Search Results

Bioethanol is being used as an alternative fuel throughout the world based on considerations of reduction of CO2 emissions and sustainability. It is widely known that ethanol has an advantage of high anti-knock quality. In order to use the ethanol in ethanol-blended gasoline to control knocking, the research discussed in this paper sought to develop a fuel separation system that would separate ethanol-blended gasoline into a high-octane-number fuel (high-ethanol-concentration fuel) and a low-octane-number fuel (low-ethanol-concentration fuel) in the vehicle. The research developed a small fuel separation system, and employed a layout in which the system was fitted in the fuel tank based on considerations of reducing the effect on cabin space and maintaining safety in the event of a collision. The total volume of the components fitted in the fuel tank is 6.6 liters.

Gasoline engines have the trace-knock phenomena induced by the fast combustion which happens a few times during 100 cycles. And that constrains the thermal efficiency improvement due to limiting the ignition timing advance. So the authors have been dedicating a trace-knock simulation so that we could obtain any pieces of information associated with trace-knock characteristics. This simulation consists of a turbulent combustion model, a cycle-by-cycle variation model and a chemical calculation subprogram. In the combustion model, a combustion zone is considered in order to obtain proper turbulent combustion speed through wide range of engine speed. From a cycle-by-cycle variation analysis of an actual gasoline engine, some trace-knock features were detected, and they were involved in the cycle-by-cycle variation model. And a reduced elementary reaction model of gasoline PRF (primary reference fuel) was customized to the knocking prediction, and it was used in the chemical calculation.

It is experimentally known that the surface color of bearing balls gradually becomes brown during long term operation of the bearings under appropriate lubrication conditions. That exhibits the possibility of an estimation method for residual life of ball bearings without any abnormal wear on the surfaces by precise color measurements. Therefore, we examined what set colors on bearing balls by surface observation using scanning electron microscopy and subsurface analysis using transmission electron microscopy. Results showed that an amorphous carbon layer had gradually covered ball surfaces during operation of the bearings. The layer not only changed ball color but also made overall ball shapes closer to a complete sphere. The report also introduces a uniquely developed color analyzer which enabled color measurements on metallic surfaces, such as the above-mentioned balls.

The purpose of this research was to predict the amount of wear on exhaust valve seats in durability testing of gasoline engines. Through the rig wear test, a prediction formula was constructed with multiple factors as variables. In the rig test, the wear rate was measured in some cases where a number of factors of valve seat wear were within a certain range. Through these tests, sensitivity for each factor was determined from the measured wear data, and then a prediction formula for calculating the amount of wear was constructed with high sensitivity factors. Combining the wear amount calculation formula with the operation mode of the actual engine, the wear amount in that mode can be calculated. The calculated wear amount showed a high correlation with the wear amount measured in bench tests and the wear amount measured in vehicle tests.

Increasing the strength of materials is effective in reducing weight and boosting structural part performance, but there are cases in where the residual strain generated during the process of manufacturing of high-strength materials results in a decline of durability. It is therefore important to understand how the residual strain in a manufactured component changes due to processing conditions. In the case of a connecting rod, because the strain load on the connecting rod rib sections is high, it is necessary to clearly understand the distribution of strain in the ribs. However, because residual strain is generally measured by using X-ray diffractometers or strain gauges, measurements are limited to the surface layer of the parts. Neutron beams, however, have a higher penetration depth than X-rays, allowing for strain measurement in the bulk material.

In recent years, studies have been conducted on the relationship between the J factor, which indicates flow of molten aluminum at the time of injection, and the quality of HPDC products. The flow of molten metal at a high J factor is referred to as “Atomized Flow.” The authors and others conducted studies on the relationship between the J factor and the strength of HPDC products. An area exceeding 300MPa was found in the product produced at a high J factor corresponding to the “Atomized Flow.” The defect was less in the above-mentioned position because the gas porosity was finely dispersed. Considering that the fine dispersion of gas porosity is related to the “Atomized Flow”, pictures were taken to analyze “Atomized Flow.” The molten aluminum was ejected into an open space at a high speed and the splashed conditions were photographed. From the images taken by the pulse laser permeation, the conditions of microscopic atomized flow were observed precisely.

We developed a copper catalyst using zero Platinum group metals (hereafter PGMs) to fit motorcycle specific emission gas environment. Though many research reports to develop catalyst without using PGMs that are precious and costly resources are available, no reports had proven Base Metal Catalyst development to meet actual emission regulation equivalent to PGM catalysts. Compared to conventional PGM catalysts, higher temperature is required to keep high catalytic conversion efficiency by utilizing properties of this Base Metal Catalyst. Thus, this Base Metal Catalyst is located in cross coupling position, though it is rare case in motorcycle. This catalyst location could cause negative impacts on engine knocking, engine performance and drivability. This time, to overcome such negative impacts we optimized whole exhaust system, including parts around catalyst.

For the purpose of developing onboard gasoline reforming technology for higher octane number fuel on demand, octane number enhancement of gasoline surrogate by aerobic oxidation using N-hydroxyphthalimide catalyst was investigated. At first, octane numbers of the oxygen-containing products from alkane and aromatic compound were estimated using a fuel ignition analyzer. As a result, not only alcohol but also ketones and aldehydes have higher octane numbers than the original alkanes and aromatic compound. Next, gasoline surrogate was oxidized aerobically with N-hydroxyphthalimide derivative catalyst and cobalt catalyst at conditions below 100 °C. As a result, fuel molecules were oxidized to produce alcohols, ketones, aldehydes, and carboxylic acids. N-hydroxyphthalimide derivative catalyst with higher solubility in gasoline surrogate has higher oxidation ability. Furthermore, the estimated octane number of the oxidized gasoline surrogate improves 17 RON.

A 1.5 L downsizing turbocharged engine was developed to achieve both driving and environmental performance. The engine is intended to replace 1.8 - 2.4 L class NA engines. In downsizing turbocharged engines, mixture homogeneity is important for suppressing knocking and emission reduction. Particularly under high load, creating rapid combustion and a homogeneous mixture are key technologies. The authors used a long-stroke direct injection engine, which has outstanding rapid combustion and thermal efficiency, as a base engine meeting these requirements. They combined this with a high-tumble port and shallow-dish piston intended to support tumble flow. The combination enhanced flow within the cylinder. The combustion system was built to include a sodium-filled exhaust valve to reduce knocking and a multi-hole injector (six holes) for mixture homogeneity and to reduce the fuel wall wetting.

This paper introduces the newly developed super sports car engine mounted in the new model NSX. A super sports car engine was newly developed to satisfy the high power performance required by the body package. Higher power and compactness were simultaneously achieved by selecting an engine displacement of 3.5 L and by using a V6 layout and a turbocharger. This enabled to mount a power train that combines a hybrid motor with a newly developed transmission in the rear of the body. The lubrication system uses a dry sump system capable of maintaining reliable lubrication in all possible super sports car driving scenarios. The combustion system uses high tumble-flow ports, a direct injection and a port injection system that increase power performance and thermal efficiency, emission reduction. To support the increased heat load due to higher power, a 3-piece water jacket is used around the combustion chamber and the exhaust ports.

We had developed Electric Servo Brake System, which can control brake pressure accurately with a DC motor according to brake pedal force. Therefore, the system attains quality brake feeling while reflecting intentions of a driver. By the way, “Build-up” is characteristics that brake effectiveness increases in accordance with the deceleration of the vehicle, which is recognized as brake feeling with a sense of relief as not to elongate an expected braking distance at a downhill road due to large-capacity brake pad such as sports car and large vehicles. Then, we have applied the optical characteristic control to every car with Electric Servo Brake System by means of brake pressure control but not brake pad. Hereby, we confirmed that the control gives a driver the sense of relief and the reduction of pedal load on the further stepping-on of the pedal. In this paper, we describe the development of brake feel based on the control overview.

Nowadays, highly super charging is required corresponded to downsizing concept for improving thermal efficiency in direct-injected spark ignition (DISI) engine. However, highly super charging increases the possibility of super-knock caused by pre-ignition. Recently, in many studies, the reason of pre-ignition has been investigated but the reason why pre-ignition leads such strong knocking called super-knock has not been investigated. In DISI engine, it is estimated that there is more inhomogeneity of equivalence ratio and temperature of air-fuel mixture than it in port injection SI engine. In this study, factors which decide self-ignition timing was reviewed and the influence of inhomogeneity of air-fuel mixture to super-knock was investigated based on numerical calculation.

Bio-ethanol is used worldwide in fuel mixtures such as E10 gasoline. In this study, an onboard fuel system employing a pervaporation membrane was investigated to separate E10 into high-octane-number fuel (high-concentration ethanol fuel) and low-octane-number fuel (low-concentration ethanol fuel). The optimal operation conditions and size of the membrane unit for the separation system were determined in consideration of the separation rate and vehicle installation. This system can supply separated ethanol with sufficient speed and quantity to improve engine performance under practical driving conditions. In addition, the study was conducted to confirm that separated fuels have properties sufficient for use in automobiles. This separation rate enabled 5-cycle-mode driving without temporary shortage of permeated fuel.

One of the authors has proposed to use the decay rate of EHRR, the effective heat release rate, d2Q/dθ2 as an index for the rapid local combustion [1]. In this study, EHRR profiles and the cylinder gas pressure oscillations of the low and high speed knock are analyzed by using this index. A delayed rapid local combustion, such as an autoignition with small burned mass fraction can be detected. In the cases of the low speed knock, it has been agreed that a rapid local combustion is an autoignition. Although whether the cylinder gas oscillation is provoked by an auto ignition in a certain cycle or not is an irregular phenomenon, the auto ignition takes place in almost all of the cycles in the knocking condition. Mixture mass fraction burned by an auto ignition is large. A small auto ignition may induce a secondary auto ignition, in many cases, mass burned by the secondary auto ignition is extremely large.

In order to reduce automobile body weight and improve crashworthiness, the use of high-strength steels has increased greatly in recent years. An optimal combination of both crash safety performance and lightweight structure has been a major challenge in automobile body engineering. In this study, the Cockcroft-Latham fracture criterion was applied to predict the fracture of high-strength steels. Marciniak-type biaxial stretching tests for high-strength steels were performed to measure the material constant of the Cockcroft-Latham fracture criterion. Furthermore, in order to improve the simulation accuracy, local anisotropic parameters based on the plastic strain (strain dependent model of anisotropy) were measured using the digital image grid method and were incorporated into Hill's anisotropic yield condition by the authors. In order to confirm the validity of the Cockcroft-Latham fracture criterion, uniaxial tensile tests were performed.

Downsizing or higher compression ratio of SI engines is an appropriate way to achieve considerable improvements of part load fuel efficiency. As the compression ratio directly impacts the engine cycle thermal efficiency, it is important to increase the compression ratio in order to reduce the specific fuel consumption. However, when operating a highly boosted / downsized SI engine at full load, the actual combustion process deviates strongly from the ideal Otto cycle due to the increased effective loads requiring ignition timing delay to suppress abnormal combustion phenomena such as engine knocking. This means that for an optimal design of an SI engine between balances must be found between part load and full load operation. If the knocking characteristic can be accurately predicted beforehand when designing the combustion chamber, a reduction of design time and /or an increase in development efficiency would be possible.

Attempts were made to measure knocking phenomenon by an optical method, which is free from influences of mechanical noises and is allowing an easy installation to an engine. Using a newly developed high durability optical probe, the light intensity of hydroxyl radical component, which is diffracted from the emitted light from combustion, was measured. The intensity of this emission component was measured at each crank angle and the maximum intensity in a cycle was identified. After that, the angular range in which the measured intensity exceeded 85% of this maximum intensity was defined as “CA85”. When a knocking was purposely induced by changing the conditions of the engine operation, there appeared the engine cycles that included CA85 less than a crank angle of 4 degrees. The frequency of occurrence of CA85 equal to or less than 4 degrees within a predetermined number of engine cycles, which can be interpreted as a knocking occurrence ratio, was denoted as “CA85-4”.

This research is aimed at development of the catalyst for gasoline automobiles which uses only palladium (Pd) among platinum group metals (PGMs). And the conformity emission category aimed at LEV III-SULEV30. For evaluation, the improvement effect was verified for 2013 model year (MY) ACCORD (LEV II-SULEV) as the reference. As compared with Pd-rhodium (Rh) catalyst, a Pd-only catalyst had the low purification performance of nitrogen oxides (NOx), and there was a problem in the drop in dispersion of Pd by sintering, and phosphorus (P) poisoning.

Bio-ethanol is used in many areas of the world as ethanol blended gasoline at low concentrations such as “E10 gasoline”. In this study, a method was examined to effectively use this small amount of ethanol within ethanol blended gasoline to improve thermal efficiency and high-load performance in a high-compression-ratio engine. Ethanol blended gasoline was separated into high-concentration ethanol fuel and gasoline using a fuel separation system employing a membrane. High-ethanol-concentration fuel was selectively used at high-load conditions to suppress knocking. In this system, a method to decrease ethanol consumption is necessary to cover the wide range of engine operation. Lower ethanol consumption could be achieved by Miller-cycle operation because decrease of the effective compression ratio suppresses knocking. However, high-load operation was limited due to the decrease in intake air volume with Miller-cycle operation.

A fuel design concept for an HCCI engine based on chemical kinetics to optimize the heat release profile and achieve robust ignition was proposed, and applied to the design of the optimal methane-based blend. Ignition process chemistry of each single-component of natural gas, methane, ethane, propane, n-butane and isobutane, was analyzed using detailed chemical kinetic computations. Ethane exhibits low ignitability, close to that of methane, when the initial temperature is below 800 K, but higher ignitability, close to those of propane, n-butane and isobutane, when the initial temperature is above 1100 K. Furthermore, ethane shows a higher heat release rate during the late stage of the ignition process. If the early stage of an ignition process takes place during the compression stroke, this kind of heat release profile is desirable in an HCCI engine to reduce cycle-to-cycle variation during the expansion stroke.