Search Results

The objective of this study is to investigate the initial flame propagation characteristics of turbulent flame in an engine cylinder through time-series analysis of radical emissions. A spark plug with optical fiber was developed in this study. The plug sensor is M12 type that makes it possible to mount in practical engine. The spark plug sensor can detect radical emissions in time-resolved spectra through time-series spectroscopic measurement. In this spectra, some kinds of radical emissions such as OH*(306nm), CH*(431nm) and C2*(517nm) based on principle of chemiluminescence are observed. In this study, the spark plug sensor was applied to both compression-expansion machine (CEM) and practical engine. As a result of CEM with bottom viewed high-speed camera, three kinds of spectra could be detected.

Bio-gas as an internal combustion (I.C.) engine fuel has many advantages such as cheaper fuel cost, low emission levels and especially the neutral recirculation loop of carbon dioxide, which is one of the principal factors in global warming. In this study, positive potentialities of bio-gas were investigated using a micro co-generation engine. The mixing ratio of methane (CH4) and carbon dioxide (CO2) was changed to simulate various types of bio-gases. Intake air and fuel flow rates were controlled to change the equivalence ratio. The engine load condition could be changed with the electric output power used. Base on the result, the higher CO2 content rate slowed down the engine speed in the same load condition and the combustion speed generally decreased under the same load condition with maintaining the engine speed. However thermal efficiency increased with lean burn conditions and NOX emission decreased with higher CO2 mixing rates.

Hydrogen spark-ignition (SI) engines based on direct-injection (DI) promise significant advantages in terms of thermal efficiency and power output, as well as a means of overcoming problems related to knocking, backfiring, and pre-ignition. In a DI hydrogen engine, the fuel/air mixture is formed by injecting a jet of hydrogen into the air inside the combustion chamber. An Ar-ion laser beam was used as a light source to visualize the hydrogen jet in a constant-volume chamber. This allowed us to study the structure of the jet in addition to other physical processes resulting from hydrogen gas injection. Combustion experiments were conducted in a single-cylinder SI optical research engine equipped with a DI system to detect the early kernel growth assisted by the spark, as well as flame propagation. Various equivalence ratios and fuel injection timings were analyzed to identify the effects on combustion.

The objective of this study is to investigate the performance and emissions in a pilot-ignited supercharged dual-fuel engine, fueled with different types of gaseous fuels under various equivalence ratios. It is found that if certain operating conditions are maintained, conventional dual-fuel engine combustion mode can be transformed to the combustion mode with the two-stage heat release. This mode of combustion was called the PREMIER (PREmixed Mixture Ignition in the End-gas Region) combustion. During PREMIER combustion, initially, the combustion progresses as the premixed flame propagation and then, due to the mixture autoignition in the end-gas region, ahead of the propagating flame front, the transition occurs with the rapid increase in the heat release rate.

Effects of injection parameters on combustion and emission characteristics of diesel PCCI engine operating on optical and test engine was investigated. PCCI combustion was achieved through slightly narrow included angle injector, low compression ratio coupled with exhaust gas recirculation. Analysis based on diesel spray evolution, combustion process visualization and analysis was carried out. Spray penetration was evaluated and related to the exhaust emissions. Advancing the injection timing and EGR extended the ignition delay, decreased NOx emissions and increased HC, smoke and CO emissions. Higher injection pressure led to low emissions of NOx, smoke, HC and comparable CO. Optimum spray targeting position for minimum emission was identified. Impingement on the piston surface led to deterioration of emissions and increased fuel consumption while spray targeting the upper edge of Derby hat wall showed improvement in emission and engine performance.

It is well known that the wavelet transform is a useful time-frequency analysis method for an unsteady signal and major attention has been focused on the selection of the mother wavelet (MW) because the MW plays an important role in the wavelet transform. In this study, we analyze the pressure signal in a spark-ignition engine and the vibration of the engine block measured by a knock sensor under the knocking conditions when knocking is caused. We then propose a new method of the knocking detection that utilizes the knocking signal measured with a knock sensor as a MW. We call this method the Instantaneous Correlation Method (ICM). The degree of similarity between the MW and the vibration of the engine block was judged and only the knocking signal from the vibration of the engine block was extracted. The results obtained here show that the method proposed in this study is useful for knocking detection even if the engine speed is very high of 6000rpm.

Hydrogen is expected to be one of the most prominent fuels in the near future for solving greenhouse problem, protecting environment and saving petroleum. In this study, a dual fuel engine of hydrogen and diesel oil was investigated. Hydrogen was inducted in a intake port with air and diesel oil was injected into the cylinder. The injection timing was changed over extremely wide range. When the injection timing of diesel fuel into the cylinder is advanced, the diesel oil is well mixed with hydrogen-air mixture and the initial combustion becomes mild. NOx emissions decrease because of lean premixed combustion without the region of high temperature of burned gas. When hydrogen is mixed with inlet air, emissions of HC, CO and CO2 decrease without exhausting smoke while brake thermal efficiency is slightly smaller than that in ordinary diesel combustion.

It is necessary to understand the entrainment process of ambient air into diesel sprays for the combustion process. This study focused on the entrainment process of non-combusting and combusting hydrogen jets instead of evaporated fuel sprays because of ease with measurement for fundamental research. Spatial and temporal changes of the air entrainment into the jets were obtained using flow visualization technique. The experimental results showed that the total air mass entrained into the flame jet is nearly equal to that into the cold jet. The rate of entrainment per unit area of the flame jet is smaller than that in the cold jet. When a transient jet is separated into side and front parts, the rate of air mass entrained from the front part of the jet decreases with time while the rate into the side of the jet per unit area is almost the same. The total air mass entrained into the jet can be approximately explained by the momentum theory.

A turbulent gas jet impinging on a flat wall was visualized by a laser sheet method. Velocity fields were determined from the images with a high speed video system by processing them in terms of the cross correlation method for the jet and particle tracking method for the ambient air from the same images. The vortex flow near the transient jet tip impinging on the wall was visualized and analyzed successfully. The velocity field obtained from the above methods was compared to that determined with a laser Doppler anemometer. The path line of a certain period which was taken with a CCD camera with controlled shutter was analyzed and the mean rate of air entrainment was determined quantitatively. The spatial and temporal change of the entrainment rate was estimated and it was found that the entrainment rate near the upstream part of the jet tip region is larger because of the vortex.

A path line method utilizing a CCD random shutter camera and a laser light sheet was applied for obtaining the air mass entrained into a transient gas jet. Large, light weight particles and fine particles were used for scattering the path lines of the surroundings and visualizing the approximate shape of the jet, respectively The jet configuration and the entrainment process could be visualized simultaneously, and this path line method was found to be very useful for estimating the air mass entrained because of the good agreement with the value obtained using LDA data. The spatial and temporal change of the ambient air entrainment into the jet was approximately clarified.