Search Results

Assuming rigid body motion, recorded acceleration and recorded roll rates at the center of gravity, equations are used to calculate the local three-dimensional accelerations at hypothetical seating positions' Emergency Locking [seat belt] Retractors (ELR) during a steer induced rollover crash. For a threshold of 0.7 g, results demonstrated that intervals in the vehicle's response that may cause the ELR's inertial sensor to move into a neutral zone were limited to localized high magnitude negative vertical acceleration events during the rollover segment with a median duration of 4 ms, average duration of 4.8 ms and a maximum calculated duration of 31.7 ms. Changing the threshold to 0.35 g reduced the interval count by 70 percent and maximum duration by approximately 50 percent.

This paper presents a feedback linearization control technique as applied to a Roll Simulator. The purpose of the Roll Simulator is to reproduce in-field rollovers of ROVs and study occupant kinematics in a laboratory setting. For a system with known parameters, non-linear dynamics and trajectories, the feedback linearization algorithm cancels out the non-linearities such that the closed-loop dynamics behave in a linear fashion. The control inputs are computed values that are needed to attain certain desired motions. The computed values are a form of inverse dynamics or feed-forward calculation. With increasing system eigenvalue, the controller exhibits greater response time. This, however, puts a greater demand on the translational actuator. The controller also demonstrates that it is able to compensate for and reject a disturbance in force level.

Objectives. Examination of head injuries in the Pedestrian Crash Data Study (PCDS) indicates that many pedestrian head injuries are induced by a combination of head translation and rotation. The Simulated Injury Monitor (SIMon) is a computer algorithm that calculates both translational and rotational motion parameters relatable head injury. The objective of this study is to examine how effectively HIC and three SIMon correlates predict the presence of either their associated head injury or any serious head injury in pedestrian collisions. Methods. Ten reconstructions of actual pedestrian crashes documented by the PCDS were conducted using a combination of MADYMO simulations and experimental headform impacts. Linear accelerations of the head corresponding to a nine-accelerometer array were calculated within the MADYMO model's head simulation.

Liver trauma research suggests that rapidly increasing internal pressure plays a role in liver injury. Previous work has shown a correlation between pressure and liver injury in pressurized ex vivo human livers when subjected to blunt impacts. The purpose of this study was to extend the investigation of this relationship between pressure and liver injury by testing full-body post-mortem human surrogates (PMHS). Pressure-related variables were compared with one another and also to previously proposed biomechanical predictors of abdominal injury. Ten PMHS were tested. The abdominal vessels were pressurized to physiological levels using saline, and a pneumatic ram impacted the right side of the specimen ribcage at a nominal velocity of 7.0 m/s. Specimens were subjected to either lateral (n = 5) or oblique (n = 5) impacts, and the impact-induced pressures were measured by transducers inserted into the hepatic veins and inferior vena cava.

In ISO Technical Report 9790 (1999) normalized lateral and oblique thoracic force-time responses of PMHS subjected to blunt pendulum impacts at 4.3 m/s were deemed sufficiently similar to be grouped together in a single biomechanical response corridor. Shaw et al., (2006) presented results of paired oblique and lateral thoracic pneumatic ram impact tests to opposite sides of seven PMHS at sub-injurious speed (2.5 m/s). Normalized responses showed that oblique impacts resulted in more deflection and less force, whereas lateral impacts resulted in less deflection and more force. This study presents results of oblique and lateral thoracic impacts to PMHS at higher speeds (4.5 and 5.5 m/s) to assess whether lateral relative to oblique responses are different as observed by Shaw et al., or similar as observed by ISO.

In order to evaluate a human surrogate, the human and surrogate response must be defined. The purpose of this study was to evaluate the response of cadaver subjects to blunt impacts to the frontal bone, nasal bone and maxilla. Force-displacement corridors were developed based on the impact response of each region. Variation in the force-displacement response of the cadaver subjects due to the occurrence of fracture and fracture severity was demonstrated. Additionally, impacts were performed at matched locations using the Facial and Ocular CountermeasUre Safety (FOCUS) headform. The FOCUS headform is capable of measuring forces imposed onto facial structures using internal load cells. Based on the tests performed in this study, the nasal region of the FOCUS headform was found to be the most sensitive to impact location. Due to a wide range in geometrical characteristics, the nasal impact response varied significantly, resulting in wide corridors for human response.

In 2007, a software model of a Roll Stability Control (RSC) system was developed based on test data for a Volvo tractor at NHTSA's Vehicle Research and Test Center (VRTC). This model was designed to simulate the RSC performance of a commercially available Electronic Stability Control (ESC) system. The RSC model was developed in Simulink and integrated with the available braking model (TruckSim) for the truck. The Simulink models were run in parallel with the vehicle dynamics model of a truck in TruckSim. The complete vehicle model including the RSC system model is used to simulate the behavior of the actual truck and determine the capability of the RSC system in preventing rollovers under different conditions. Several simulations were performed to study the behavior of the model developed and to compare its performance with that of an actual test vehicle equipped with RSC.

Validation was performed on an existing heavy truck vehicle dynamics computer model with roll stability control (RSC). The first stage in this validation was to compare the response of the simulated tractor to that of the experimental tractor. By looking at the steady-state gains of the tractor, adjustments were made to the model to more closely match the experimental results. These adjustments included suspension and steering compliances, as well as auxiliary roll moment modifications. Once the validation of the truck tractor was completed for the current configuration, the existing 53-foot box trailer model was added to the vehicle model. The next stage in experimental validation for the current tractor-trailer model was to incorporate suspension compliances and modify the auxiliary roll stiffness to more closely model the experimental response of the vehicle. The final validation stage was to implement some minor modifications to the existing RSC model.

This study involves two areas of research. The first is the finalization of the Pedestrian Crash Data Study (PCDS) in order to provide detailed information regarding the vehicle/pedestrian accident environment and how it has changed from the interim PCDS information. The pedestrian kinematics, injury contact sources, and injuries were analyzed relative to vehicle geometry. The second area presented is full-scale attempts at reconstruction of two selected PCDS cases using the Polar II pedestrian dummy to determine if the pre-crash motion of the pedestrian and vehicle could somehow be linked to the injuries and vehicle damage documented in the case.

Pedestrian research and testing at the NHTSA Vehicle Research and Test Center has recently focused on assessment of proposed ISO and EEVC head impact test procedures, and extension of these procedures to additional vehicle frontal surfaces. In addition to test parameter sensitivity evaluation, reconstruction of PCDS (Pedestrian Crash Data Study) cases with laboratory impact tests and computer simulations has been conducted. This paper presents the results of this research.

ORVR (Onboard Refueling Vapor Recovery) canisters trap vapors during normal operations of a vehicle's engine, and during refueling. This study evaluates the relative risks involved should a canister rupture in a crash. A canister impactor was developed to simulate real-world impacts and to evaluate the canisters' rupture characteristics. Numerous performance aspects of canisters were evaluated: the energy required to rupture a canister; the spread of carbon particles following rupture; the ease of ignition of vapor-laden particles; the vapor concentration in the area of ruptured, vapor-laden canisters; and the potential of crashes to rupture and ignite canisters. Results from these five items were combined into a risk analysis.

There have been a number of papers written about the dynamic effects of low speed front to rear impacts between motor vehicles during the last several years. This has been an important issue in the field of accident analysis and reconstruction because of the frequency with which the accidents occur and the costs of injuries allegedly associated with them. Several of these papers have discussed the importance of the coefficient of restitution in the accelerations and speed changes that the vehicles undergo in such impacts. These discussions often include data showing the measured restitution for impacts involving various bumper types and closing speeds. However, in most of these studies, the impacts are controlled so that direct bumper to bumper impacts occur. This paper will present the results of several rear impact tests with non-standard impact configurations.

The advent of the Hybrid III crash test dummy marked the beginning of biofidelic anthropomorphic test devices. During the development of its critical components, notably the head, neck, knee, and thorax, biomechanical cadaver test results were incorporated into the design. The result was a dummy that represented the 50th percentile male during idealized impacts. In order to achieve a more biofidelic response from the components, many exotic materials and unique designs were utilized. The thorax, for instance, incorporates a spring steel rib design laminated with a viscoelastic polymeric composite material to damp the response. This combination results in the proper hysteretic losses necessary to model the human thorax under impact loading conditions. The disadvantage of this design is that the damping material properties are highly sensitive to temperature. A variation of more than 5 degrees Fahrenheit dramatically affects the response of the thorax.

The handling, stability, and rollover resistance of vehicles is presently being studied by both the automotive industry and the National Highway and Traffic Safety Administration (NHTSA). However, to study the handling and rollover behavior of each vehicle on the road is not feasible. The ability to categorize and compare the rollover and handling behavior of various vehicles is a subject of considerable research interest. This paper examines the possibility of characterizing vehicle classes through the use of a three degree-of-freedom linear model. Initially, segregation is studied by evaluating the eigenvalue location in the complex domain for vehicle sideslip velocity, yaw rate, and roll angle. Then the influence of numerator dynamics on vehicle behavior is studied and vehicle class segregation is attempted through evaluation of the amplitude ratio of the frequency responses for sideslip velocity, yaw rate, and roll angle.

In the last twelve years, the overwhelming effectiveness of restraining children in the United States, Canada and Europe has been proven in reducing death and injury in automobile accidents. Despite the proven benefits of restraining children, one type of injury has not been prevented. This paper is an analysis of stretch injuries to the spinal cord in the upper thoracic or cervical spine. This paper discusses, in general, spinal cord injuries from a biomechanical point of view. The relationship between various loading conditions and the resulting types of spinal cord injuries is discussed. This paper also examines seven real world automobile accidents. Information for each case includes: vehicles involved, type of roadway, crash Delta-V, occupant direction of motion, restraint type, injuries to occupants, and anthropometry of child with spinal cord injury. A description and location of each spinal cord injury that occurred at the time of the accident is discussed.

A technique has been developed to study the effects of the vehicle interior on the performance of child safety seats. Child safety seat sled tests are used to define the kinematics of the seat and child in a crash situation. Computer animation of this motion is superimposed on the motion of the actual vehicle crash tests giving an estimation of the kinematics of the child and child seat in a real crash situation. The significance of the vehicle interior and the interference of the vehicle interior with the child's kinematics is presented within the computer animation. The analysis is conducted using a single child restraint device in multiple seating conditions within a single vehicle.

This paper summarizes the rationale used to specify the geometric, inertial and impact response requirements for a small adult female dummy and a large adult male dummy with impact biofidelity and measurement capacity comparable to the Hybrid III dummy, the most advanced midsize adult male dummy. Body segment lengths and weights for these two dummies were based on the latest anthropometry studies for the extremes of the U.S.A. adult population. Other characteristic body segment dimensions were calculated from geometric and mass scaling relationships that assured that each body segment had the same mass density as the corresponding body segment of the Hybrid III dummy. The biomechanical impact response requirements for the head, neck, chest and knee of the Hybrid III dummy were scaled to give corresponding biomechanical impact response requirements for each dummy.

The objective of this paper is to investigate the effect of padding on the human thorax. Different types of padding are used in the computer simulations. Lumped models are developed to perform the simulations. Through the responses of the simulations one can determine what kind of padding is desired. This paper provides the first phase of using a computer-aided tool. Though much attention has been paid to either the investigation of padding or human thorax modelling, how the physical properties of padding affect thoracic protection is not well known. The combination of padding and the thorax needs a lot of effort to unveil their relationship. This paper attempts to provide the guideline of what a good padding material should be. The determination of an optimal padding is one of the goals in this study. Hopefully, the results of this paper can make a contribution to the vehicle safety design, especially the car door.

This paper presents an overview of the evolution of computer simulations in vehicle collision and occupant kinematic reconstructions. The basic principles behind these simulations, the origin of these programs and the evolution of these programs from a basic analytical mathematical model to a sophisticated computer program are discussed. In addition, a brief computer development history is discussed to demonstrate how the evolution of computer assisted vehicle accident reconstruction becomes feasible for a reconstructionist. Possible future research in computer reconstruction is also discussed.

This paper presents a review on pedestrian impact reconstruction methodology and offers a comprehensive review of the literature. Several types of analyses are discussed which can be used to reconstruct the accident scenario using the facts collected from the scene. Inclusive in this review is the utilization of skid mark analysis, debris analysis, injury/damage match-up, trajectory analysis, nighttime visibility, and alcohol effects. The pedestrian impact reconstruction methodology is illustrated with a real world case example to point out different observations which can provide insight into the pedestrian/vehicle collision reconstruction approach. The literature review provides a broad foundation of information on pedestrian impact reconstruction and can be used to supplement the techniques presented in this paper in areas related to pedestrian impact. Research advances in the area of pedestrian impact reconstruction are also discussed in this paper.