Search Results

Recent growth in automotive applications of magnesium die cast alloys has made the refining and recycling of magnesium scrap a key issue for the automotive and magnesium industries, if growth is to continue. Today, with only a few exceptions, commercially refined and recycled alloy is produced using a variety of flux-based processes. However, fluxless refining, has been the focus of growing interest, particularly for the in-house refining of scrap by the die cast producers. This paper summarizes the results of a study conducted to better understand the behavior of non-metallic contaminants in scrap melts and the requirements for their separation, using argon sparging. Brightness measurements were used to experimentally determine the distribution of non-metallic contaminants within scrap melts both before and after argon treatment.

The persistent occurrence of microporosity defects in AZ91 castings has made it difficult to consistently produce sound parts. Earlier work established that dissolved hydrogen gas causes microporosity defects in AZ91; however, the exact role of hydrogen in the nucleation and growth of microporosity was not determined. In this paper, the behavoir of dissolved hydrogen gas in elemental magnesium, AZ91 alloy, and liquid binary Mg/Al alloys was studied. The results show that during the last stages of solidification, hydrogen gas is rejected from the Mg17Al12 intermetallic compound to assist in the nucleation and/or growth of microporosity.

The relationship between hydrogen gas and microporosity in magnesium alloy AZ91 was quantified, refuting the belief that hydrogen levels less than the maximum solid solubility are of no detriment. Sand castings were made from melts containing measured levels of hydrogen gas, and the amount of porosity was determined by density measurements. At concentrations below the maximum solid solubility, it was established that the amount of microporosity is directly proportional to the gas content. This supports the premise that dissolved hydrogen gas provides nucleation sites for microporosity, and that it is useful to remove all gas to achieve porosity-free cast parts.

Adhesive materials are required to bond cover fabrics to most molded interior headliner substrates. Several thermoplastic adhesive films are qualified and used at U.S. and Japanese OEM's. These adhesive films offer benefits such as convenience, cost effectiveness, excellent adhesive performance and process efficiency while reducing concerns of emissions and hazardous waste handling compared to prior bonding methods. The automotive headliner part is a multifunctional component of the vehicle's interior trim. One of the main headliner functions is to reduce the interior cabin noise. Various adhesive materials are used in a lamination process to form a composite headliner. The purpose of this study was to compare the effects of this lamination process and various alternative adhesive materials on the overall acoustical performance of the headliner composite. Various headliner samples were fabricated under controlled process conditions and tested by an independent acoustics testing lab.

A method for refining magnesium scrap which produces consistent, high quality magnesium metal has been developed. High quality magnesium metal is defined in this paper as metal which has heavy metal contaminants controlled within high-purity ASTM chemical specification, and is relatively free of internal impurities such as non-metallic inclusions (oxides and flux) and dissolved gas. The refining process utilizes a protective gas atmosphere, inert gas sparging and filtration techniques, rather than salt based fluxes, to remove both non-metallic inclusions and dissolved gases. Experimentation results of this refining process indicate magnesium scrap can be remelted and refined to a quality equal to or better than virgin ingot, without the introduction of salt based fluxes or a large capital investment.

The construction of most automotive interior headliners requires an adhesive material to bond polyurethane foam-backed fabric to a molded headliner shell. More than ten years ago, The Dow Chemical Company qualified and began supplying a thermoplastic adhesive polymer film for headliner applications which replaced wet adhesive systems at several fabricators. DAF 899 adhesive film has gained acceptance in the industry due to excellent performance, convenience, and cost effectiveness without additional waste handling or volatile organic emission concerns. Recent advancements in headliner design such as additional recessed areas with more demanding contours, new substrate materials and the desire for more efficient operations created an opportunity to design improved adhesive films to meet the emerging industry demands.

Gas generators for filling auto air cushions have been developed in several compact sizes and configurations. All-solid chemical-generating compositions have been developed to give nearly pure nitrogen gas. Other compositions developed give mainly carbon dioxide. Gas cushions ranging in size from 1-12 ft3 have been inflated. Deployment time, bag temperature, and sound level are within safe limits. Toxicity tests have been performed on dogs without harmful effects being observed.