Search Results

Octane-on-Demand (OoD) is a promising technology for reducing greenhouse emissions from automobiles. The concept utilizes a low-octane fuel for low and mid load operating conditions, and a high-octane additive is added at high load operating conditions. Researchers have focused on the minimum ethanol content required for operating at high load conditions when the low-octane fuel becomes knock limited. However, it is also widely known that ethanol has a high tendency to pre-ignite, which has been linked with its high laminar flame speed and surface ignition tendency. Moreover, ethanol has a lower stoichiometric air-fuel ratio, requiring a larger injected fuel mass per cycle. A larger fuel mass increases the potential for oil dilution by the liquid fuel, creating precursors for pre-ignition. Hence, the limits on ethanol addition owing to pre-ignition also need consideration before the technology can be implemented.

The blending behavior of ethanol in five different hydrocarbon base fuels with octane numbers of approximately 70 and 84 was examined under Spark-Ignited (SI) and Homogeneous Charge Compression Ignited (HCCI) operating conditions. The Blending octane number (BON) was used to characterize the blending behavior on both a volume and molar basis. Previous studies have shown that the blending behavior of ethanol generally follows several well-established rules. In particular, non-linear blending effects are generally observed on a volume basis (i.e. BON > RON or MON of pure ethanol; 108 and 89, respectively), while linear blending effects are generally observed on a molar basis (i.e. BON = RON or MON of pure ethanol). This work firstly demonstrates that the non-linear volumetric blending effects traditionally observed under SI operating conditions are also observed under HCCI operating conditions.

Gasoline-ethanol-methanol (GEM) blends, with constant stoichiometric air-to-fuel ratio (iso-stoichiometric blending rule) and equivalent to binary gasoline-ethanol blends (E2, E5, E10 and E15 in % vol.), were defined to investigate the effect of methanol and combined mixtures of ethanol and methanol when blended with three FACE (Fuels for Advanced Combustion Engines) Gasolines, I, J and A corresponding to RON 70.2, 73.8 and 83.9, respectively, and their corresponding Primary Reference Fuels (PRFs). A Cooperative Fuel Research (CFR) engine was used under Spark Ignition and Homogeneous Charge Compression Ignited modes. An ignition quality tester was utilized in the Compression Ignition mode. One of the promising properties of GEM blends, which are derived using the iso-stoichiometric blending rule, is that they maintain a constant octane number, which has led to the introduction of methanol as a drop-in fuel to supplement bio-derived ethanol.

The effect of ethanol blended with three FACE (Fuels for Advanced Combustion Engines) gasolines, I, J and A corresponding to RON 70.3, 71.8 and 83.5, respectively, were compared to PRF70 and PRF84 with the same ethanol concentrations, these being 2%, 5%, 10%, 15% and 20% by volume. A Cooperative Fuel Research (CFR) engine was used to understand the blending effect of ethanol with FACE gasolines and PRFs in spark-ignited and homogeneous charge compression ignited mode. Blending octane numbers (BON) were obtained for both the modes. All the fuels were also tested in an ignition quality tester to obtain Blending Derived Cetane numbers (BDCN). It is shown that fuel composition and octane number are important characteristics of all the base fuels that have a significant impact on octane increase with ethanol. The dependency of octane number for the base fuel on the blending octane number depended on the combustion mode operated.

This paper is the second of a two part study which investigates the use of advanced combustion modes as a means of improving the efficiency and environmental impact of conventional light-duty vehicles. This second study focuses on drive cycle simulations and Life Cycle Assessment (LCA) for vehicles equipped with Octane-on-Demand combustion. Methanol is utilized as the high octane fuel, while three alternative petroleum-derived fuels with Research octane numbers (RONs) ranging from 61 to 90 are examined as candidates for the lower octane fuel. The experimental engine calibration maps developed in the previous study are first provided as inputs to a drive cycle simulation tool. This is used to quantify the total fuel consumption, octane requirement and tank-to-wheel CO2 emissions for a light-duty vehicle equipped with two alternative powertrain configurations. The properties of the lower octane fuel are shown to affect the vehicle fuel consumption and CO2 emissions significantly.

This paper is the first of a two part study which investigates the use of advanced combustion modes as a means of improving the efficiency and environmental impact of conventional light-duty vehicles. This first study focuses on the application of so-called Octane-on-Demand combustion, whereby the fuel anti-knock quality is customized to match the real-time requirements of an otherwise conventional spark-ignition engine. Methanol is utilized as the high octane fuel, while three alternative petroleum-derived fuels with Research octane numbers (RONs) ranging from 61 to 90 are examined as candidates for the lower octane fuel. Experimental engine calibration maps are first developed to quantify the minimum amount of methanol that must be added to each lower octane fuel in order to reproduce the baseline engine performance attained on a market gasoline (RON 95). The properties of the lower octane fuel are shown to affect the engine performance significantly.