Search Results

This paper documents the vehicle response of a tractor-semitrailer following a sudden air loss (Blowout) in a steer axle tire while traveling at highway speeds. The study seeks to compare full-scale test data to predicted response from detailed heavy truck computer vehicle dynamics simulation models. Full-scale testing of a tractor-semitrailer experiencing a sudden failure of a steer axle tire was conducted. Vehicle handling parameters were recorded by on-board computers leading up to and immediately following the sudden air loss. Inertial parameters (roll, yaw, pitch, and accelerations) were measured and recorded for the tractor and semitrailer, along with lateral and longitudinal speeds. Steering wheel angle was also recorded. These data are presented and also compared to the results of computer simulation models. The first simulation model, SImulation MOdel Non-linear (SIMON), is a vehicle dynamic simulation model within the Human Vehicle Environment (HVE) software environment.

An ignition delay correlation was developed for a toluene reference fuel (TRF) blend that is representative of automotive gasoline fuels exhibiting two-stage ignition. Ignition delay times for the autoignition of a TRF 91 blend with an antiknock index of 91 were predicted through extensive chemical kinetic modeling in CHEMKIN for a constant volume reactor. The development of the correlation involved determining nonlinear least squares curve fits for these ignition delay predictions corresponding to different inlet pressures and temperatures, a number of fuel-air equivalence ratios, and a range of exhaust gas recirculation (EGR) rates. In addition to NO control, EGR is increasingly being utilized for managing combustion phasing in spark ignition (SI) engines to mitigate knock. Therefore, along with other operating parameters, the effects of EGR on autoignition have been incorporated in the correlation to address the need for predicting ignition delay in SI engines operating with EGR.

Plug in hybrid electric vehicles (PHEVs) have gained interest over last decade due to their increased fuel economy and ability to displace some petroleum fuel with electricity from power grid. Given the complexity of this vehicle powertrain, the energy management plays a key role in providing higher fuel economy. The energy management algorithm on PHEVs performs the same task as a hybrid vehicle energy management but it has more freedom in utilizing the battery energy due to the larger battery capacity and ability to be recharged from the power grid. The state of charge (SOC) profile of the battery during the entire driving trip determines the electric energy usage, thus determining overall fuel consumption.

The EcoCAR Challenge team at The Ohio State University has designed an extended-range electric vehicle capable of 50 miles all-electric range via a 22 kWh lithium-ion battery pack, with range extension and limited parallel operation supplied by a 1.8 L dedicated E85 engine. This vehicle is designed to drastically reduce fuel consumption, while meeting Tier II Bin 5 emissions standards. This vehicle design is implemented in a GM crossover utility vehicle as part of the EcoCAR Challenge. This paper explains the implementation of the vehicle's control strategy in order to maintain high efficiency and improve drivability. The vehicle control strategy employs both distinct operating modes and an Equivalent Consumption Minimization Strategy (ECMS) to find the most efficient operating point. The ECMS strategy does an online search for the most efficient torque split in order to meet the driver's command.

Torsional stiffness properties were developed for both a 53-foot box trailer and a 28-foot flatbed control trailer based on experimental measurements. In order to study the effect of torsional stiffness on the dynamics of a heavy truck vehicle dynamics computer model, static maneuvers were conducted comparing different torsional stiffness values to the original rigid vehicle model. Stiffness properties were first developed for a truck tractor model. It was found that the incorporation of a torsional stiffness model had only a minor effect on the overall tractor response for steady-state maneuvers up to 0.4 g lateral acceleration. The effect of torsional stiffness was also studied for the trailer portion of the existing model.

Two-stage turbochargers are a recent solution to improve engine performance, reducing the turbo-lag phenomenon and improving the matching. However, the definition of the control system is particularly complex, as the presence of two turbochargers that can be in part operated independently requires effort in terms of analysis and optimization. This work documents a characterization study of two-stage turbocharger systems. The study relies on a mean-value model of a Diesel engine equipped with a two-stage turbocharger, validated on experimental data. The turbocharger is characterized by a VGT actuator and a bypass valve (BPV), both located on the high-pressure turbine. This model structure is representative of a “virtual engine”, which can be effectively utilized for applications related to analysis and control. Using this tool, a complete characterization was conducted considering key operating conditions representative of FTP driving cycle operations.

In 2007, a software model of a Roll Stability Control (RSC) system was developed based on test data for a Volvo tractor at NHTSA's Vehicle Research and Test Center (VRTC). This model was designed to simulate the RSC performance of a commercially available Electronic Stability Control (ESC) system. The RSC model was developed in Simulink and integrated with the available braking model (TruckSim) for the truck. The Simulink models were run in parallel with the vehicle dynamics model of a truck in TruckSim. The complete vehicle model including the RSC system model is used to simulate the behavior of the actual truck and determine the capability of the RSC system in preventing rollovers under different conditions. Several simulations were performed to study the behavior of the model developed and to compare its performance with that of an actual test vehicle equipped with RSC.

Validation was performed on an existing heavy truck vehicle dynamics computer model with roll stability control (RSC). The first stage in this validation was to compare the response of the simulated tractor to that of the experimental tractor. By looking at the steady-state gains of the tractor, adjustments were made to the model to more closely match the experimental results. These adjustments included suspension and steering compliances, as well as auxiliary roll moment modifications. Once the validation of the truck tractor was completed for the current configuration, the existing 53-foot box trailer model was added to the vehicle model. The next stage in experimental validation for the current tractor-trailer model was to incorporate suspension compliances and modify the auxiliary roll stiffness to more closely model the experimental response of the vehicle. The final validation stage was to implement some minor modifications to the existing RSC model.

This paper describes a method to evaluate vehicle stability and controllability when the vehicle operates in the nonlinear range of lateral dynamics. The method is applied to open-loop steering maneuvers as well as closed-loop path-following maneuvers. Although path-following maneuvers are more representative of real world driving intent, they are usually considered inappropriate for objective assessment because of repeatability and accuracy issues. The automated test driver (ATD) can perform path-following maneuvers accurately and with good repeatability. This paper discusses the usefulness of application of the automated test drivers and path-following maneuvers. The dynamic mode of instability is not directly obtained from measurable outputs such as yawrate and lateral acceleration as in open-loop maneuvers. A few metrics are defined to quantify deviation from desired or ideal behavior in terms of observed “unexpected” lateral force and moment.

ORVR (Onboard Refueling Vapor Recovery) canisters trap vapors during normal operations of a vehicle's engine, and during refueling. This study evaluates the relative risks involved should a canister rupture in a crash. A canister impactor was developed to simulate real-world impacts and to evaluate the canisters' rupture characteristics. Numerous performance aspects of canisters were evaluated: the energy required to rupture a canister; the spread of carbon particles following rupture; the ease of ignition of vapor-laden particles; the vapor concentration in the area of ruptured, vapor-laden canisters; and the potential of crashes to rupture and ignite canisters. Results from these five items were combined into a risk analysis.

This paper presents a concept for enhancing catalytic removal of pollutant species from an exhaust stream by placing placing the plasma adjacent to the catalyst surface. Model calculations of the behavior of the electron energy distribution function (EEDF), which influences the chemistry and ionization levels near the surface, are performed and analyzed. Preliminary experiments attempting to reduce these theoretical ideas to practice in N2/NO mixtures, are discussed. Although removal of NO is observed, this is due to gas phase effects alone. The present experimental arrangement is not able to produce the requisite conditions outlined by theory to enact plasma-enhanced catalysis.

The evolution of the diagnostic equipment for automotive application is the direct effect of the implementation of sophisticated and high technology control systems in the new generation of passenger cars. One of the most challenging issues in automotive diagnostics is the ability to assess, to analyze, and to integrate all the information and data supplied by the vehicle's on-board computer. The data available might be in the form of fault codes or sensors and actuators voltages. Moreover, as environmental regulations get more stringent, knowledge of the concentration of different species emitted from the tailpipe during the inspection and maintenance programs can become of great importance for an integrated powertrain diagnostic system. A knowledge-based diagnostic tool is one of the approaches that can be adopted to carry out the challenging task of detecting and diagnosing faults related to the emissions control system in an automobile.

A number of automotive diagnostic equipment and procedures have evolved over the last two decades, leading to two generations of on-board diagnostic requirements (OBDI and OBDII), increasing the number of components and systems to be monitored by the diagnostic tools. The goal of On-Board Diagnostic is to alert the driver to the presence of a malfunction of the emission control system, and to identify the location of the problem in order to assist mechanics in properly performing repairs. The aim of this paper is to suggest a methodology for the development of an Integrated Powertrain Diagnostic System (EPDS) that can combine the information supplied by conventional tailpipe inspection programs with onboard diagnostics to provide fast and reliable diagnosis of malfunctions.

The soil response to traffic loads as affected by tire inflation pressure, track width and drawbar pull was measured. The change in soil physical properties caused by a John Deere 8870 tractor at two tire pressure settings and CATERPILLAR Challenger 65 and 75 tractors with 64 and 89 cm wide belt tracks, were measured at two load levels; no draft (tractor only) and tractor pulling a 12.5 m field cultivator. The Ohio State University Soil Physical Properties Measurement System was used to measure cone penetration resistance, air permeability, air-filled porosity, and bulk density. The results show the dual overinflated tires caused the greatest change, followed by the CATERPILLAR Challenger 65 track, then the CATERPILLAR Challenger 75 track, and finally dual correctly inflated tires caused the least effect on soil physical properties. These results were consistent at each depth. The effects of the two draft levels give the same ranking of the tractive units.

Soil response to differences in tire size and inflation pressure was measured for a JD 9600 combine with 18.4R38 dual tires, 30.5L32 single tires, 68x50.00-32 single tires at 103 and 166 kPa inflation pressure and a John Deere half-track system on two different soils (Kokomo and Crosby) near Urbana, Ohio. A loaded 42.3 m3 grain cart was included on the Kokomo soil for comparative purposes. The Ohio State Soil Physical Properties Measurement System was used to sample and measure the bulk density, air-filled porosity, air permeability and cone penetration resistance between 10 and 50 cm depths. The results for Kokomo soil show the grain cart had the greatest effect with an average decrease in total porosity of 12.90 percent, compared to 7.95%, 6.05%, 4.56%, 3.06%, and 2.04% for singles, tracks, duals, wide overinflated, and wide rated pressure tires, respectively, on the combine.

One of the gray areas in the implementation of regulations limiting the generation of pollutants from mobile sources is the actual effectiveness of the exhaust gas emissions control strategy in vehicles that have been in use for some time. While it is possible today to conduct limited diagnostics with the on-board engine computer by performing periodic checks to verify the validity of the signals measured by the on-board sensors, and to measure tailpipe emissions during routine inspection and maintenance, the task of correlating these measurements with each other to provide an on-line, accurate diagnosis of critical malfunctions has thus far proven to be a very challenging task, especially in the case of misfire.

Flow fields generated during the intake stroke of a 4-stroke I.C. engine are studied experimentally using water analog simulation. The fluid is seeded by small flow tracer particles and imaged by two digital cameras at BDC. Using a 3-D Particle Tracking Velocimetry technique recently developed, the 3-D motion of these flow tracers is determined in a completely automated way using sophisticated image processing and PTV algorithms. The resulting 3-D velocity fields are ensemble averaged over a large number of successive cycles to determine the mean characteristics of the flow field as well as to estimate the turbulent fluctuations. This novel technique was applied to three different cylinder head configurations. Each configuration was run for conditions simulating idle operation two different ways: first with both inlet ports open and second with only the primary port open.

The introduction of advanced electronic controls in passenger vehicles over the last decade has made traditional diagnostic methods inadequate to satisfy on- and off-board diagnostic needs. Due to the complexity of today's automotive control systems, it is imperative that appropriate diagnostic tools be developed that are capable of satisfying current and projected service and on-board requirements. The performance of available diagnostic and test equipment is still amenable to further improvement, especially as it pertains to the diagnosis of incipient and intermittent faults. It is our contention that significant improvement is possible in these areas. This paper briefly summarizes the evolution of on- and off-board diagnostic tools documented in the published literature, with the aim of giving the reader an understanding of their capabilities and limitations, and it further proposes alternative solutions that may be adopted as a basis for an advanced diagnostic instrument.

The objective of this paper is to develop a self-tuning optimal control of an active suspension. An active suspension composed of an identifier and a controller is proposed in this paper. Although control strategies on active (or semi-active) suspensions have been investigated during the past few decades, some problems are not well understood yet. One of them arising from the ride control of an active suspension is that when the weight and the moments of inertia of the sprung mass are varied, the feedback gains of the controller should vary with the variation of parameters accordingly. Therefore, the identifier is proposed before the controller is designed. In the real situations, the parameter variation may occur when loadings on vehicles vary - either from passengers or payloads, especially, in the case of loading on a truck. An identification structure using parallel model reference adaptive system (MRAS) is proposed to identify the true parameters.