Search Results

Surface coatings are one of the most widely used routes to enhance the tribological properties of cylinder kits due to effective sealing capability with low friction coefficient and high wear resistance. In the current study, we have conducted the surface texture characterization of the coating on piston skirts and evaluated the impact of a novel Abradable Powder Coating (APC) on cylinder-kit performance in comparison to stock pistons. The surface texture and characteristic properties varying across the piston skirt are obtained and analyzed via a 3D optical profiler and OmniSurf3D software. The engine operating conditions are found through a combination of measurements, testing, and a calibrated GT-Power model. The variable surface properties along with other dimensions, thermodynamic attributes, flow characteristics and material properties are used to build a model in CASE (Cylinder-kit Analysis System for Engines)- PISTON for both an APC coated piston and a stock piston.

Rapid Compression Machines (RCM) offer the ability to easily change the compression ratio and the pressure/mixture composition/temperature to gather ignition delay data at various engine relevant conditions. Therefore, RCMs with optical access to the combustion chamber can provide an effective way to analyze macroscopic spray characteristics needed to understand the spray injection process and for spray model development, validation and calibration at conditions that are suitable for engines. Fuel surrogates can help control fuel parameters, develop models for spray and combustion, and perform laser diagnostics with known fluorescence characteristics. This study quantifies and evaluates the macroscopic spray characteristics of multicomponent gasoline surrogates in comparison to their gasoline counterparts, under gasoline direct injection (GDI) engine conditions.

Understanding cylinder-kit tribology is pivotal to durability, emission management, reduced oil consumption, and efficiency of the internal combustion engine. This work addresses the understanding of the fundamental aspects of oil transport and combustion gas flow in the cylinder kit, using simulation tools and high-performance computing. A dynamic three-dimensional multi-phase, multi-component modeling methodology is demonstrated to study cylinder-kit assembly tribology during the four-stroke cycle of a piston engine. The percentage of oil and gas transported through different regions of the piston ring pack is predicted, and the mechanisms behind this transport are analyzed. The velocity field shows substantial circumferential flow in the piston ring pack, leading to blowback into the combustion chamber during the expansion stroke.

The fluid motion inside the engine cylinder is transient, three-dimensional and highly turbulent. It is also well known that cycle-to-cycle flow variations have a considerable influence on cycle-to-cycle combustion variations. Laser-based diagnostic techniques, for example, particle image velocimetry (PIV) or molecular tagging velocimetry, can be used to measure two or three components of the velocity field simultaneously at multiple locations over a plane. The use of proper orthogonal decomposition (POD) allows quantification of cycle-to-cycle flow variations, as demonstrated using PIV data [1]. In the present work, POD is used to explore the cycle-to-cycle flow variations utilizing molecular tagging velocimetry data. The instantaneous velocity fields were obtained over a swirl measurement plane when engine was operated at 1500 rpm and 2500 rpm.

An auxiliary fueled prechamber ignition system can be used in an IC engine environment to provide lean limit extension with minimal cyclic variability and low emissions. Geometry and distribution of the prechamber orifices form an important criterion for performance of these systems since they are responsible for transferring and distributing the ignition energy into the main chamber charge. Combustion performance of nozzles with a single jet, dual diverging jets and dual converging jets for a methane fueled prechamber ignition system is evaluated and compared in a rapid compression machine (RCM). Upon entering the main chamber, the dual diverging jets penetrate the main chamber in opposite directions creating two jet tips, while the dual converging jets, after exiting the orifices, converge into a single location within the main chamber. Both these configurations minimize jet-wall impingement compared to the single jet.

As the variable nozzle turbine(VNT) becomes an important element in engine fuel economy and engine performance, improvement of turbine efficiency over wide operation range is the main focus of research efforts for both academia and industry in the past decades. It is well known that in a VNT, the nozzle endwall clearance has a big impact on the turbine efficiency, especially at small nozzle open positions. However, the clearance at hub and shroud wall sides may contribute differently to the turbine efficiency penalty. When the total height of nozzle clearance is fixed, varying distribution of nozzle endwall clearance at the hub and shroud sides may possibly generate different patterns of clearance leakage flow at nozzle exit that has different interaction with and impact on the main flow when it enters the inducer.

Camless Variable Valve Actuation (VVA) technologies have been known for improving fuel economy, reducing emissions, and enhancing engine performance. VVA can be divided into electro-magnetic, electro-hydraulic, and electro-pneumatic actuation. This paper presents an electro-hydraulic VVA design (called GD-VVA-2) that offers continuously variable timing and two discrete lifts (low lift S1 and high lift S2). The lift control is achieved through a lift control sleeve, which is hydraulically switched between two mechanically defined positions to provide accurate lifts. The low lift S1 has a wide design range, anywhere between zero and the high lift S2, i.e., 0 < S1 < S2. If S1 ≥ 0.5*S2, engine valves may operate at the low lift during most of a typical drive cycle. Operation at the low lift reduces energy consumption significantly. The GD-VVA-2 design offers compact package size and reasonable energy consumption.

Camless Variable Valve Actuation (VVA) technologies have been known for improving fuel economy, reducing emissions, and enhancing engine performance. VVA can be divided into electro-magnetic, electro-hydraulic, and electro-pneumatic actuation. A family of camless VVA designs (called LGD-VVA or Gongda-VVA) has been presented in an earlier SAE publication (SAE 2007-01-1295) that consists of a two-spring actuation, a bypass passage, and an electrohydraulic latch-release mechanism. The two-spring pendulum system is used to provide efficient conversion between the moving mass kinetic energy and the spring potential energy for reduced energy consumption and to be more robust to the operational temperature than the conventional electrohydraulic actuation; and the electrohydraulic mechanism is intended for latch-release function, energy compensation and seating velocity control.

Three-dimensional transient simulations using KIVA-3V were conducted on a 4-stroke high-compression ratio, methanol-fueled, direct-injection (DI) engine. The engine had two intake ports that were designed to impart a swirling motion to the intake air. In some cases, the intake system was modified, by decreasing the ports diameter in order to increase the swirl ratio. To investigate the effect of adding shrouds to the intake valves on swirl, two sets of intake valves were considered; the first set consisted of conventional valves, and the second set of valves had back shrouds to restrict airflow from the backside of the valves. In addition, the effect of using one or two intake ports on swirl generation was determined by blocking one of the ports.

In an effort to create computer models to promote rapid, cost-effective prototyping while easing design changes, more information about how people interact with seats is needed. Predicting the occupant location, their geometry, and motion within a vehicle leads to a better determination of safety restraint location, controls reach, and visibility - factors that affect the overall operation of the vehicle. Based on the Michigan State University JOHN model, which provides a biomechanical simulation of the torso posture, experiments were conducted to examine the change of postures due to seat and interior package factors. The results can be incorporated into the posture prediction model of the RAMSIS program to give a more detailed prognosis of the spine curvature and refine the model-seat interactions. This paper will address findings of the experimental study with relation to model development.

This paper describes additional and more recent results from the DaimlerChrysler study of HANS that includes a sensitivity analysis of HANS performance to variations in crash dummy neck length and other impact test conditions. The objective of the tests was to determine the robustness of the HANS concept in a variety of conditions that might occur in actual use. The results show that the variations in test parameters do effect injury measures from the crash dummy, but HANS provides substantial reductions in injury potential in all cases compared to not using HANS. Also, no injuries were indicated with HANS.

Extensive crash sled testing and analysis has recently led to the development of a new HANS prototypes for use in FIA F1. The performance of HANS prototypes has been studied with various conditions of HANS design geometry and impact direction. The new HANS prototypes have been found to substantially reduce injurious motions and forces of the head and neck, and the new HANS is lighter, more compact, and performs better than the currently available HANS. Use of HANS by FIA F1 drivers has been initiated.

Injuries to the lower extremities are common during car accidents because the lower extremity is typically the first point of contact between the occupant and the car interior. While injuries to the knee, ankle and hip are usually not life threatening, they can represent a large societal burden through treatment costs, lost work days and a reduced quality of life. The aim of the current study was to specifically study injuries associated with the knee and to propose a methodology which could be used to prevent future knee injuries. To understand the scope of this problem, a study was designed to identify injury trends in car crashes for the years 1979-1995. The NASS (National Accident Sampling System) showed that 10% of all injuries were to the knee, second only to head and neck injuries. Most knee injuries resulted from knee-to-instrument panel contact. Subfracture injuries were most common (contusions, abrasions, lacerations) followed by gross fracture injuries.

Since the 1960's, automotive seats have been designed and evaluated with tools and procedures described in the SAE Recommended Practice J826. The SAE J826 design template and testing manikin each have a torso with a flat lower back shape and with a single joint at the H-point. The JOHN models provide a more anatomically detailed representation of human shape and movement. The articulations of the JOHN torso (pelvic, lumbar, and thoracic) segments are coupled so that their relative positions are determined by a single parameter related to spinal curvature. This paper describes the development and use of the JOHN biomechanical models for seating design.

Lower extremity (knee) injury prediction resulting from impact trauma is currently based on a bone fracture criterion derived from experiments on predominantly aged cadavers. Subsequent experimental and theoretical studies indicate that more aged, pathological specimens require higher, not lower, loads to initiate bone fracture. This suggests that a bone fracture criterion based solely on aged specimens may not be representative of the current driving population. In the current study, we sought to determine if cadaver age, physical size, sex, baseline joint pathology, or patellar geometry correlated with fracture load. An analysis was made of data from previous impact experiments conducted on fifteen isolated cadaver knees using a consistent impact protocol. The protocol consisted of sequentially increasing the impact energy with a rigid interface until gross fracture. Gross bone fractures occurred at loads of 6.9±2.0 kN (range 3.2 to 10.6 kN) using this protocol.

Injury to the lower extremity during an automotive crash is a significant problem. While the introduction of safety features (i.e. seat belts, air bags) has significantly reduced fatalities, lower extremity injury now occurs more frequently, probably for a variety of reasons. Lower extremity trauma is currently based on a bone fracture criterion derived from human cadaver impact experiments. These impact experiments, conducted in the 1960's and 70's, typically used a rigid impact interface to deliver a blunt insult to the 90° flexed knee. The resulting criterion states that 10 kN is the maximum load allowed at the knee during an automotive crash when certifying new automobiles using anthropomorphic dummies. However, clinical studies suggest that subfracture loading can cause osteochondral microdamage which can progress to a chronic and debilitating joint disease.

The human torso includes three major segments, the thoracic (rib cage) segment, lumbar segment, and pelvic segment to which the thighs are attached. The JOHN model was developed to represent the positions and movements of these torso segments along with the head, arms, and legs. Using the JOHN model, a new seat concept has been developed to support and move with the torso segments and thighs. This paper describes the background of the biomechanically articulated chair (BAC) and the development of BAC prototypes. These BAC prototypes have been designed to move with and support the thighs, pelvis, and rib cage through a wide variety of recline angles and spinal curvatures. These motions have been evaluated with computer modeling and with initial experience of human subjects. Results from computer modeling and human subjects show that the BAC will allow a broad range of torso postures.

This paper presents results from experiments performed in an axisymmetric water analog model of a four-stroke IC engine using the optical velocimetry technique LIPA (Laser Induced Photochemical Anemometry). The investigation can be described as a fundamental scientific inquiry into the fluid dynamics encountered during engine operation, with the long term goal of increasing performance. An application of LIPA to a fluid dynamics problem delivers two-dimensional fields of velocity vectors which are projections of the full three-dimensional vectors in single measurement steps. From an evaluation of a velocity field vorticity information can be obtained readily. Velocity fields and vorticity distributions are, in this study, the basis for the evaluation of seven parametric quantities. Some of these may become tools that give engineers ‘rule of thumb’ indications of the mixing that is occurring.

This paper presents a review of the core functions and decisions of transportation and traffic management in the automobile industry. Its purpose is to present the concepts within a revised framework which is set in a logistical channels context. Using this approach it easier to see the interdependence which is necessary between shippers and carriers that handle raw materials, component parts, and finished products.