Search Results

The efforts of the ISO “Test Variability Task Force” have been aimed at improving the understanding and at reducing brake dynamometer test variability during performance testing. In addition, dynamometer test results have been compared and correlated to vehicle testing. Even though there is already a vast amount of anecdotal evidence confirming the fact that different procedures generate different friction coefficients on the same brake corner, the availability of supporting data to the industry has been elusive up to this point. To overcome this issue, this paper focuses on assessing friction levels, friction coefficient sensitivity, and repeatability under ECE, GB, ISO, JASO, and SAE laboratory friction evaluation tests.

Relative velocity detection thresholds of drivers are one factor that determines their ability to avoid rear-end crashes. Laboratory, simulator and driving studies show that drivers could scale relative velocity when it exceeded the threshold of about 0.003 rad/sec. Studies using accident reconstruction have suggested that the threshold may be about ten times larger. This paper discusses this divergence and suggests reasons for it and concludes that the lower value should be used as a true measure of the psychological threshold for detection of relative velocity.

Development of reliable magnesium (Mg) to steel joining methods is one of the critical issues in broader applications of Mg in automotive body construction. Ultrasonic spot welding (USW) has been demonstrated successfully to join Mg to steel and to achieve strong joints. In this study, corrosion test of ultrasonic spot welds between 1.6 mm thick Mg AZ31B-H24 and 0.8 mm thick galvanized mild steel, without and with adhesive, was conducted. Adhesive used was a one-component, heat-cured epoxy material, and was applied between overlapped sheets before USW. Corrosion test was conducted with an automotive cyclic corrosion test, which includes cyclic exposures of dipping in the 0.5% sodium chloride (NaCl) bath, a constant humidity environment, and a drying period. Lap shear strength of the joints decreased with the cycles of corrosion exposure. Good joint strengths were retained at the end of 30-cycle test.

The introduction of MultiAir technology [8] has had a strong impact on engine performance, fuel consumption, emissions and control. This technology, intended at first for gasoline engines and applied only on intake valves, is aiming at the reduction of engine breathing losses and, as a consequence, reduction of pollutant emissions and fuel consumption, together with an improvement of maximum intake efficiency. Further positive effects of MultiAir technology have been a significant improvement of Low End Torque, engine driveability (“fun-to-drive” index) and other operating conditions (e.g. idle control). Current development of MultiAir technology is focusing on a better management of hot EGR (Exhaust Gas Recirculation), still acting only on the intake side, although with specifically designed valve lift profiles. This application of MultiAir technology is pushing gasoline engines towards new levels of performance improvements.

Modern project management including brake testing includes the exchange of reliable results from different sources and different locations. The ISO TC22/SWG2-Brake Lining Committee established a task force led by Ford Motor Co. to determine and analyze root causes for variability during dynamometer brake performance testing. The overall goal was to provide guidelines on how to reduce variability and how to improve correlation between dynamometer and vehicle test results. This collaborative accuracy study used the ISO 26867 Friction behavior assessment for automotive brake systems. Future efforts of the ISO task force will address NVH and vehicle-level tests. This paper corresponds to the first two phases of the project regarding performance brake dynamometer testing and presents results, findings and conclusions regarding repeatability (within-lab) and reproducibility (between-labs) from different laboratories and different brake dynamometers.

A hybrid electric vehicle simulation tool (IBZ-Simulator) has been developed at the Fuel Cell Institute of the University of Applied Sciences Esslingen to study the fuel economy potential of a Fuel Cell hybrid urban bus. In this paper, the fundamental architecture of the FC urban buses was described, as well as the control strategy to manage the power flow between the different elements of the drive train. A comparison of the hybrid with the conventional type and ICE-hybrid type is performed, and important factors relating to the vehicle efficiency (accessory loads, vehicle mass, Fuel Cell system ramping rate and battery capacity) were assessed. The using of supercapacitor (or ultracapacitors) as peak power buffer has been investigated.

The Auto/Steel Partnership Corrosion Project Team has completed a perforation corrosion test program consisting of on-vehicle field exposures and various accelerated tests. Steel sheet products with eight combinations of metallic and organic coatings were tested, utilizing a simple crevice coupon design. On-vehicle exposures were conducted in St. John's and Detroit for up to seven years to establish a real-world performance standard. Identical test specimens were exposed to the various accelerated tests, and the results were compared to the real-world standard. This report documents the results of these tests, and compares the accelerated test results (including SAE J2334, GM9540P, Ford APGE, CCT-I, ASTM B117, South Florida Modified Volvo, and Kure Beach (25-meter) exposures) to the on-vehicle tests. The results are compared in terms of five criteria: extent of corrosion, rank order of material performance, degree of correlation, acceleration factor, and control of test environment.

A review of many years of published work has shown that hydrogen embrittlement can occur under rolling contact conditions. Breakdown of lubrication and contamination with water have been cited as the probable sources of atomic hydrogen. In this paper, a unique fracture morphology is identified and the mechanism of the fracture progression from initiation to final catastrophic failure is proposed. Development of beneficial residual compressive stress near the contacting surfaces is one approach used to avoid this type of failure. Several alternative methods capable of developing a more desirable stress distribution will be discussed.

Modern approaches to durability assurance in ground vehicle design are reviewed in the context of recent developments in computer-based analytical and experimental tools for use by designers and development engineers. Examples, using an automotive wheel assembly, are presented to illustrate the application of fatigue analysis in product development. Major challenges associated with the linking of various design tools into integrated networks appropriately configured for industrial problem solving are discussed along with an assessment of the potential benefits to be gained from such integration.

This paper provides a review of the fatigue properties reported in the open literature for die cast magnesium-based alloys. Recently developed fatigue data, in the form of stress versus number of cycles to failure for bending fatigue (R=-1), are presented for die cast AM60B and AZ91D alloy specimens with thicknesses between 1 and 10 mm. The effects of specimen thickness and macrostructural features, such as porosity distributions and surface features (parting line and ejection pin marks), on the fatigue data are discussed.

There is an ongoing interest in biodegradable hydraulic fluids. Biodegradable fluids are often considered to include only vegetable oils, polyol esters and diester base stocks. However, other fluid base stocks including highly refined mineral oils, poly(alpha olefins) and fire-resistant fluids such as water-glycol hydraulic fluids are also biodegradable fluid alternatives. This paper will provide an overview of the international literature on biodegradable fluids, various international testing protocol, fluid base stocks, effect of oxidative stability, material compatibility and pump performance.

The timing of lubricating oil changes for passenger vehicles are based on set time or mileage intervals specified by their manufacturers. A few vehicle manufacturers use more sophisticated methods such as logging the engine speed and temperature and calculating the oil change intervals from this data. Neither technique tells the vehicle user anything about the true state of the oil. A novel form of viscosity sensor based on a vibrating piezoceramic element has been developed. Based on the output from such a device, a more accurate determination of the oil change interval can be made and abnormal conditions (such as the leakage of fuels into the lubricating oil) can be detected. This paper gives a brief description of the device itself and shows results from prototype samples.

The results of analyses on 300 samples of engine oil purchased in the retail market in 1990 are discussed. All samples were labeled with the API SF or SG Service Category, separately, or in combination with an API C category designation. Also, 17 oils previously found to be questionably labeled, from the 1989 set, were repurchased and analyzed. These results are included.

The results of analyses on 300 samples of engine oils that were purchased at retail during 1989 are presented and discussed. All samples were labeled SF or SG, separately or in combination with a C category designation. Additionally, 14 engine oils previously sampled and found to be questionably labeled were resampled and analyzed. These results are discussed.

A brief overview of the history and scope of the SAE Oil Labeling Assessment Program is presented. Then, the results of analyses on 893 samples of engine oil purchased in the retail market over the first three years of the program, are discussed. All samples were labeled with the API SF or SG Service Category, separately, or in combination with an API “C” category designation. Additionally, 43 engine oil samples found to be questionably labeled, were repurchased and analyzed; these results are included.

This paper briefly reviews the scope of the Oil Labeling Assessment Program (OLAP) and the planning involved in conducting the program. The results of analyses on 148 samples of engine oils that were purchased at retail in the fall of 1988 are presented and discussed. All samples were labeled SF or SG, separately or in combination with a C category designation. A comparison of these results with those obtained in previous years is presented. Additionally, nine engine oils previously sampled and found to be questionably labeled were resampled and analyzed. These results are discussed.

This paper briefly reviews the scope of the Oil Labeling Assessment Program and the detailed planning that is Involved in conducting the program. The results of analyses on 136 samples of engine oils that were purchased in the Spring of 1988 are presented and discussed. These samples were all labeled SF, or a combination of SF and a C category. A comparison of 1988 sampling period results with those obtained in 1987 suggests a marked reduction in questionably labeled oils. Additionally, 20 samples of SF oils that were found to be questionably labeled in the 1987 sampling were resampled and these results are discussed.

Of the many research approaches investigated over the years to measure the lubrication properties of aviation turbine fuels, the Ball-on-Cylinder Lubricity Evaluator (BOCLE) has emerged as the most significant test. BOCLE was originally a lubricant research device modified for low viscosity jet fuel when the Air Force encountered fuel control problems in 1965 with JP-4. It proved to be capable of detecting the presence of additives such as corrosion inhibitors which improve boundary lubrication properties and also the absence of natural lubricity agents in highly refined jet fuel. The Coordinating Research Council carried out several programs to investigate test variables such as cylinder type, humidity control and load. A semi-automated version using Falex test rings has now been commercialized and is being used to test fuels from aircraft experiencing abnormal pump wear and fuel control hang-up.

The late and expected improvements in balancing design of hydraulics components to be sure to use real and relatively thick films to enhance the transmission gear of forces and torques with a very low level of friction forces and pratically without heating and wear. The RAFFO process allows high performances, low sensitivity to pollution and small machining cost.

This paper briefly reviews the scope of the Oil Labeling Assessment Program and the detailed planning that was involved in the first year of operation. Then the results of analyses on 309 samples of engine oils labeled SF are presented. It is concluded that the planned program has functioned very well, but it is too early to assess effectiveness of the program in resolving questionably labeled products.