Search Results

Ongoing efforts in applying a “high-end” turbulent combustion model (a transported probability density function - tPDF - method) to direct-injection internal combustion engines are discussed. New numerical algorithm and physical modeling issues arise compared to more conventional modeling approaches. These include coupling between Eulerian finite-volume methods and Lagrangian Monte Carlo particle methods, liquid fuel spray/tPDF coupling, and heat transfer. Sensitivity studies are performed and quantitative comparisons are made between model results and experimental measurements in a diesel/PCCI engine. Marked differences are found between tPDF results that account explicitly for turbulence/chemistry interactions (TCI) and results obtained using models that do not account for TCI. Computed pressure and heat release profiles agree well with experimental measurements and respond correctly to variations in engine operating conditions.

Biodiesel fuels are widely known to yield an increase in NOx emissions in many diesel engines. It has been suggested that the increase in NOx is due to injection timing differences caused by the low compressibility of biodiesel. In this work, comparisons of injection timing and duration were performed for diesel fuel and a range of biodiesel blends (B20 to B100). The fuel injector on a 4-stroke, single-cylinder, four horsepower, air-cooled, direct injection diesel engine was positioned in a spray chamber while the engine was motored and fuel was delivered to the injector by the fuel pump on the engine. Spray visualization and quantification of injection timing were performed in the spray chamber using an engine videoscope, light attenuation from a HeNe laser and fuel line pressure, and were synchronized to crank shaft position.

Several oxygenates have been proposed and tested for use with diesel fuel as a means of reducing exhaust emissions. This paper examines dimethyl ether (DME), which can be produced in many ways including via Air Products and Chemicals, Inc's Liquid Phase Technology (LPDME ™). Modest additions of DME into diesel fuel (2 wt.% oxygen) showed reductions in particulate matter emissions, but the previous data reported by the author from a multicylinder Navistar 7.3L Turbodiesel engine were scattered. In this study, experiments were performed on a multi-cylinder Navistar 7.3L Turbodiesel engine to repeatably confirm and extend the observations from the earlier studies. This is an important step in not only showing that the fuel does perform well in an engine with minor modifications to the fuel system, but also showing that DME can give consistent, significant results in lowering emissions.

An experimental study was conducted to determine if an organic fuel additive could reduce engine out hydrocarbon and NOx emissions. A production four cylinder spark ignited engine with throttle body fuel injection was used for the study. A full boiling range base fuel, an additized base fuel, a base fuel with methyl tertiary butyl ether (MTBE) and a base fuel with MTBE and additive were used in the engine tests. Additive concentration was 1/2% by mass. Hydrocarbon and NOx measurements were recorded for 11 load/speed conditions. Hydrocarbon speciation data was taken at two of these conditions. The data from the experiments was analyzed in a pair-wise fashion for the fuels with and without the additive to determine whether statistically significant changes occurred.

A study has been experimentally conducted in an optically-accessible DI Diesel engine operating on 50/50 mixture of iso-octane and tetradecane to evaluate a planar laser light scattering technique for the in-cylinder study of soot. Two simultaneous images, taken with vertically and horizontally polarized scattered light, were used to determine the polarization ratio, CHH/CW. This magnitude of the polarization ratio was employed to distinguish soot particles from fuel droplets. The spatial and temporal variations of soot during the combustion cycle were investigated with images taken at various crank angles and swirl levels at three different planes in the combustion bowl. For the high swirl case, soot was uniformly distributed in the combustion bowl. For the non-swirl case, however, soot was mainly observed near the wall and at the top plane, and was observed to exist later into the expansion stroke.

Theoretical and experimental investigations of fuel charge stratification by injection into swirling air are presented. Single drop mechanics are used with some modifications. Theoretical fuel-air ratio plots help explain the mechanism of fuel stratification, and are useful in giving directions for optimizing operating conditions. Engine tests show that the stratification system is practicable for idle and low load conditions, and in combination with homogeneous charge induction for up to full load. Such system would use extremely simple injection equipment without any fuel-air ratio controls, and be rather insensitive to timing between injection and spark.

THE effects of introducing a portion of the fuel charge of a diesel engine into the intake manifold in the form of a fine mist are reported in this paper. Laboratory tests with swirl-chamber and open-chamber engines resulted in smoke reduction up to 80%, increase in smoke-limited power output up to 18.5%, decrease in specific fuel consumption up to 9.8%, shorter ignition lag, lower maximum rate of pressure rise, and smoother operation. In running on good-grade diesel fuel approximately 15% of the main fuel proved to be as good a manifold fuel as any. It was also found that a diesel engine could operate satisfactorily on substandard fuels down to zero cetane number when fumigation was employed. Maximum benefits from fumigation accrued when inducting fuel in the form of a very fine mist (not over 4 microns) produced by Micro-Fog. As yet an economical method of producing this finely atomized fuel spray in large quantities has not been found.