaust system of an automobile is primarily employed in automobile to purify exhaust gases and reduce noise due to combustion. However, a side-effect of the above function is the increase in backpressure. As specified in various literatures, an increase in backpressure can lead to a deterioration on engine performance (Power & torque). Benefit of backpressure reduction can be further taken in terms improving the power & torque of engine or improving the fuel economy. With growing concerns related to global warming and CO2 emissions, reducing exhaust back pressure is one of the promising areas in engine design in order to improve the fuel economy of the automobile and achieving carbon neutrality targets. However, reducing the back pressure generally tends to deteriorate the noise attenuation performance of the Exhaust system.

Recently, the Flexible Pedestrian Legform Impactor (or Flex-PLI) - an advancement over the existing EEVC legform - was included in the Global Technical Regulation for Pedestrian Safety viz. GTR-9. The legform tool undergoes impact testing with vehicle at 40kmph in order to evaluate the frontal structure of vehicle for Pedestrian Safety. Being more biofidelic design over the old EEVC legform, Flex-PLI is more flexible and sensitive towards different vehicle designs, shapes and inner bumper structure. This flexibility and sensitiveness of its design also calls for examining the Manufactured FlexPLI for its efficacy under impact testing in terms of its Durability, Repeatability and Reproducibility. This study aims at validating the performance of the test device by building a platform for computing the variations in test results. In this study, three key aspects are identified to measure the performance of this device - Durability, Repeatability, and Reproducibility.

In the modern automobile scenario in developing countries, customers are getting more meticulous and market more competitive. Now even the budget vehicle customer expects desirable vehicle performance in specific use cases of the vehicle that were previously not focused by designers. Hence, the focus on perceived quality challenges automobile engineers to go the extra mile when it comes to the cost-effective design of parts that are tangible to the customer. A vehicle's cowl cover is one such exterior component. The primary functions of this part are to provide air intake opening for the HVAC system and cover the components like wiper motor. The aesthetic function is to cover the gaps between windshield, hood, and fender as seamlessly as possible. A specific role of cowl cover, which calls for a designer's attention, is its load-bearing capability.

The outside visibility through the windshield and ORVM visibility through the side glasses are critical for safe driving. The frost deposition on the Windshield and side glasses in the cold climatic condition impairs the outside and ORVM visibility during driving and hence leads to an unsafe driving condition. In India, the regulation AIS-084 governs the defrosting standard. The defrosting performance evaluation by testing cannot be performed at concept stage when the vehicle prototype is not available. It also increases the cost of vehicle development due to increase in the number of prototype used for testing. This paper explains about the in-house developed CFD methodology to evaluate the windshield defrosting performance of the vehicle in the concept stage when no vehicle proto is available and cost of countermeasure for defrosting performance improvent is very less. This methodology is implemented for some of the existing models.

In manual transmission vehicles, Clutch has direct interaction with the driver and plays a significant role in defining the drivability and NVH of a vehicle. These key performance factors depend on the interaction of diaphragm and cushion springs of a clutch. For an automobile manufacturer, it’s essential to optimize the characteristics of these springs based vehicle performance requirements. A state of the art analytical model has been developed by modeling the diaphragm and cushion spring with exponential equations. Based on these models, response functions for release load, torque build-up, and pressure plate lift have been derived. Results achieved from these response functions are correlated with test data. Key contributing factors for peak clutch pedal load, vehicle launch acceleration, and disengagement point have been identified by sensitivity analysis. Multi-objective optimization is performed to select optimized parameters for vehicle performance improvement

Use of safety belts inside a vehicle is necessary to ensure the safety of passengers as well as drivers. To promote the use of seat belts, a seatbelt reminder system is utilized. This system incorporates a sensor for checking seat occupancy for the passenger seat. Activation of these sensors depends on various parameters like seat pad shape, seat upholstery, vehicle H-point, a load on the seat, etc. In this study, the load factor on the seat is studied. The load on the seat may come from occupants or due to the objects placed on the seat. The detection of objects as an occupant may result in false seat belt reminder alarm and cause inconvenience to the customers. Subjective analysis and surveys, covering a broad range of market population, were done to identify such objects. Consequently, performance requirements were determined to facilitate sensor optimization and selection.

In laboratory car crash tests, Anthropomorphic Test Devices (ATD) are equipped with piezoresistive and resistive sensors for occupant injury assessment. Accelerometers are inertial transducers that convert acceleration into electrical output which can be easily recorded by a Data Acquisition System (DAS). For an accelerometer, this electrical output mainly depends upon subjected acceleration, sensitivity of the accelerometer, excitation voltage and gain provided. Before use in testing, accelerometers are calibrated at a standard excitation (manufacturer decided) voltage to determine characteristics like Sensitivity, Sensitivity per unit excitation voltage, Zero Measurand Output (ZMO), Transverse Sensitivity etc. It is observed that these characteristics are highly dependent on the excitation voltage. In testing, due to limitations of DAS and/or other unwanted noise in the excitation voltage, these accelerometers are sometimes used at a different excitation voltage.

Clutch actuation system in manual transmission is one of the key systems of power-train with which driver interacts frequently. Therefore its load and travel feeling are important to customer. Clutch actuation system consists of clutch pedal assembly, flexible cable mounted on body panel, and clutch release arm/ shaft assembly inside transmission unit assembly. Clutch pedal load, travel and engagement point are important parameters to specify the actuation feeling while designing the clutch actuation system. Validation of actual values is being done at proto vehicle testing stage, as final output calculation may not be accurate due to dependency on variables difficult to estimate. To overcome these difficulties a virtual dynamic model of the entire clutch actuation mechanism has been created in MBD software. Model input factors are based on actual testing results to improve the accuracy. The model predicts the clutch pedal load and travel values for a given set of vehicle inputs.

During the conceptualization of vehicle, it is big challenge for automotive manufacturer to design a vehicle which has an excellent aesthetic looks as well as meet the stringent vehicle regulations. In the vehicle styling, bumper plays an important role in deciding of the contemporary looks of the vehicle. To improve customer satisfaction, it is important to design a bumper which provides feeling and sense of durability. In addition, bumper should sustain low-speed impact and protects the peripheral components such as parking lights, headlamps, hood, back door and safety related installed equipments like Rear parking camera, parking sensors, etc. Bumper should be dent resistant and be able to regain its original shape on removal of the applied load. An elegant design of bumper should be light weight with high strength. This paper explains about a new CAE methodology developed to simulate the real life loading condition of bumper and to calculate the deformation in the bumper.

The automobile market is witnessing a different trend altogether - the trend of shifting preference from powerful to fuel efficient machines. Certain factors like growing prices of fuel, struggling global economy, environmental sensitiveness and affordability have pushed the focus on smaller, efficient and cleaner automobiles. To meet such requirements, the automobile manufacturers, are going stringent on vehicle weights. Using electric and hybrid power-plants are other options to meet higher fuel efficiency and emission requirements but significant cost of these technologies have kept their growth restricted to only few makers and to only few regions of the globe. Optimizing the vehicle weight is a more attractive option for makers as it promises lesser time to market, is low on investment and allows use of existing platforms.

Offset crash compliance of a compact car is severe due to the compact layout and stringent fuel economy, weight and cost targets. Scope of the current work is to improve the structural crash performance of a compact car through CAE, in order to meet the offset frontal crash requirements as per ECE R94 Regulation. The project has been classified in three main phases. First phase includes the evaluation of baseline vehicle in CAE. In order to ensure the accuracy of CAE prediction, a methodology for predicting Spotweld rupture was implemented. Using this methodology, it is possible to find out the location and time of spotweld rupture as well as propagation of spotweld rupture in CAE. CAE results of spotweld rupture prediction showed good agreement with the physical test. In second phase, design iterations were carried out in order to meet the performance targets of structural deformation.

Front end accessory drive (FEAD) system explained in this paper is a sub-system of an engine. In FEAD system, a poly-v belt is used to drive the alternator and water pump by transmitting power from crankshaft pulley. In a new vehicle development program, durability targets of FEAD system are based on required life of poly-v belt, its static tension readjustment interval and replacement frequency. To meet these durability targets following methodology is applied in design stage:- 1 Simulation of FEAD system to calculate the theoretical life of belt 2 Part level testing of belt as per SAE J2432 These methods give sufficient information on belt durability. However in actual usage, certain failures are prone to happen and enormous difference is always observed between theoretical and actual life of belt. This paper describes the traditional stair-case approach followed to optimize the FEAD system based on the outcome of durability tests.

The side impact accident is one of the very severe crash modes for the struck side occupants. According to NHTSA fatality reports, side impact accounts for over 25% of the fatalities in the US. Similar fatality estimates have been reported in the EU region. Side crash compliance of a compact car is more severe because of the less space available between the occupant and the vehicle structure, stringent fuel economy, weight and cost targets. The current work focuses on the development of Side body structure of a compact car through Computer Aided Tools (CAE), for meeting the Side crash requirements as per ECE R95 Regulation. A modified design philosophy has been adopted for controlling the intrusion of upper and lower portion of B-pillar in order to mitigate the injury to Euro SIDII dummy. At first, initial CAE evaluation of baseline vehicle was conducted.

The durability evaluation of overhanging components of a vehicle (Ex: horn, radiator) is a challenge to durability engineers as resonance plays an important role in determining their fatigue life. As resonance cannot be avoided always, it is desirable to develop methods to evaluate life of the component in the presence of resonance. Though the existing vibration test standards suggest test profiles to evaluate resonance failures, there are cases in which, these methods do not yield the proving ground results. This may lead to unnecessary overdesign or unrealistic failures. In such cases it is suggested to generate a sweep endurance test procedure customized to the proving ground or actual roads. This paper studies a methodology for generating a sweep endurance test procedure for evaluation of resonating components. Responses like stress and accelerations were measured in test components in proving ground. Contribution of each frequency band towards overall damage is determined.